+- clocks: Phandle and clock specifiers for each entry in clock-names, in the
+ same order. See ../clock/clock-bindings.txt.
+- clock-names: May contain any/all of the following depending on the IP
+ configuration, in any order:
+ - "tx"
+ The EQOS transmit path clock. The HW signal name is clk_tx_i.
+ In some configurations (e.g. GMII/RGMII), this clock also drives the PHY TX
+ path. In other configurations, other clocks (such as tx_125, rmii) may
+ drive the PHY TX path.
+ - "rx"
+ The EQOS receive path clock. The HW signal name is clk_rx_i.
+ In some configurations (e.g. GMII/RGMII), this clock is derived from the
+ PHY's RX clock output. In other configurations, other clocks (such as
+ rx_125, rmii) may drive the EQOS RX path.
+ In cases where the PHY clock is directly fed into the EQOS receive path
+ without intervening logic, the DT need not represent this clock, since it
+ is assumed to be fully under the control of the PHY device/driver. In
+ cases where SoC integration adds additional logic to this path, such as a
+ SW-controlled clock gate, this clock should be represented in DT.
+ - "slave_bus"
+ The CPU/slave-bus (CSR) interface clock. This applies to any bus type;
+ APB, AHB, AXI, etc. The HW signal name is hclk_i (AHB) or clk_csr_i (other
+ buses).
+ - "master_bus"
+ The master bus interface clock. Only required in configurations that use a
+ separate clock for the master and slave bus interfaces. The HW signal name
+ is hclk_i (AHB) or aclk_i (AXI).
+ - "ptp_ref"
+ The PTP reference clock. The HW signal name is clk_ptp_ref_i.
+ - "phy_ref_clk"
+ This clock is deprecated and should not be used by new compatible values.
+ It is equivalent to "tx".
+ - "apb_pclk"
+ This clock is deprecated and should not be used by new compatible values.
+ It is equivalent to "slave_bus".
+
+ Note: Support for additional IP configurations may require adding the
+ following clocks to this list in the future: clk_rx_125_i, clk_tx_125_i,
+ clk_pmarx_0_i, clk_pmarx1_i, clk_rmii_i, clk_revmii_rx_i, clk_revmii_tx_i.
+ Configurations exist where multiple similar clocks are used at once, e.g. all
+ of clk_rx_125_i, clk_pmarx_0_i, clk_pmarx1_i. For this reason it is best to
+ extend the binding with a separate clock-names entry for each of those RX
+ clocks, rather than repurposing the existing "rx" clock-names entry as a
+ generic/logical clock in a similar fashion to "master_bus" and "slave_bus".
+ This will allow easy support for configurations that support multiple PHY
+ interfaces using a mux, and hence need to have explicit control over
+ specific RX clocks.
+
+ The following compatible values require the following set of clocks:
+ - "nvidia,tegra186-eqos", "snps,dwc-qos-ethernet-4.10":
+ - "slave_bus"
+ - "master_bus"
+ - "rx"
+ - "tx"
+ - "ptp_ref"
+ - "axis,artpec6-eqos", "snps,dwc-qos-ethernet-4.10":
+ - "slave_bus"
+ - "master_bus"
+ - "tx"
+ - "ptp_ref"
+ - "snps,dwc-qos-ethernet-4.10" (deprecated):
+ - "phy_ref_clk"
+ - "apb_clk"