drivers/usb/host/xhci-rcar.c

   1 // SPDX-License-Identifier: GPL-2.0
   2 /*
   3  * xHCI host controller driver for R-Car SoCs
   4  *
   5  * Copyright (C) 2014 Renesas Electronics Corporation
   6  */
   7
   8 #include <linux/firmware.h>
   9 #include <linux/module.h>
  10 #include <linux/platform_device.h>
  11 #include <linux/of.h>
  12 #include <linux/usb/phy.h>
  13 #include <linux/sys_soc.h>
  14
  15 #include "xhci.h"
  16 #include "xhci-plat.h"
  17 #include "xhci-rcar.h"
  18
  19 /*
  20 * - The V3 firmware is for r8a7796 (with good performance) and r8a7795 es2.0
  21 *   or later.
  22 * - The V2 firmware can be used on both r8a7795 (es1.x) and r8a7796.
  23 * - The V2 firmware is possible to use on R-Car Gen2. However, the V2 causes
  24 *   performance degradation. So, this driver continues to use the V1 if R-Car
  25 *   Gen2.
  26 * - The V1 firmware is impossible to use on R-Car Gen3.
  27 */
  28 MODULE_FIRMWARE(XHCI_RCAR_FIRMWARE_NAME_V1);
  29 MODULE_FIRMWARE(XHCI_RCAR_FIRMWARE_NAME_V2);
  30 MODULE_FIRMWARE(XHCI_RCAR_FIRMWARE_NAME_V3);
  31
  32 /*** Register Offset ***/
  33 #define RCAR_USB3_INT_ENA       0x224   /* Interrupt Enable */
  34 #define RCAR_USB3_DL_CTRL       0x250   /* FW Download Control & Status */
  35 #define RCAR_USB3_FW_DATA0      0x258   /* FW Data0 */
  36
  37 #define RCAR_USB3_LCLK          0xa44   /* LCLK Select */
  38 #define RCAR_USB3_CONF1         0xa48   /* USB3.0 Configuration1 */
  39 #define RCAR_USB3_CONF2         0xa5c   /* USB3.0 Configuration2 */
  40 #define RCAR_USB3_CONF3         0xaa8   /* USB3.0 Configuration3 */
  41 #define RCAR_USB3_RX_POL        0xab0   /* USB3.0 RX Polarity */
  42 #define RCAR_USB3_TX_POL        0xab8   /* USB3.0 TX Polarity */
  43
  44 /*** Register Settings ***/
  45 /* Interrupt Enable */
  46 #define RCAR_USB3_INT_XHC_ENA   0x00000001
  47 #define RCAR_USB3_INT_PME_ENA   0x00000002
  48 #define RCAR_USB3_INT_HSE_ENA   0x00000004
  49 #define RCAR_USB3_INT_ENA_VAL   (RCAR_USB3_INT_XHC_ENA | \
  50                                 RCAR_USB3_INT_PME_ENA | RCAR_USB3_INT_HSE_ENA)
  51
  52 /* FW Download Control & Status */
  53 #define RCAR_USB3_DL_CTRL_ENABLE        0x00000001
  54 #define RCAR_USB3_DL_CTRL_FW_SUCCESS    0x00000010
  55 #define RCAR_USB3_DL_CTRL_FW_SET_DATA0  0x00000100
  56
  57 /* LCLK Select */
  58 #define RCAR_USB3_LCLK_ENA_VAL  0x01030001
  59
  60 /* USB3.0 Configuration */
  61 #define RCAR_USB3_CONF1_VAL     0x00030204
  62 #define RCAR_USB3_CONF2_VAL     0x00030300
  63 #define RCAR_USB3_CONF3_VAL     0x13802007
  64
  65 /* USB3.0 Polarity */
  66 #define RCAR_USB3_RX_POL_VAL    BIT(21)
  67 #define RCAR_USB3_TX_POL_VAL    BIT(4)
  68
  69 /* For soc_device_attribute */
  70 #define RCAR_XHCI_FIRMWARE_V2   BIT(0) /* FIRMWARE V2 */
  71 #define RCAR_XHCI_FIRMWARE_V3   BIT(1) /* FIRMWARE V3 */
  72
  73 static const struct soc_device_attribute rcar_quirks_match[]  = {
  74         {
  75                 .soc_id = "r8a7795", .revision = "ES1.*",
  76                 .data = (void *)RCAR_XHCI_FIRMWARE_V2,
  77         },
  78         {
  79                 .soc_id = "r8a7795",
  80                 .data = (void *)RCAR_XHCI_FIRMWARE_V3,
  81         },
  82         {
  83                 .soc_id = "r8a7796",
  84                 .data = (void *)RCAR_XHCI_FIRMWARE_V3,
  85         },
  86         { /* sentinel */ },
  87 };
  88
  89 static void xhci_rcar_start_gen2(struct usb_hcd *hcd)
  90 {
  91         /* LCLK Select */
  92         writel(RCAR_USB3_LCLK_ENA_VAL, hcd->regs + RCAR_USB3_LCLK);
  93         /* USB3.0 Configuration */
  94         writel(RCAR_USB3_CONF1_VAL, hcd->regs + RCAR_USB3_CONF1);
  95         writel(RCAR_USB3_CONF2_VAL, hcd->regs + RCAR_USB3_CONF2);
  96         writel(RCAR_USB3_CONF3_VAL, hcd->regs + RCAR_USB3_CONF3);
  97         /* USB3.0 Polarity */
  98         writel(RCAR_USB3_RX_POL_VAL, hcd->regs + RCAR_USB3_RX_POL);
  99         writel(RCAR_USB3_TX_POL_VAL, hcd->regs + RCAR_USB3_TX_POL);
 100 }
 101
 102 static int xhci_rcar_is_gen2(struct device *dev)
 103 {
 104         struct device_node *node = dev->of_node;
 105
 106         return of_device_is_compatible(node, "renesas,xhci-r8a7790") ||
 107                 of_device_is_compatible(node, "renesas,xhci-r8a7791") ||
 108                 of_device_is_compatible(node, "renesas,xhci-r8a7793") ||
 109                 of_device_is_compatible(node, "renensas,rcar-gen2-xhci");
 110 }
 111
 112 static int xhci_rcar_is_gen3(struct device *dev)
 113 {
 114         struct device_node *node = dev->of_node;
 115
 116         return of_device_is_compatible(node, "renesas,xhci-r8a7795") ||
 117                 of_device_is_compatible(node, "renesas,xhci-r8a7796") ||
 118                 of_device_is_compatible(node, "renesas,rcar-gen3-xhci");
 119 }
 120
 121 void xhci_rcar_start(struct usb_hcd *hcd)
 122 {
 123         u32 temp;
 124
 125         if (hcd->regs != NULL) {
 126                 /* Interrupt Enable */
 127                 temp = readl(hcd->regs + RCAR_USB3_INT_ENA);
 128                 temp |= RCAR_USB3_INT_ENA_VAL;
 129                 writel(temp, hcd->regs + RCAR_USB3_INT_ENA);
 130                 if (xhci_rcar_is_gen2(hcd->self.controller))
 131                         xhci_rcar_start_gen2(hcd);
 132         }
 133 }
 134
 135 static int xhci_rcar_download_firmware(struct usb_hcd *hcd)
 136 {
 137         struct device *dev = hcd->self.controller;
 138         void __iomem *regs = hcd->regs;
 139         struct xhci_plat_priv *priv = hcd_to_xhci_priv(hcd);
 140         const struct firmware *fw;
 141         int retval, index, j, time;
 142         int timeout = 10000;
 143         u32 data, val, temp;
 144         u32 quirks = 0;
 145         const struct soc_device_attribute *attr;
 146         const char *firmware_name;
 147
 148         attr = soc_device_match(rcar_quirks_match);
 149         if (attr)
 150                 quirks = (uintptr_t)attr->data;
 151
 152         if (quirks & RCAR_XHCI_FIRMWARE_V2)
 153                 firmware_name = XHCI_RCAR_FIRMWARE_NAME_V2;
 154         else if (quirks & RCAR_XHCI_FIRMWARE_V3)
 155                 firmware_name = XHCI_RCAR_FIRMWARE_NAME_V3;
 156         else
 157                 firmware_name = priv->firmware_name;
 158
 159         /* request R-Car USB3.0 firmware */
 160         retval = request_firmware(&fw, firmware_name, dev);
 161         if (retval)
 162                 return retval;
 163
 164         /* download R-Car USB3.0 firmware */
 165         temp = readl(regs + RCAR_USB3_DL_CTRL);
 166         temp |= RCAR_USB3_DL_CTRL_ENABLE;
 167         writel(temp, regs + RCAR_USB3_DL_CTRL);
 168
 169         for (index = 0; index < fw->size; index += 4) {
 170                 /* to avoid reading beyond the end of the buffer */
 171                 for (data = 0, j = 3; j >= 0; j--) {
 172                         if ((j + index) < fw->size)
 173                                 data |= fw->data[index + j] << (8 * j);
 174                 }
 175                 writel(data, regs + RCAR_USB3_FW_DATA0);
 176                 temp = readl(regs + RCAR_USB3_DL_CTRL);
 177                 temp |= RCAR_USB3_DL_CTRL_FW_SET_DATA0;
 178                 writel(temp, regs + RCAR_USB3_DL_CTRL);
 179
 180                 for (time = 0; time < timeout; time++) {
 181                         val = readl(regs + RCAR_USB3_DL_CTRL);
 182                         if ((val & RCAR_USB3_DL_CTRL_FW_SET_DATA0) == 0)
 183                                 break;
 184                         udelay(1);
 185                 }
 186                 if (time == timeout) {
 187                         retval = -ETIMEDOUT;
 188                         break;
 189                 }
 190         }
 191
 192         temp = readl(regs + RCAR_USB3_DL_CTRL);
 193         temp &= ~RCAR_USB3_DL_CTRL_ENABLE;
 194         writel(temp, regs + RCAR_USB3_DL_CTRL);
 195
 196         for (time = 0; time < timeout; time++) {
 197                 val = readl(regs + RCAR_USB3_DL_CTRL);
 198                 if (val & RCAR_USB3_DL_CTRL_FW_SUCCESS) {
 199                         retval = 0;
 200                         break;
 201                 }
 202                 udelay(1);
 203         }
 204         if (time == timeout)
 205                 retval = -ETIMEDOUT;
 206
 207         release_firmware(fw);
 208
 209         return retval;
 210 }
 211
 212 /* This function needs to initialize a "phy" of usb before */
 213 int xhci_rcar_init_quirk(struct usb_hcd *hcd)
 214 {
 215         struct xhci_hcd *xhci = hcd_to_xhci(hcd);
 216
 217         /* If hcd->regs is NULL, we don't just call the following function */
 218         if (!hcd->regs)
 219                 return 0;
 220
 221         /*
 222          * On R-Car Gen2 and Gen3, the AC64 bit (bit 0) of HCCPARAMS1 is set
 223          * to 1. However, these SoCs don't support 64-bit address memory
 224          * pointers. So, this driver clears the AC64 bit of xhci->hcc_params
 225          * to call dma_set_coherent_mask(dev, DMA_BIT_MASK(32)) in
 226          * xhci_gen_setup().
 227          */
 228         if (xhci_rcar_is_gen2(hcd->self.controller) ||
 229                         xhci_rcar_is_gen3(hcd->self.controller))
 230                 xhci->quirks |= XHCI_NO_64BIT_SUPPORT;
 231
 232         return xhci_rcar_download_firmware(hcd);
 233 }
 234
 235 int xhci_rcar_resume_quirk(struct usb_hcd *hcd)
 236 {
 237         int ret;
 238
 239         ret = xhci_rcar_download_firmware(hcd);
 240         if (!ret)
 241                 xhci_rcar_start(hcd);
 242
 243         return ret;
 244 }