arch/arm/boot/dts/bcm2835-rpi-a-plus.dts

   1 /dts-v1/;
   2 #include "bcm2835.dtsi"
   3 #include "bcm2835-rpi.dtsi"
   4 #include "bcm283x-rpi-usb-host.dtsi"
   5
   6 / {
   7         compatible = "raspberrypi,model-a-plus", "brcm,bcm2835";
   8         model = "Raspberry Pi Model A+";
   9
  10         leds {
  11                 act {
  12                         gpios = <&gpio 47 0>;
  13                 };
  14
  15                 pwr {
  16                         label = "PWR";
  17                         gpios = <&gpio 35 0>;
  18                         default-state = "keep";
  19                         linux,default-trigger = "default-on";
  20                 };
  21         };
  22 };
  23
  24 &gpio {
  25         /*
  26          * This is based on the unreleased schematic for the Model A+.
  27          *
  28          * Legend:
  29          * "NC" = not connected (no rail from the SoC)
  30          * "FOO" = GPIO line named "FOO" on the schematic
  31          * "FOO_N" = GPIO line named "FOO" on schematic, active low
  32          */
  33         gpio-line-names = "SDA0",
  34                           "SCL0",
  35                           "SDA1",
  36                           "SCL1",
  37                           "GPIO_GCLK",
  38                           "GPIO5",
  39                           "GPIO6",
  40                           "SPI_CE1_N",
  41                           "SPI_CE0_N",
  42                           "SPI_MISO",
  43                           "SPI_MOSI",
  44                           "SPI_SCLK",
  45                           "GPIO12",
  46                           "GPIO13",
  47                           /* Serial port */
  48                           "TXD0",
  49                           "RXD0",
  50                           "GPIO16",
  51                           "GPIO17",
  52                           "GPIO18",
  53                           "GPIO19",
  54                           "GPIO20",
  55                           "GPIO21",
  56                           "GPIO22",
  57                           "GPIO23",
  58                           "GPIO24",
  59                           "GPIO25",
  60                           "GPIO26",
  61                           "GPIO27",
  62                           "SDA0",
  63                           "SCL0",
  64                           "NC", /* GPIO30 */
  65                           "NC", /* GPIO31 */
  66                           "CAM_GPIO1", /* GPIO32 */
  67                           "NC", /* GPIO33 */
  68                           "NC", /* GPIO34 */
  69                           "PWR_LOW_N", /* GPIO35 */
  70                           "NC", /* GPIO36 */
  71                           "NC", /* GPIO37 */
  72                           "USB_LIMIT", /* GPIO38 */
  73                           "NC", /* GPIO39 */
  74                           "PWM0_OUT", /* GPIO40 */
  75                           "CAM_GPIO0", /* GPIO41 */
  76                           "NC", /* GPIO42 */
  77                           "NC", /* GPIO43 */
  78                           "NC", /* GPIO44 */
  79                           "PWM1_OUT", /* GPIO45 */
  80                           "HDMI_HPD_N",
  81                           "STATUS_LED",
  82                           /* Used by SD Card */
  83                           "SD_CLK_R",
  84                           "SD_CMD_R",
  85                           "SD_DATA0_R",
  86                           "SD_DATA1_R",
  87                           "SD_DATA2_R",
  88                           "SD_DATA3_R";
  89
  90         pinctrl-0 = <&gpioout &alt0 &i2s_alt0>;
  91
  92         /* I2S interface */
  93         i2s_alt0: i2s_alt0 {
  94                 brcm,pins = <18 19 20 21>;
  95                 brcm,function = <BCM2835_FSEL_ALT0>;
  96         };
  97 };
  98
  99 &hdmi {
 100         hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
 101 };
 102
 103 &uart0 {
 104         pinctrl-names = "default";
 105         pinctrl-0 = <&uart0_gpio14>;
 106         status = "okay";
 107 };