#include <linux/delay.h>
#include <linux/crc32.h>
#include <linux/phy.h>
+
+#include <asm/cpu.h>
#include <asm/mipsregs.h>
#include <asm/irq.h>
#include <asm/io.h>
#include <asm/processor.h>
-#include <asm/mach-au1x00/au1000.h>
-#include <asm/cpu.h>
+#include <au1000.h>
+#include <prom.h>
+
#include "au1000_eth.h"
#ifdef AU1000_ETH_DEBUG
static void au1000_adjust_link(struct net_device *);
static void enable_mac(struct net_device *, int);
-// externs
-extern int get_ethernet_addr(char *ethernet_addr);
-extern void str2eaddr(unsigned char *ea, unsigned char *str);
-extern char * prom_getcmdline(void);
-
/*
* Theory of operation
*
static int num_ifs;
/*
- * Setup the base address and interupt of the Au1xxx ethernet macs
+ * Setup the base address and interrupt of the Au1xxx ethernet macs
* based on cpu type and whether the interface is enabled in sys_pinfunc
* register. The last interface is enabled if SYS_PF_NI2 (bit 4) is 0.
*/
struct au1000_private *aup = NULL;
struct net_device *dev = NULL;
db_dest_t *pDB, *pDBfree;
- char *pmac, *argptr;
char ethaddr[6];
int irq, i, err;
u32 base, macen;
au_macs[port_num] = aup;
if (port_num == 0) {
- /* Check the environment variables first */
- if (get_ethernet_addr(ethaddr) == 0)
+ if (prom_get_ethernet_addr(ethaddr) == 0)
memcpy(au1000_mac_addr, ethaddr, sizeof(au1000_mac_addr));
else {
- /* Check command line */
- argptr = prom_getcmdline();
- if ((pmac = strstr(argptr, "ethaddr=")) == NULL)
- printk(KERN_INFO "%s: No MAC address found\n",
- dev->name);
+ printk(KERN_INFO "%s: No MAC address found\n",
+ dev->name);
/* Use the hard coded MAC addresses */
- else {
- str2eaddr(ethaddr, pmac + strlen("ethaddr="));
- memcpy(au1000_mac_addr, ethaddr,
- sizeof(au1000_mac_addr));
- }
}
setup_hw_rings(aup, MAC0_RX_DMA_ADDR, MAC0_TX_DMA_ADDR);
aup->mii_bus.write = mdiobus_write;
aup->mii_bus.reset = mdiobus_reset;
aup->mii_bus.name = "au1000_eth_mii";
- aup->mii_bus.id = aup->mac_id;
+ snprintf(aup->mii_bus.id, MII_BUS_ID_SIZE, "%x", aup->mac_id);
aup->mii_bus.irq = kmalloc(sizeof(int)*PHY_MAX_ADDR, GFP_KERNEL);
for(i = 0; i < PHY_MAX_ADDR; ++i)
aup->mii_bus.irq[i] = PHY_POLL;
/* if known, set corresponding PHY IRQs */
#if defined(AU1XXX_PHY_STATIC_CONFIG)
# if defined(AU1XXX_PHY0_IRQ)
- if (AU1XXX_PHY0_BUSID == aup->mii_bus.id)
+ if (AU1XXX_PHY0_BUSID == aup->mac_id)
aup->mii_bus.irq[AU1XXX_PHY0_ADDR] = AU1XXX_PHY0_IRQ;
# endif
# if defined(AU1XXX_PHY1_IRQ)
- if (AU1XXX_PHY1_BUSID == aup->mii_bus.id)
+ if (AU1XXX_PHY1_BUSID == aup->mac_id)
aup->mii_bus.irq[AU1XXX_PHY1_ADDR] = AU1XXX_PHY1_IRQ;
# endif
#endif
*/
static irqreturn_t au1000_interrupt(int irq, void *dev_id)
{
- struct net_device *dev = (struct net_device *) dev_id;
-
- if (dev == NULL) {
- printk(KERN_ERR "%s: isr: null dev ptr\n", dev->name);
- return IRQ_RETVAL(1);
- }
+ struct net_device *dev = dev_id;
/* Handle RX interrupts first to minimize chance of overrun */