pata_hpt3x3: Workarounds for chipset
authorAlan Cox <alan@redhat.com>
Mon, 5 Jan 2009 14:12:51 +0000 (14:12 +0000)
committerJeff Garzik <jgarzik@redhat.com>
Thu, 8 Jan 2009 21:08:56 +0000 (16:08 -0500)
Correct the DMA bit flags (UDMA and MWDMA were swapped)
Add workarounds so that we clear ERR and INTR bits before issuing a DMA
Add workarounds so that we stop a live DMA before touching the CTL register

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
drivers/ata/pata_hpt3x3.c

index f11a320337c00c52415b453d8e7638e3f6bda447..1c9016edf87a9f1b4cd26460f2a332b2e92ce214 100644 (file)
@@ -23,7 +23,7 @@
 #include <linux/libata.h>
 
 #define DRV_NAME       "pata_hpt3x3"
-#define DRV_VERSION    "0.5.3"
+#define DRV_VERSION    "0.6.1"
 
 /**
  *     hpt3x3_set_piomode              -       PIO setup
@@ -80,14 +80,48 @@ static void hpt3x3_set_dmamode(struct ata_port *ap, struct ata_device *adev)
        r2 &= ~(0x11 << dn);    /* Clear MWDMA and UDMA bits */
 
        if (adev->dma_mode >= XFER_UDMA_0)
-               r2 |= (0x10 << dn);     /* Ultra mode */
+               r2 |= (0x01 << dn);     /* Ultra mode */
        else
-               r2 |= (0x01 << dn);     /* MWDMA */
+               r2 |= (0x10 << dn);     /* MWDMA */
 
        pci_write_config_dword(pdev, 0x44, r1);
        pci_write_config_dword(pdev, 0x48, r2);
 }
-#endif /* CONFIG_PATA_HPT3X3_DMA */
+
+/**
+ *     hpt3x3_freeze           -       DMA workaround
+ *     @ap: port to freeze
+ *
+ *     When freezing an HPT3x3 we must stop any pending DMA before
+ *     writing to the control register or the chip will hang
+ */
+
+static int hpt3x3_freeze(struct ata_port *ap)
+{
+       void __iomem *mmio = ap->ioaddr.bmdma_addr;
+
+       iowrite8(ioread8(mmio + ATA_DMA_CMD) & ~ ATA_DMA_START,
+                       mmio + ATA_DMA_CMD);
+       ata_sff_dma_pause(ap);
+       ata_sff_freeze(ap);
+}
+
+/**
+ *     hpt3x3_bmdma_setup      -       DMA workaround
+ *     @qc: Queued command
+ *
+ *     When issuing BMDMA we must clean up the error/active bits in
+ *     software on this device
+ */
+
+static void hpt3x3_bmdma_setup(struct ata_queued_cmd *qc)
+{
+       struct ata_port *ap = qc->ap;
+       u8 r = ioread8(ap->ioaddr.bmdma_addr + ATA_DMA_STATUS);
+       r |= ATA_DMA_INTR | ATA_DMA_ERR;
+       iowrite8(r, ap->ioaddr.bmdma_addr + ATA_DMA_STATUS);
+       return ata_bmdma_setup(qc);
+}
 
 /**
  *     hpt3x3_atapi_dma        -       ATAPI DMA check
@@ -101,18 +135,23 @@ static int hpt3x3_atapi_dma(struct ata_queued_cmd *qc)
        return 1;
 }
 
+#endif /* CONFIG_PATA_HPT3X3_DMA */
+
 static struct scsi_host_template hpt3x3_sht = {
        ATA_BMDMA_SHT(DRV_NAME),
 };
 
 static struct ata_port_operations hpt3x3_port_ops = {
        .inherits       = &ata_bmdma_port_ops,
-       .check_atapi_dma= hpt3x3_atapi_dma,
        .cable_detect   = ata_cable_40wire,
        .set_piomode    = hpt3x3_set_piomode,
 #if defined(CONFIG_PATA_HPT3X3_DMA)
        .set_dmamode    = hpt3x3_set_dmamode,
+       .bmdma_setup    = hpt3x3_bmdma_setup,
+       .check_atapi_dma= hpt3x3_atapi_dma,
+       .freeze         = hpt3x3_freeze,
 #endif
+       
 };
 
 /**
@@ -257,4 +296,4 @@ MODULE_DEVICE_TABLE(pci, hpt3x3);
 MODULE_VERSION(DRV_VERSION);
 
 module_init(hpt3x3_init);
-module_exit(hpt3x3_exit);
+module_exit(hpt3x3_exit);
\ No newline at end of file