#define DRV_MODULE_NAME "tg3"
#define PFX DRV_MODULE_NAME ": "
-#define DRV_MODULE_VERSION "3.57"
-#define DRV_MODULE_RELDATE "Apr 28, 2006"
+#define DRV_MODULE_VERSION "3.60"
+#define DRV_MODULE_RELDATE "June 17, 2006"
#define TG3_DEF_MAC_MODE 0
#define TG3_DEF_RX_MODE 0
PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0UL },
{ PCI_VENDOR_ID_BROADCOM, PCI_DEVICE_ID_TIGON3_5755M,
PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0UL },
+ { PCI_VENDOR_ID_BROADCOM, PCI_DEVICE_ID_TIGON3_5786,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0UL },
{ PCI_VENDOR_ID_BROADCOM, PCI_DEVICE_ID_TIGON3_5787,
PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0UL },
{ PCI_VENDOR_ID_BROADCOM, PCI_DEVICE_ID_TIGON3_5787M,
return err;
}
+/* This is called whenever we suspect that the system chipset is re-
+ * ordering the sequence of MMIO to the tx send mailbox. The symptom
+ * is bogus tx completions. We try to recover by setting the
+ * TG3_FLAG_MBOX_WRITE_REORDER flag and resetting the chip later
+ * in the workqueue.
+ */
+static void tg3_tx_recover(struct tg3 *tp)
+{
+ BUG_ON((tp->tg3_flags & TG3_FLAG_MBOX_WRITE_REORDER) ||
+ tp->write32_tx_mbox == tg3_write_indirect_mbox);
+
+ printk(KERN_WARNING PFX "%s: The system may be re-ordering memory-"
+ "mapped I/O cycles to the network device, attempting to "
+ "recover. Please report the problem to the driver maintainer "
+ "and include system chipset information.\n", tp->dev->name);
+
+ spin_lock(&tp->lock);
+ spin_lock(&tp->tx_lock);
+ tp->tg3_flags |= TG3_FLAG_TX_RECOVERY_PENDING;
+ spin_unlock(&tp->tx_lock);
+ spin_unlock(&tp->lock);
+}
+
/* Tigon3 never reports partial packet sends. So we do not
* need special logic to handle SKBs that have not had all
* of their frags sent yet, like SunGEM does.
while (sw_idx != hw_idx) {
struct tx_ring_info *ri = &tp->tx_buffers[sw_idx];
struct sk_buff *skb = ri->skb;
- int i;
+ int i, tx_bug = 0;
+
+ if (unlikely(skb == NULL)) {
+ tg3_tx_recover(tp);
+ return;
+ }
- BUG_ON(skb == NULL);
pci_unmap_single(tp->pdev,
pci_unmap_addr(ri, mapping),
skb_headlen(skb),
sw_idx = NEXT_TX(sw_idx);
for (i = 0; i < skb_shinfo(skb)->nr_frags; i++) {
- BUG_ON(sw_idx == hw_idx);
-
ri = &tp->tx_buffers[sw_idx];
- BUG_ON(ri->skb != NULL);
+ if (unlikely(ri->skb != NULL || sw_idx == hw_idx))
+ tx_bug = 1;
pci_unmap_page(tp->pdev,
pci_unmap_addr(ri, mapping),
}
dev_kfree_skb(skb);
+
+ if (unlikely(tx_bug)) {
+ tg3_tx_recover(tp);
+ return;
+ }
}
tp->tx_cons = sw_idx;
/* run TX completion thread */
if (sblk->idx[0].tx_consumer != tp->tx_cons) {
tg3_tx(tp);
+ if (unlikely(tp->tg3_flags & TG3_FLAG_TX_RECOVERY_PENDING)) {
+ netif_rx_complete(netdev);
+ schedule_work(&tp->reset_task);
+ return 0;
+ }
}
/* run RX thread, within the bounds set by NAPI.
restart_timer = tp->tg3_flags2 & TG3_FLG2_RESTART_TIMER;
tp->tg3_flags2 &= ~TG3_FLG2_RESTART_TIMER;
+ if (tp->tg3_flags & TG3_FLAG_TX_RECOVERY_PENDING) {
+ tp->write32_tx_mbox = tg3_write32_tx_mbox;
+ tp->write32_rx_mbox = tg3_write_flush_reg32;
+ tp->tg3_flags |= TG3_FLAG_MBOX_WRITE_REORDER;
+ tp->tg3_flags &= ~TG3_FLAG_TX_RECOVERY_PENDING;
+ }
+
tg3_halt(tp, RESET_KIND_SHUTDOWN, 0);
tg3_init_hw(tp, 1);
/* tp->lock is held. */
static void tg3_write_sig_pre_reset(struct tg3 *tp, int kind)
{
- if (!(tp->tg3_flags2 & TG3_FLG2_SUN_570X))
- tg3_write_mem(tp, NIC_SRAM_FIRMWARE_MBOX,
- NIC_SRAM_FIRMWARE_MBOX_MAGIC1);
+ tg3_write_mem(tp, NIC_SRAM_FIRMWARE_MBOX,
+ NIC_SRAM_FIRMWARE_MBOX_MAGIC1);
if (tp->tg3_flags2 & TG3_FLG2_ASF_NEW_HANDSHAKE) {
switch (kind) {
void (*write_op)(struct tg3 *, u32, u32);
int i;
- if (!(tp->tg3_flags2 & TG3_FLG2_SUN_570X)) {
- tg3_nvram_lock(tp);
- /* No matching tg3_nvram_unlock() after this because
- * chip reset below will undo the nvram lock.
- */
- tp->nvram_lock_cnt = 0;
- }
+ tg3_nvram_lock(tp);
+
+ /* No matching tg3_nvram_unlock() after this because
+ * chip reset below will undo the nvram lock.
+ */
+ tp->nvram_lock_cnt = 0;
if (GET_ASIC_REV(tp->pci_chip_rev_id) == ASIC_REV_5752 ||
GET_ASIC_REV(tp->pci_chip_rev_id) == ASIC_REV_5755 ||
tw32_f(MAC_MODE, 0);
udelay(40);
- if (!(tp->tg3_flags2 & TG3_FLG2_SUN_570X)) {
- /* Wait for firmware initialization to complete. */
- for (i = 0; i < 100000; i++) {
- tg3_read_mem(tp, NIC_SRAM_FIRMWARE_MBOX, &val);
- if (val == ~NIC_SRAM_FIRMWARE_MBOX_MAGIC1)
- break;
- udelay(10);
- }
- if (i >= 100000) {
- printk(KERN_ERR PFX "tg3_reset_hw timed out for %s, "
- "firmware will not restart magic=%08x\n",
- tp->dev->name, val);
- return -ENODEV;
- }
+ /* Wait for firmware initialization to complete. */
+ for (i = 0; i < 100000; i++) {
+ tg3_read_mem(tp, NIC_SRAM_FIRMWARE_MBOX, &val);
+ if (val == ~NIC_SRAM_FIRMWARE_MBOX_MAGIC1)
+ break;
+ udelay(10);
+ }
+
+ /* Chip might not be fitted with firmare. Some Sun onboard
+ * parts are configured like that. So don't signal the timeout
+ * of the above loop as an error, but do report the lack of
+ * running firmware once.
+ */
+ if (i >= 100000 &&
+ !(tp->tg3_flags2 & TG3_FLG2_NO_FWARE_REPORTED)) {
+ tp->tg3_flags2 |= TG3_FLG2_NO_FWARE_REPORTED;
+
+ printk(KERN_INFO PFX "%s: No firmware running.\n",
+ tp->dev->name);
}
if ((tp->tg3_flags2 & TG3_FLG2_PCI_EXPRESS) &&
TG3_STAT_ADD32(&sp->rx_frame_too_long_errors, MAC_RX_STATS_FRAME_TOO_LONG);
TG3_STAT_ADD32(&sp->rx_jabbers, MAC_RX_STATS_JABBERS);
TG3_STAT_ADD32(&sp->rx_undersize_packets, MAC_RX_STATS_UNDERSIZE);
+
+ TG3_STAT_ADD32(&sp->rxbds_empty, RCVLPC_NO_RCV_BD_CNT);
+ TG3_STAT_ADD32(&sp->rx_discards, RCVLPC_IN_DISCARDS_CNT);
+ TG3_STAT_ADD32(&sp->rx_errors, RCVLPC_IN_ERRORS_CNT);
}
static void tg3_timer(unsigned long __opaque)
cmd->supported |= (SUPPORTED_1000baseT_Half |
SUPPORTED_1000baseT_Full);
- if (!(tp->tg3_flags2 & TG3_FLG2_ANY_SERDES))
+ if (!(tp->tg3_flags2 & TG3_FLG2_ANY_SERDES)) {
cmd->supported |= (SUPPORTED_100baseT_Half |
SUPPORTED_100baseT_Full |
SUPPORTED_10baseT_Half |
SUPPORTED_10baseT_Full |
SUPPORTED_MII);
- else
+ cmd->port = PORT_TP;
+ } else {
cmd->supported |= SUPPORTED_FIBRE;
+ cmd->port = PORT_FIBRE;
+ }
cmd->advertising = tp->link_config.advertising;
if (netif_running(dev)) {
cmd->speed = tp->link_config.active_speed;
cmd->duplex = tp->link_config.active_duplex;
}
- cmd->port = 0;
cmd->phy_address = PHY_ADDR;
cmd->transceiver = 0;
cmd->autoneg = tp->link_config.autoneg;
tx_len = 1514;
skb = dev_alloc_skb(tx_len);
+ if (!skb)
+ return -ENOMEM;
+
tx_data = skb_put(skb, tx_len);
memcpy(tx_data, tp->dev->dev_addr, 6);
memset(tx_data + 6, 0x0, 8);
{
int j;
- if (tp->tg3_flags2 & TG3_FLG2_SUN_570X)
- return;
-
tw32_f(GRC_EEPROM_ADDR,
(EEPROM_ADDR_FSM_RESET |
(EEPROM_DEFAULT_CLOCK_PERIOD <<
{
int ret;
- if (tp->tg3_flags2 & TG3_FLG2_SUN_570X) {
- printk(KERN_ERR PFX "Attempt to do nvram_read on Sun 570X\n");
- return -EINVAL;
- }
-
if (!(tp->tg3_flags & TG3_FLAG_NVRAM))
return tg3_nvram_read_using_eeprom(tp, offset, val);
{
int ret;
- if (tp->tg3_flags2 & TG3_FLG2_SUN_570X) {
- printk(KERN_ERR PFX "Attempt to do nvram_write on Sun 570X\n");
- return -EINVAL;
- }
-
if (tp->tg3_flags & TG3_FLAG_EEPROM_WRITE_PROT) {
tw32_f(GRC_LOCAL_CTRL, tp->grc_local_ctrl &
~GRC_LCLCTRL_GPIO_OUTPUT1);
pci_write_config_dword(tp->pdev, TG3PCI_MISC_HOST_CTRL,
tp->misc_host_ctrl);
+ /* The memory arbiter has to be enabled in order for SRAM accesses
+ * to succeed. Normally on powerup the tg3 chip firmware will make
+ * sure it is enabled, but other entities such as system netboot
+ * code might disable it.
+ */
+ val = tr32(MEMARB_MODE);
+ tw32(MEMARB_MODE, val | MEMARB_MODE_ENABLE);
+
tp->phy_id = PHY_ID_INVALID;
tp->led_ctrl = LED_CTRL_MODE_PHY_1;
- /* Do not even try poking around in here on Sun parts. */
- if (tp->tg3_flags2 & TG3_FLG2_SUN_570X) {
- /* All SUN chips are built-in LOMs. */
- tp->tg3_flags |= TG3_FLAG_EEPROM_WRITE_PROT;
- return;
- }
+ /* Assume an onboard device by default. */
+ tp->tg3_flags |= TG3_FLAG_EEPROM_WRITE_PROT;
tg3_read_mem(tp, NIC_SRAM_DATA_SIG, &val);
if (val == NIC_SRAM_DATA_SIG_MAGIC) {
if (nic_cfg & NIC_SRAM_DATA_CFG_EEPROM_WP)
tp->tg3_flags |= TG3_FLAG_EEPROM_WRITE_PROT;
+ else
+ tp->tg3_flags &= ~TG3_FLAG_EEPROM_WRITE_PROT;
if (nic_cfg & NIC_SRAM_DATA_CFG_ASF_ENABLE) {
tp->tg3_flags |= TG3_FLAG_ENABLE_ASF;
int i;
u32 magic;
- if (tp->tg3_flags2 & TG3_FLG2_SUN_570X) {
- /* Sun decided not to put the necessary bits in the
- * NVRAM of their onboard tg3 parts :(
- */
- strcpy(tp->board_part_number, "Sun 570X");
- return;
- }
-
if (tg3_nvram_read_swab(tp, 0x0, &magic))
- return;
+ goto out_not_found;
if (magic == TG3_EEPROM_MAGIC) {
for (i = 0; i < 256; i += 4) {
break;
msleep(1);
}
+ if (!(tmp16 & 0x8000))
+ goto out_not_found;
+
pci_read_config_dword(tp->pdev, vpd_cap + PCI_VPD_DATA,
&tmp);
tmp = cpu_to_le32(tmp);
}
}
-#ifdef CONFIG_SPARC64
-static int __devinit tg3_is_sun_570X(struct tg3 *tp)
-{
- struct pci_dev *pdev = tp->pdev;
- struct pcidev_cookie *pcp = pdev->sysdata;
-
- if (pcp != NULL) {
- int node = pcp->prom_node;
- u32 venid;
- int err;
-
- err = prom_getproperty(node, "subsystem-vendor-id",
- (char *) &venid, sizeof(venid));
- if (err == 0 || err == -1)
- return 0;
- if (venid == PCI_VENDOR_ID_SUN)
- return 1;
-
- /* TG3 chips onboard the SunBlade-2500 don't have the
- * subsystem-vendor-id set to PCI_VENDOR_ID_SUN but they
- * are distinguishable from non-Sun variants by being
- * named "network" by the firmware. Non-Sun cards will
- * show up as being named "ethernet".
- */
- if (!strcmp(pcp->prom_name, "network"))
- return 1;
- }
- return 0;
-}
-#endif
-
static int __devinit tg3_get_invariants(struct tg3 *tp)
{
static struct pci_device_id write_reorder_chipsets[] = {
u16 pci_cmd;
int err;
-#ifdef CONFIG_SPARC64
- if (tg3_is_sun_570X(tp))
- tp->tg3_flags2 |= TG3_FLG2_SUN_570X;
-#endif
-
/* Force memory write invalidate off. If we leave it on,
* then on 5700_BX chips we have to enable a workaround.
* The workaround is to set the TG3PCI_DMA_RW_CTRL boundary
if (tp->write32 == tg3_write_indirect_reg32 ||
((tp->tg3_flags & TG3_FLAG_PCIX_MODE) &&
(GET_ASIC_REV(tp->pci_chip_rev_id) == ASIC_REV_5700 ||
- GET_ASIC_REV(tp->pci_chip_rev_id) == ASIC_REV_5701)) ||
- (tp->tg3_flags2 & TG3_FLG2_SUN_570X))
+ GET_ASIC_REV(tp->pci_chip_rev_id) == ASIC_REV_5701)))
tp->tg3_flags |= TG3_FLAG_SRAM_USE_CONFIG;
/* Get eeprom hw config before calling tg3_set_power_state().
#endif
mac_offset = 0x7c;
- if ((GET_ASIC_REV(tp->pci_chip_rev_id) == ASIC_REV_5704 &&
- !(tp->tg3_flags & TG3_FLG2_SUN_570X)) ||
+ if ((GET_ASIC_REV(tp->pci_chip_rev_id) == ASIC_REV_5704) ||
(tp->tg3_flags2 & TG3_FLG2_5780_CLASS)) {
if (tr32(TG3PCI_DUAL_MAC_CTRL) & DUAL_MAC_CTRL_ID)
mac_offset = 0xcc;
}
if (!addr_ok) {
/* Next, try NVRAM. */
- if (!(tp->tg3_flags & TG3_FLG2_SUN_570X) &&
- !tg3_nvram_read(tp, mac_offset + 0, &hi) &&
+ if (!tg3_nvram_read(tp, mac_offset + 0, &hi) &&
!tg3_nvram_read(tp, mac_offset + 4, &lo)) {
dev->dev_addr[0] = ((hi >> 16) & 0xff);
dev->dev_addr[1] = ((hi >> 24) & 0xff);
git.samba.org / sfrench / cifs-2.6.git / blobdiff