arch/arm/boot/dts/at91-dvk_su60_somc.dtsi

   1 // SPDX-License-Identifier: GPL-2.0
   2 /*
   3  * at91-dvk_su60_somc.dtsi - Device Tree file for the DVK SOM60 base board
   4  *
   5  *  Copyright (C) 2018 Laird,
   6  *                2018 Ben Whitten <ben.whitten@lairdtech.com>
   7  *
   8  */
   9
  10 / {
  11         sound {
  12                 compatible = "atmel,asoc-wm8904";
  13                 pinctrl-names = "default";
  14                 pinctrl-0 = <&pinctrl_pck2_as_audio_mck>;
  15
  16                 atmel,model = "wm8904 @ DVK-SOM60";
  17                 atmel,audio-routing =
  18                         "Headphone Jack", "HPOUTL",
  19                         "Headphone Jack", "HPOUTR",
  20                         "IN2L", "Line In Jack",
  21                         "IN2R", "Line In Jack",
  22                         "Mic", "MICBIAS",
  23                         "IN1L", "Mic";
  24
  25                 atmel,ssc-controller = <&ssc0>;
  26                 atmel,audio-codec = <&wm8904>;
  27
  28                 status = "okay";
  29         };
  30 };
  31
  32 &mmc0 {
  33         status = "okay";
  34
  35         pinctrl-0 = <&pinctrl_mmc0_clk_cmd_dat0 &pinctrl_mmc0_dat1_3 &pinctrl_mmc0_cd>;
  36         slot@0 {
  37                 bus-width = <4>;
  38                 cd-gpios = <&pioE 31 GPIO_ACTIVE_HIGH>;
  39                 cd-inverted;
  40         };
  41 };
  42
  43 &spi0 {
  44         status = "okay";
  45
  46         /* spi0.0: 4M Flash Macronix MX25R4035FM1IL0 */
  47         spi-flash@0 {
  48                 compatible = "mxicy,mx25u4035", "jedec,spi-nor";
  49                 spi-max-frequency = <33000000>;
  50                 reg = <0>;
  51         };
  52 };
  53
  54 &ssc0 {
  55         atmel,clk-from-rk-pin;
  56         status = "okay";
  57 };
  58
  59 &i2c0 {
  60         status = "okay";
  61
  62         wm8904: wm8904@1a {
  63                 compatible = "wlf,wm8904";
  64                 reg = <0x1a>;
  65                 clocks = <&pck2>;
  66                 clock-names = "mclk";
  67         };
  68 };
  69
  70 &i2c1 {
  71         status = "okay";
  72
  73         eeprom@57 {
  74                 compatible = "giantec,gt24c32a", "atmel,24c32";
  75                 reg = <0x57>;
  76                 pagesize = <32>;
  77         };
  78 };
  79
  80 &usart1 {
  81         status = "okay";
  82 };
  83
  84 &usart2 {
  85         status = "okay";
  86 };
  87
  88 &usart3 {
  89         status = "okay";
  90 };
  91
  92 &uart0 {
  93         status = "okay";
  94 };
  95
  96 &dbgu {
  97         status = "okay";
  98 };
  99
 100 &pit {
 101         status = "okay";
 102 };
 103
 104 &adc0 {
 105         status = "okay";
 106 };
 107
 108 &can1 {
 109         status = "okay";
 110 };
 111
 112 &macb0 {
 113         #address-cells = <1>;
 114         #size-cells = <0>;
 115         status = "okay";
 116
 117         ethernet-phy@7 {
 118                 reg = <7>;
 119                 pinctrl-names = "default";
 120                 pinctrl-0 = <&pinctrl_geth_int>;
 121                 interrupt-parent = <&pioB>;
 122                 interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
 123                 txen-skew-ps = <800>;
 124                 txc-skew-ps = <3000>;
 125                 rxdv-skew-ps = <400>;
 126                 rxc-skew-ps = <3000>;
 127                 rxd0-skew-ps = <400>;
 128                 rxd1-skew-ps = <400>;
 129                 rxd2-skew-ps = <400>;
 130                 rxd3-skew-ps = <400>;
 131         };
 132 };
 133
 134 &macb1 {
 135         #address-cells = <1>;
 136         #size-cells = <0>;
 137         status = "okay";
 138
 139         ethernet-phy@1 {
 140                 reg = <1>;
 141                 pinctrl-names = "default";
 142                 pinctrl-0 = <&pinctrl_eth_int>;
 143                 interrupt-parent = <&pioC>;
 144                 interrupts = <10 IRQ_TYPE_EDGE_FALLING>;
 145         };
 146 };
 147
 148 &usb0 {
 149         status = "okay";
 150 };
 151
 152 &usb1 {
 153         status = "okay";
 154 };
 155
 156 &usb2 {
 157         status = "okay";
 158 };
 159