pps: add parallel port PPS signal generator
authorAlexander Gordeev <lasaine@lvk.cs.msu.su>
Thu, 13 Jan 2011 01:00:59 +0000 (17:00 -0800)
committerLinus Torvalds <torvalds@linux-foundation.org>
Thu, 13 Jan 2011 16:03:21 +0000 (08:03 -0800)
Add PPS signal generator which utilizes STROBE pin of a parallel port to
send PPS signals.  It uses parport abstraction layer and hrtimers to
precisely control the signal.

[akpm@linux-foundation.org: fix build]
Signed-off-by: Alexander Gordeev <lasaine@lvk.cs.msu.su>
Acked-by: Rodolfo Giometti <giometti@linux.it>
Cc: john stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Documentation/pps/pps.txt
drivers/pps/Kconfig
drivers/pps/Makefile
drivers/pps/generators/Kconfig [new file with mode: 0644]
drivers/pps/generators/Makefile [new file with mode: 0644]
drivers/pps/generators/pps_gen_parport.c [new file with mode: 0644]

index 125f4ab4899838d357e4cfb73d27b58397afcd3d..d35dcdd82ff6a6c93b2dae00be717080b9b21cb1 100644 (file)
@@ -170,3 +170,49 @@ and the run ppstest as follow:
 
 Please, note that to compile userland programs you need the file timepps.h
 (see Documentation/pps/).
+
+
+Generators
+----------
+
+Sometimes one needs to be able not only to catch PPS signals but to produce
+them also. For example, running a distributed simulation, which requires
+computers' clock to be synchronized very tightly. One way to do this is to
+invent some complicated hardware solutions but it may be neither necessary
+nor affordable. The cheap way is to load a PPS generator on one of the
+computers (master) and PPS clients on others (slaves), and use very simple
+cables to deliver signals using parallel ports, for example.
+
+Parallel port cable pinout:
+pin    name    master      slave
+1      STROBE    *------     *
+2      D0        *     |     *
+3      D1        *     |     *
+4      D2        *     |     *
+5      D3        *     |     *
+6      D4        *     |     *
+7      D5        *     |     *
+8      D6        *     |     *
+9      D7        *     |     *
+10     ACK       *     ------*
+11     BUSY      *           *
+12     PE        *           *
+13     SEL       *           *
+14     AUTOFD    *           *
+15     ERROR     *           *
+16     INIT      *           *
+17     SELIN     *           *
+18-25  GND       *-----------*
+
+Please note that parallel port interrupt occurs only on high->low transition,
+so it is used for PPS assert edge. PPS clear edge can be determined only
+using polling in the interrupt handler which actually can be done way more
+precisely because interrupt handling delays can be quite big and random. So
+current parport PPS generator implementation (pps_gen_parport module) is
+geared towards using the clear edge for time synchronization.
+
+Clear edge polling is done with disabled interrupts so it's better to select
+delay between assert and clear edge as small as possible to reduce system
+latencies. But if it is too small slave won't be able to capture clear edge
+transition. The default of 30us should be good enough in most situations.
+The delay can be selected using 'delay' pps_gen_parport module parameter.
index 0ad5ff38bfec6448b9d540dde492d96f70b72a9b..f0d3376b58ba1710a7dbc7ab45cd89ca79e87041 100644 (file)
@@ -41,4 +41,6 @@ config NTP_PPS
 
 source drivers/pps/clients/Kconfig
 
+source drivers/pps/generators/Kconfig
+
 endmenu
index 77c23457b739685009ae5713a12f3c014090ad5a..4483eaadaddd7e76702ef0a18e4eed9442ead389 100644 (file)
@@ -5,6 +5,6 @@
 pps_core-y                     := pps.o kapi.o sysfs.o
 pps_core-$(CONFIG_NTP_PPS)     += kc.o
 obj-$(CONFIG_PPS)              := pps_core.o
-obj-y                          += clients/
+obj-y                          += clients/ generators/
 
 ccflags-$(CONFIG_PPS_DEBUG) := -DDEBUG
diff --git a/drivers/pps/generators/Kconfig b/drivers/pps/generators/Kconfig
new file mode 100644 (file)
index 0000000..5fbd614
--- /dev/null
@@ -0,0 +1,17 @@
+#
+# PPS generators configuration
+#
+
+if PPS
+
+comment "PPS generators support"
+
+config PPS_GENERATOR_PARPORT
+       tristate "Parallel port PPS signal generator"
+       depends on PARPORT != n && GENERIC_TIME
+       help
+         If you say yes here you get support for a PPS signal generator which
+         utilizes STROBE pin of a parallel port to send PPS signals. It uses
+         parport abstraction layer and hrtimers to precisely control the signal.
+
+endif
diff --git a/drivers/pps/generators/Makefile b/drivers/pps/generators/Makefile
new file mode 100644 (file)
index 0000000..303304a
--- /dev/null
@@ -0,0 +1,9 @@
+#
+# Makefile for PPS generators.
+#
+
+obj-$(CONFIG_PPS_GENERATOR_PARPORT) += pps_gen_parport.o
+
+ifeq ($(CONFIG_PPS_DEBUG),y)
+EXTRA_CFLAGS += -DDEBUG
+endif
diff --git a/drivers/pps/generators/pps_gen_parport.c b/drivers/pps/generators/pps_gen_parport.c
new file mode 100644 (file)
index 0000000..a15fe25
--- /dev/null
@@ -0,0 +1,275 @@
+/*
+ * pps_gen_parport.c -- kernel parallel port PPS signal generator
+ *
+ *
+ * Copyright (C) 2009   Alexander Gordeev <lasaine@lvk.cs.msu.su>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+
+/*
+ * TODO:
+ * fix issues when realtime clock is adjusted in a leap
+ */
+
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/time.h>
+#include <linux/hrtimer.h>
+#include <linux/parport.h>
+
+#define DRVDESC "parallel port PPS signal generator"
+
+#define SIGNAL         0
+#define NO_SIGNAL      PARPORT_CONTROL_STROBE
+
+/* module parameters */
+
+#define SEND_DELAY_MAX         100000
+
+static unsigned int send_delay = 30000;
+MODULE_PARM_DESC(delay,
+       "Delay between setting and dropping the signal (ns)");
+module_param_named(delay, send_delay, uint, 0);
+
+
+#define SAFETY_INTERVAL        3000    /* set the hrtimer earlier for safety (ns) */
+
+/* internal per port structure */
+struct pps_generator_pp {
+       struct pardevice *pardev;       /* parport device */
+       struct hrtimer timer;
+       long port_write_time;           /* calibrated port write time (ns) */
+};
+
+static struct pps_generator_pp device = {
+       .pardev = NULL,
+};
+
+static int attached;
+
+/* calibrated time between a hrtimer event and the reaction */
+static long hrtimer_error = SAFETY_INTERVAL;
+
+/* the kernel hrtimer event */
+static enum hrtimer_restart hrtimer_event(struct hrtimer *timer)
+{
+       struct timespec expire_time, ts1, ts2, ts3, dts;
+       struct pps_generator_pp *dev;
+       struct parport *port;
+       long lim, delta;
+       unsigned long flags;
+
+       /* NB: approx time with blocked interrupts =
+          send_delay + 3 * SAFETY_INTERVAL */
+       local_irq_save(flags);
+
+       /* first of all we get the time stamp... */
+       getnstimeofday(&ts1);
+       expire_time = ktime_to_timespec(hrtimer_get_softexpires(timer));
+       dev = container_of(timer, struct pps_generator_pp, timer);
+       lim = NSEC_PER_SEC - send_delay - dev->port_write_time;
+
+       /* check if we are late */
+       if (expire_time.tv_sec != ts1.tv_sec || ts1.tv_nsec > lim) {
+               local_irq_restore(flags);
+               pr_err("we are late this time %ld.%09ld\n",
+                               ts1.tv_sec, ts1.tv_nsec);
+               goto done;
+       }
+
+       /* busy loop until the time is right for an assert edge */
+       do {
+               getnstimeofday(&ts2);
+       } while (expire_time.tv_sec == ts2.tv_sec && ts2.tv_nsec < lim);
+
+       /* set the signal */
+       port = dev->pardev->port;
+       port->ops->write_control(port, SIGNAL);
+
+       /* busy loop until the time is right for a clear edge */
+       lim = NSEC_PER_SEC - dev->port_write_time;
+       do {
+               getnstimeofday(&ts2);
+       } while (expire_time.tv_sec == ts2.tv_sec && ts2.tv_nsec < lim);
+
+       /* unset the signal */
+       port->ops->write_control(port, NO_SIGNAL);
+
+       getnstimeofday(&ts3);
+
+       local_irq_restore(flags);
+
+       /* update calibrated port write time */
+       dts = timespec_sub(ts3, ts2);
+       dev->port_write_time =
+               (dev->port_write_time + timespec_to_ns(&dts)) >> 1;
+
+done:
+       /* update calibrated hrtimer error */
+       dts = timespec_sub(ts1, expire_time);
+       delta = timespec_to_ns(&dts);
+       /* If the new error value is bigger then the old, use the new
+        * value, if not then slowly move towards the new value. This
+        * way it should be safe in bad conditions and efficient in
+        * good conditions.
+        */
+       if (delta >= hrtimer_error)
+               hrtimer_error = delta;
+       else
+               hrtimer_error = (3 * hrtimer_error + delta) >> 2;
+
+       /* update the hrtimer expire time */
+       hrtimer_set_expires(timer,
+                       ktime_set(expire_time.tv_sec + 1,
+                               NSEC_PER_SEC - (send_delay +
+                               dev->port_write_time + SAFETY_INTERVAL +
+                               2 * hrtimer_error)));
+
+       return HRTIMER_RESTART;
+}
+
+/* calibrate port write time */
+#define PORT_NTESTS_SHIFT      5
+static void calibrate_port(struct pps_generator_pp *dev)
+{
+       struct parport *port = dev->pardev->port;
+       int i;
+       long acc = 0;
+
+       for (i = 0; i < (1 << PORT_NTESTS_SHIFT); i++) {
+               struct timespec a, b;
+               unsigned long irq_flags;
+
+               local_irq_save(irq_flags);
+               getnstimeofday(&a);
+               port->ops->write_control(port, NO_SIGNAL);
+               getnstimeofday(&b);
+               local_irq_restore(irq_flags);
+
+               b = timespec_sub(b, a);
+               acc += timespec_to_ns(&b);
+       }
+
+       dev->port_write_time = acc >> PORT_NTESTS_SHIFT;
+       pr_info("port write takes %ldns\n", dev->port_write_time);
+}
+
+static inline ktime_t next_intr_time(struct pps_generator_pp *dev)
+{
+       struct timespec ts;
+
+       getnstimeofday(&ts);
+
+       return ktime_set(ts.tv_sec +
+                       ((ts.tv_nsec > 990 * NSEC_PER_MSEC) ? 1 : 0),
+                       NSEC_PER_SEC - (send_delay +
+                       dev->port_write_time + 3 * SAFETY_INTERVAL));
+}
+
+static void parport_attach(struct parport *port)
+{
+       if (attached) {
+               /* we already have a port */
+               return;
+       }
+
+       device.pardev = parport_register_device(port, KBUILD_MODNAME,
+                       NULL, NULL, NULL, 0, &device);
+       if (!device.pardev) {
+               pr_err("couldn't register with %s\n", port->name);
+               return;
+       }
+
+       if (parport_claim_or_block(device.pardev) < 0) {
+               pr_err("couldn't claim %s\n", port->name);
+               goto err_unregister_dev;
+       }
+
+       pr_info("attached to %s\n", port->name);
+       attached = 1;
+
+       calibrate_port(&device);
+
+       hrtimer_init(&device.timer, CLOCK_REALTIME, HRTIMER_MODE_ABS);
+       device.timer.function = hrtimer_event;
+#ifdef CONFIG_PREEMPT_RT
+       /* hrtimer interrupt will run in the interrupt context with this */
+       device.timer.irqsafe = 1;
+#endif
+
+       hrtimer_start(&device.timer, next_intr_time(&device), HRTIMER_MODE_ABS);
+
+       return;
+
+err_unregister_dev:
+       parport_unregister_device(device.pardev);
+}
+
+static void parport_detach(struct parport *port)
+{
+       if (port->cad != device.pardev)
+               return; /* not our port */
+
+       hrtimer_cancel(&device.timer);
+       parport_release(device.pardev);
+       parport_unregister_device(device.pardev);
+}
+
+static struct parport_driver pps_gen_parport_driver = {
+       .name = KBUILD_MODNAME,
+       .attach = parport_attach,
+       .detach = parport_detach,
+};
+
+/* module staff */
+
+static int __init pps_gen_parport_init(void)
+{
+       int ret;
+
+       pr_info(DRVDESC "\n");
+
+       if (send_delay > SEND_DELAY_MAX) {
+               pr_err("delay value should be not greater"
+                               " then %d\n", SEND_DELAY_MAX);
+               return -EINVAL;
+       }
+
+       ret = parport_register_driver(&pps_gen_parport_driver);
+       if (ret) {
+               pr_err("unable to register with parport\n");
+               return ret;
+       }
+
+       return  0;
+}
+
+static void __exit pps_gen_parport_exit(void)
+{
+       parport_unregister_driver(&pps_gen_parport_driver);
+       pr_info("hrtimer avg error is %ldns\n", hrtimer_error);
+}
+
+module_init(pps_gen_parport_init);
+module_exit(pps_gen_parport_exit);
+
+MODULE_AUTHOR("Alexander Gordeev <lasaine@lvk.cs.msu.su>");
+MODULE_DESCRIPTION(DRVDESC);
+MODULE_LICENSE("GPL");