eeh_error_buf_size = RTAS_ERROR_LOG_MAX;
}
+ /* Set EEH probe mode */
+ eeh_probe_mode_set(EEH_PROBE_MODE_DEVTREE);
+
return 0;
}
+/**
+ * pseries_eeh_of_probe - EEH probe on the given device
+ * @dn: OF node
+ * @flag: Unused
+ *
+ * When EEH module is installed during system boot, all PCI devices
+ * are checked one by one to see if it supports EEH. The function
+ * is introduced for the purpose.
+ */
+static void *pseries_eeh_of_probe(struct device_node *dn, void *flag)
+{
+ struct eeh_dev *edev;
+ struct eeh_pe pe;
+ const u32 *class_code, *vendor_id, *device_id;
+ const u32 *regs;
+ int enable = 0;
+ int ret;
+
+ /* Retrieve OF node and eeh device */
+ edev = of_node_to_eeh_dev(dn);
+ if (!of_device_is_available(dn))
+ return NULL;
+
+ /* Retrieve class/vendor/device IDs */
+ class_code = of_get_property(dn, "class-code", NULL);
+ vendor_id = of_get_property(dn, "vendor-id", NULL);
+ device_id = of_get_property(dn, "device-id", NULL);
+
+ /* Skip for bad OF node or PCI-ISA bridge */
+ if (!class_code || !vendor_id || !device_id)
+ return NULL;
+ if (dn->type && !strcmp(dn->type, "isa"))
+ return NULL;
+
+ /* Update class code and mode of eeh device */
+ edev->class_code = *class_code;
+ edev->mode = 0;
+
+ /* Retrieve the device address */
+ regs = of_get_property(dn, "reg", NULL);
+ if (!regs) {
+ pr_warning("%s: OF node property %s::reg not found\n",
+ __func__, dn->full_name);
+ return NULL;
+ }
+
+ /* Initialize the fake PE */
+ memset(&pe, 0, sizeof(struct eeh_pe));
+ pe.phb = edev->phb;
+ pe.config_addr = regs[0];
+
+ /* Enable EEH on the device */
+ ret = eeh_ops->set_option(&pe, EEH_OPT_ENABLE);
+ if (!ret) {
+ edev->config_addr = regs[0];
+ /* Retrieve PE address */
+ edev->pe_config_addr = eeh_ops->get_pe_addr(&pe);
+ pe.addr = edev->pe_config_addr;
+
+ /* Some older systems (Power4) allow the ibm,set-eeh-option
+ * call to succeed even on nodes where EEH is not supported.
+ * Verify support explicitly.
+ */
+ ret = eeh_ops->get_state(&pe, NULL);
+ if (ret > 0 && ret != EEH_STATE_NOT_SUPPORT)
+ enable = 1;
+
+ if (enable) {
+ eeh_subsystem_enabled = 1;
+ eeh_add_to_parent_pe(edev);
+
+ pr_debug("%s: EEH enabled on %s PHB#%d-PE#%x, config addr#%x\n",
+ __func__, dn->full_name, pe.phb->global_number,
+ pe.addr, pe.config_addr);
+ } else if (dn->parent && of_node_to_eeh_dev(dn->parent) &&
+ (of_node_to_eeh_dev(dn->parent))->pe) {
+ /* This device doesn't support EEH, but it may have an
+ * EEH parent, in which case we mark it as supported.
+ */
+ edev->config_addr = of_node_to_eeh_dev(dn->parent)->config_addr;
+ edev->pe_config_addr = of_node_to_eeh_dev(dn->parent)->pe_config_addr;
+ eeh_add_to_parent_pe(edev);
+ }
+ }
+
+ /* Save memory bars */
+ eeh_save_bars(edev);
+
+ return NULL;
+}
+
/**
* pseries_eeh_set_option - Initialize EEH or MMIO/DMA reenable
- * @dn: device node
+ * @pe: EEH PE
* @option: operation to be issued
*
* The function is used to control the EEH functionality globally.
* Currently, following options are support according to PAPR:
* Enable EEH, Disable EEH, Enable MMIO and Enable DMA
*/
-static int pseries_eeh_set_option(struct device_node *dn, int option)
+static int pseries_eeh_set_option(struct eeh_pe *pe, int option)
{
int ret = 0;
- struct eeh_dev *edev;
- const u32 *reg;
int config_addr;
- edev = of_node_to_eeh_dev(dn);
-
/*
* When we're enabling or disabling EEH functioality on
* the particular PE, the PE config address is possibly
switch (option) {
case EEH_OPT_DISABLE:
case EEH_OPT_ENABLE:
- reg = of_get_property(dn, "reg", NULL);
- config_addr = reg[0];
- break;
-
case EEH_OPT_THAW_MMIO:
case EEH_OPT_THAW_DMA:
- config_addr = edev->config_addr;
- if (edev->pe_config_addr)
- config_addr = edev->pe_config_addr;
+ config_addr = pe->config_addr;
+ if (pe->addr)
+ config_addr = pe->addr;
break;
default:
}
ret = rtas_call(ibm_set_eeh_option, 4, 1, NULL,
- config_addr, BUID_HI(edev->phb->buid),
- BUID_LO(edev->phb->buid), option);
+ config_addr, BUID_HI(pe->phb->buid),
+ BUID_LO(pe->phb->buid), option);
return ret;
}
/**
* pseries_eeh_get_pe_addr - Retrieve PE address
- * @dn: device node
+ * @pe: EEH PE
*
* Retrieve the assocated PE address. Actually, there're 2 RTAS
* function calls dedicated for the purpose. We need implement
* It's notable that zero'ed return value means invalid PE config
* address.
*/
-static int pseries_eeh_get_pe_addr(struct device_node *dn)
+static int pseries_eeh_get_pe_addr(struct eeh_pe *pe)
{
- struct eeh_dev *edev;
int ret = 0;
int rets[3];
- edev = of_node_to_eeh_dev(dn);
-
if (ibm_get_config_addr_info2 != RTAS_UNKNOWN_SERVICE) {
/*
* First of all, we need to make sure there has one PE
* meaningless.
*/
ret = rtas_call(ibm_get_config_addr_info2, 4, 2, rets,
- edev->config_addr, BUID_HI(edev->phb->buid),
- BUID_LO(edev->phb->buid), 1);
+ pe->config_addr, BUID_HI(pe->phb->buid),
+ BUID_LO(pe->phb->buid), 1);
if (ret || (rets[0] == 0))
return 0;
/* Retrieve the associated PE config address */
ret = rtas_call(ibm_get_config_addr_info2, 4, 2, rets,
- edev->config_addr, BUID_HI(edev->phb->buid),
- BUID_LO(edev->phb->buid), 0);
+ pe->config_addr, BUID_HI(pe->phb->buid),
+ BUID_LO(pe->phb->buid), 0);
if (ret) {
- pr_warning("%s: Failed to get PE address for %s\n",
- __func__, dn->full_name);
+ pr_warning("%s: Failed to get address for PHB#%d-PE#%x\n",
+ __func__, pe->phb->global_number, pe->config_addr);
return 0;
}
if (ibm_get_config_addr_info != RTAS_UNKNOWN_SERVICE) {
ret = rtas_call(ibm_get_config_addr_info, 4, 2, rets,
- edev->config_addr, BUID_HI(edev->phb->buid),
- BUID_LO(edev->phb->buid), 0);
+ pe->config_addr, BUID_HI(pe->phb->buid),
+ BUID_LO(pe->phb->buid), 0);
if (ret) {
- pr_warning("%s: Failed to get PE address for %s\n",
- __func__, dn->full_name);
+ pr_warning("%s: Failed to get address for PHB#%d-PE#%x\n",
+ __func__, pe->phb->global_number, pe->config_addr);
return 0;
}
/**
* pseries_eeh_get_state - Retrieve PE state
- * @dn: PE associated device node
+ * @pe: EEH PE
* @state: return value
*
* Retrieve the state of the specified PE. On RTAS compliant
* RTAS calls for the purpose, we need to try the new one and back
* to the old one if the new one couldn't work properly.
*/
-static int pseries_eeh_get_state(struct device_node *dn, int *state)
+static int pseries_eeh_get_state(struct eeh_pe *pe, int *state)
{
- struct eeh_dev *edev;
int config_addr;
int ret;
int rets[4];
int result;
/* Figure out PE config address if possible */
- edev = of_node_to_eeh_dev(dn);
- config_addr = edev->config_addr;
- if (edev->pe_config_addr)
- config_addr = edev->pe_config_addr;
+ config_addr = pe->config_addr;
+ if (pe->addr)
+ config_addr = pe->addr;
if (ibm_read_slot_reset_state2 != RTAS_UNKNOWN_SERVICE) {
ret = rtas_call(ibm_read_slot_reset_state2, 3, 4, rets,
- config_addr, BUID_HI(edev->phb->buid),
- BUID_LO(edev->phb->buid));
+ config_addr, BUID_HI(pe->phb->buid),
+ BUID_LO(pe->phb->buid));
} else if (ibm_read_slot_reset_state != RTAS_UNKNOWN_SERVICE) {
/* Fake PE unavailable info */
rets[2] = 0;
ret = rtas_call(ibm_read_slot_reset_state, 3, 3, rets,
- config_addr, BUID_HI(edev->phb->buid),
- BUID_LO(edev->phb->buid));
+ config_addr, BUID_HI(pe->phb->buid),
+ BUID_LO(pe->phb->buid));
} else {
return EEH_STATE_NOT_SUPPORT;
}
/**
* pseries_eeh_reset - Reset the specified PE
- * @dn: PE associated device node
+ * @pe: EEH PE
* @option: reset option
*
* Reset the specified PE
*/
-static int pseries_eeh_reset(struct device_node *dn, int option)
+static int pseries_eeh_reset(struct eeh_pe *pe, int option)
{
- struct eeh_dev *edev;
int config_addr;
int ret;
/* Figure out PE address */
- edev = of_node_to_eeh_dev(dn);
- config_addr = edev->config_addr;
- if (edev->pe_config_addr)
- config_addr = edev->pe_config_addr;
+ config_addr = pe->config_addr;
+ if (pe->addr)
+ config_addr = pe->addr;
/* Reset PE through RTAS call */
ret = rtas_call(ibm_set_slot_reset, 4, 1, NULL,
- config_addr, BUID_HI(edev->phb->buid),
- BUID_LO(edev->phb->buid), option);
+ config_addr, BUID_HI(pe->phb->buid),
+ BUID_LO(pe->phb->buid), option);
/* If fundamental-reset not supported, try hot-reset */
if (option == EEH_RESET_FUNDAMENTAL &&
ret == -8) {
ret = rtas_call(ibm_set_slot_reset, 4, 1, NULL,
- config_addr, BUID_HI(edev->phb->buid),
- BUID_LO(edev->phb->buid), EEH_RESET_HOT);
+ config_addr, BUID_HI(pe->phb->buid),
+ BUID_LO(pe->phb->buid), EEH_RESET_HOT);
}
return ret;
/**
* pseries_eeh_wait_state - Wait for PE state
- * @dn: PE associated device node
+ * @pe: EEH PE
* @max_wait: maximal period in microsecond
*
* Wait for the state of associated PE. It might take some time
* to retrieve the PE's state.
*/
-static int pseries_eeh_wait_state(struct device_node *dn, int max_wait)
+static int pseries_eeh_wait_state(struct eeh_pe *pe, int max_wait)
{
int ret;
int mwait;
#define EEH_STATE_MAX_WAIT_TIME (300 * 1000)
while (1) {
- ret = pseries_eeh_get_state(dn, &mwait);
+ ret = pseries_eeh_get_state(pe, &mwait);
/*
* If the PE's state is temporarily unavailable,
/**
* pseries_eeh_get_log - Retrieve error log
- * @dn: device node
+ * @pe: EEH PE
* @severity: temporary or permanent error log
* @drv_log: driver log to be combined with retrieved error log
* @len: length of driver log
* Actually, the error will be retrieved through the dedicated
* RTAS call.
*/
-static int pseries_eeh_get_log(struct device_node *dn, int severity, char *drv_log, unsigned long len)
+static int pseries_eeh_get_log(struct eeh_pe *pe, int severity, char *drv_log, unsigned long len)
{
- struct eeh_dev *edev;
int config_addr;
unsigned long flags;
int ret;
- edev = of_node_to_eeh_dev(dn);
spin_lock_irqsave(&slot_errbuf_lock, flags);
memset(slot_errbuf, 0, eeh_error_buf_size);
/* Figure out the PE address */
- config_addr = edev->config_addr;
- if (edev->pe_config_addr)
- config_addr = edev->pe_config_addr;
+ config_addr = pe->config_addr;
+ if (pe->addr)
+ config_addr = pe->addr;
ret = rtas_call(ibm_slot_error_detail, 8, 1, NULL, config_addr,
- BUID_HI(edev->phb->buid), BUID_LO(edev->phb->buid),
+ BUID_HI(pe->phb->buid), BUID_LO(pe->phb->buid),
virt_to_phys(drv_log), len,
virt_to_phys(slot_errbuf), eeh_error_buf_size,
severity);
/**
* pseries_eeh_configure_bridge - Configure PCI bridges in the indicated PE
- * @dn: PE associated device node
+ * @pe: EEH PE
*
* The function will be called to reconfigure the bridges included
* in the specified PE so that the mulfunctional PE would be recovered
* again.
*/
-static int pseries_eeh_configure_bridge(struct device_node *dn)
+static int pseries_eeh_configure_bridge(struct eeh_pe *pe)
{
- struct eeh_dev *edev;
int config_addr;
int ret;
/* Figure out the PE address */
- edev = of_node_to_eeh_dev(dn);
- config_addr = edev->config_addr;
- if (edev->pe_config_addr)
- config_addr = edev->pe_config_addr;
+ config_addr = pe->config_addr;
+ if (pe->addr)
+ config_addr = pe->addr;
/* Use new configure-pe function, if supported */
if (ibm_configure_pe != RTAS_UNKNOWN_SERVICE) {
ret = rtas_call(ibm_configure_pe, 3, 1, NULL,
- config_addr, BUID_HI(edev->phb->buid),
- BUID_LO(edev->phb->buid));
+ config_addr, BUID_HI(pe->phb->buid),
+ BUID_LO(pe->phb->buid));
} else if (ibm_configure_bridge != RTAS_UNKNOWN_SERVICE) {
ret = rtas_call(ibm_configure_bridge, 3, 1, NULL,
- config_addr, BUID_HI(edev->phb->buid),
- BUID_LO(edev->phb->buid));
+ config_addr, BUID_HI(pe->phb->buid),
+ BUID_LO(pe->phb->buid));
} else {
return -EFAULT;
}
if (ret)
- pr_warning("%s: Unable to configure bridge %d for %s\n",
- __func__, ret, dn->full_name);
+ pr_warning("%s: Unable to configure bridge PHB#%d-PE#%x (%d)\n",
+ __func__, pe->phb->global_number, pe->addr, ret);
return ret;
}
static struct eeh_ops pseries_eeh_ops = {
.name = "pseries",
.init = pseries_eeh_init,
+ .of_probe = pseries_eeh_of_probe,
+ .dev_probe = NULL,
.set_option = pseries_eeh_set_option,
.get_pe_addr = pseries_eeh_get_pe_addr,
.get_state = pseries_eeh_get_state,
git.samba.org / sfrench / cifs-2.6.git / blobdiff