Merge tag 'net-6.0-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net

[sfrench/cifs-2.6.git] / drivers / net / ethernet / freescale / fec.h

/* SPDX-License-Identifier: GPL-2.0 */
/****************************************************************************/

/*
 *      fec.h  --  Fast Ethernet Controller for Motorola ColdFire SoC
 *                 processors.
 *
 *      (C) Copyright 2000-2005, Greg Ungerer (gerg@snapgear.com)
 *      (C) Copyright 2000-2001, Lineo (www.lineo.com)
 */

/****************************************************************************/
#ifndef FEC_H
#define FEC_H
/****************************************************************************/

#include <linux/clocksource.h>
#include <linux/net_tstamp.h>
#include <linux/pm_qos.h>
#include <linux/ptp_clock_kernel.h>
#include <linux/timecounter.h>

#if defined(CONFIG_M523x) || defined(CONFIG_M527x) || defined(CONFIG_M528x) || \
    defined(CONFIG_M520x) || defined(CONFIG_M532x) || defined(CONFIG_ARM) || \
    defined(CONFIG_ARM64) || defined(CONFIG_COMPILE_TEST)
/*
 *      Just figures, Motorola would have to change the offsets for
 *      registers in the same peripheral device on different models
 *      of the ColdFire!
 */
#define FEC_IEVENT              0x004 /* Interrupt event reg */
#define FEC_IMASK               0x008 /* Interrupt mask reg */
#define FEC_R_DES_ACTIVE_0      0x010 /* Receive descriptor reg */
#define FEC_X_DES_ACTIVE_0      0x014 /* Transmit descriptor reg */
#define FEC_ECNTRL              0x024 /* Ethernet control reg */
#define FEC_MII_DATA            0x040 /* MII manage frame reg */
#define FEC_MII_SPEED           0x044 /* MII speed control reg */
#define FEC_MIB_CTRLSTAT        0x064 /* MIB control/status reg */
#define FEC_R_CNTRL             0x084 /* Receive control reg */
#define FEC_X_CNTRL             0x0c4 /* Transmit Control reg */
#define FEC_ADDR_LOW            0x0e4 /* Low 32bits MAC address */
#define FEC_ADDR_HIGH           0x0e8 /* High 16bits MAC address */
#define FEC_OPD                 0x0ec /* Opcode + Pause duration */
#define FEC_TXIC0               0x0f0 /* Tx Interrupt Coalescing for ring 0 */
#define FEC_TXIC1               0x0f4 /* Tx Interrupt Coalescing for ring 1 */
#define FEC_TXIC2               0x0f8 /* Tx Interrupt Coalescing for ring 2 */
#define FEC_RXIC0               0x100 /* Rx Interrupt Coalescing for ring 0 */
#define FEC_RXIC1               0x104 /* Rx Interrupt Coalescing for ring 1 */
#define FEC_RXIC2               0x108 /* Rx Interrupt Coalescing for ring 2 */
#define FEC_HASH_TABLE_HIGH     0x118 /* High 32bits hash table */
#define FEC_HASH_TABLE_LOW      0x11c /* Low 32bits hash table */
#define FEC_GRP_HASH_TABLE_HIGH 0x120 /* High 32bits hash table */
#define FEC_GRP_HASH_TABLE_LOW  0x124 /* Low 32bits hash table */
#define FEC_X_WMRK              0x144 /* FIFO transmit water mark */
#define FEC_R_BOUND             0x14c /* FIFO receive bound reg */
#define FEC_R_FSTART            0x150 /* FIFO receive start reg */
#define FEC_R_DES_START_1       0x160 /* Receive descriptor ring 1 */
#define FEC_X_DES_START_1       0x164 /* Transmit descriptor ring 1 */
#define FEC_R_BUFF_SIZE_1       0x168 /* Maximum receive buff ring1 size */
#define FEC_R_DES_START_2       0x16c /* Receive descriptor ring 2 */
#define FEC_X_DES_START_2       0x170 /* Transmit descriptor ring 2 */
#define FEC_R_BUFF_SIZE_2       0x174 /* Maximum receive buff ring2 size */
#define FEC_R_DES_START_0       0x180 /* Receive descriptor ring */
#define FEC_X_DES_START_0       0x184 /* Transmit descriptor ring */
#define FEC_R_BUFF_SIZE_0       0x188 /* Maximum receive buff size */
#define FEC_R_FIFO_RSFL         0x190 /* Receive FIFO section full threshold */
#define FEC_R_FIFO_RSEM         0x194 /* Receive FIFO section empty threshold */
#define FEC_R_FIFO_RAEM         0x198 /* Receive FIFO almost empty threshold */
#define FEC_R_FIFO_RAFL         0x19c /* Receive FIFO almost full threshold */
#define FEC_FTRL                0x1b0 /* Frame truncation receive length*/
#define FEC_RACC                0x1c4 /* Receive Accelerator function */
#define FEC_RCMR_1              0x1c8 /* Receive classification match ring 1 */
#define FEC_RCMR_2              0x1cc /* Receive classification match ring 2 */
#define FEC_DMA_CFG_1           0x1d8 /* DMA class configuration for ring 1 */
#define FEC_DMA_CFG_2           0x1dc /* DMA class Configuration for ring 2 */
#define FEC_R_DES_ACTIVE_1      0x1e0 /* Rx descriptor active for ring 1 */
#define FEC_X_DES_ACTIVE_1      0x1e4 /* Tx descriptor active for ring 1 */
#define FEC_R_DES_ACTIVE_2      0x1e8 /* Rx descriptor active for ring 2 */
#define FEC_X_DES_ACTIVE_2      0x1ec /* Tx descriptor active for ring 2 */
#define FEC_QOS_SCHEME          0x1f0 /* Set multi queues Qos scheme */
#define FEC_LPI_SLEEP           0x1f4 /* Set IEEE802.3az LPI Sleep Ts time */
#define FEC_LPI_WAKE            0x1f8 /* Set IEEE802.3az LPI Wake Tw time */
#define FEC_MIIGSK_CFGR         0x300 /* MIIGSK Configuration reg */
#define FEC_MIIGSK_ENR          0x308 /* MIIGSK Enable reg */

#define BM_MIIGSK_CFGR_MII              0x00
#define BM_MIIGSK_CFGR_RMII             0x01
#define BM_MIIGSK_CFGR_FRCONT_10M       0x40

#define RMON_T_DROP             0x200 /* Count of frames not cntd correctly */
#define RMON_T_PACKETS          0x204 /* RMON TX packet count */
#define RMON_T_BC_PKT           0x208 /* RMON TX broadcast pkts */
#define RMON_T_MC_PKT           0x20c /* RMON TX multicast pkts */
#define RMON_T_CRC_ALIGN        0x210 /* RMON TX pkts with CRC align err */
#define RMON_T_UNDERSIZE        0x214 /* RMON TX pkts < 64 bytes, good CRC */
#define RMON_T_OVERSIZE         0x218 /* RMON TX pkts > MAX_FL bytes good CRC */
#define RMON_T_FRAG             0x21c /* RMON TX pkts < 64 bytes, bad CRC */
#define RMON_T_JAB              0x220 /* RMON TX pkts > MAX_FL bytes, bad CRC */
#define RMON_T_COL              0x224 /* RMON TX collision count */
#define RMON_T_P64              0x228 /* RMON TX 64 byte pkts */
#define RMON_T_P65TO127         0x22c /* RMON TX 65 to 127 byte pkts */
#define RMON_T_P128TO255        0x230 /* RMON TX 128 to 255 byte pkts */
#define RMON_T_P256TO511        0x234 /* RMON TX 256 to 511 byte pkts */
#define RMON_T_P512TO1023       0x238 /* RMON TX 512 to 1023 byte pkts */
#define RMON_T_P1024TO2047      0x23c /* RMON TX 1024 to 2047 byte pkts */
#define RMON_T_P_GTE2048        0x240 /* RMON TX pkts > 2048 bytes */
#define RMON_T_OCTETS           0x244 /* RMON TX octets */
#define IEEE_T_DROP             0x248 /* Count of frames not counted crtly */
#define IEEE_T_FRAME_OK         0x24c /* Frames tx'd OK */
#define IEEE_T_1COL             0x250 /* Frames tx'd with single collision */
#define IEEE_T_MCOL             0x254 /* Frames tx'd with multiple collision */
#define IEEE_T_DEF              0x258 /* Frames tx'd after deferral delay */
#define IEEE_T_LCOL             0x25c /* Frames tx'd with late collision */
#define IEEE_T_EXCOL            0x260 /* Frames tx'd with excesv collisions */
#define IEEE_T_MACERR           0x264 /* Frames tx'd with TX FIFO underrun */
#define IEEE_T_CSERR            0x268 /* Frames tx'd with carrier sense err */
#define IEEE_T_SQE              0x26c /* Frames tx'd with SQE err */
#define IEEE_T_FDXFC            0x270 /* Flow control pause frames tx'd */
#define IEEE_T_OCTETS_OK        0x274 /* Octet count for frames tx'd w/o err */
#define RMON_R_PACKETS          0x284 /* RMON RX packet count */
#define RMON_R_BC_PKT           0x288 /* RMON RX broadcast pkts */
#define RMON_R_MC_PKT           0x28c /* RMON RX multicast pkts */
#define RMON_R_CRC_ALIGN        0x290 /* RMON RX pkts with CRC alignment err */
#define RMON_R_UNDERSIZE        0x294 /* RMON RX pkts < 64 bytes, good CRC */
#define RMON_R_OVERSIZE         0x298 /* RMON RX pkts > MAX_FL bytes good CRC */
#define RMON_R_FRAG             0x29c /* RMON RX pkts < 64 bytes, bad CRC */
#define RMON_R_JAB              0x2a0 /* RMON RX pkts > MAX_FL bytes, bad CRC */
#define RMON_R_RESVD_O          0x2a4 /* Reserved */
#define RMON_R_P64              0x2a8 /* RMON RX 64 byte pkts */
#define RMON_R_P65TO127         0x2ac /* RMON RX 65 to 127 byte pkts */
#define RMON_R_P128TO255        0x2b0 /* RMON RX 128 to 255 byte pkts */
#define RMON_R_P256TO511        0x2b4 /* RMON RX 256 to 511 byte pkts */
#define RMON_R_P512TO1023       0x2b8 /* RMON RX 512 to 1023 byte pkts */
#define RMON_R_P1024TO2047      0x2bc /* RMON RX 1024 to 2047 byte pkts */
#define RMON_R_P_GTE2048        0x2c0 /* RMON RX pkts > 2048 bytes */
#define RMON_R_OCTETS           0x2c4 /* RMON RX octets */
#define IEEE_R_DROP             0x2c8 /* Count frames not counted correctly */
#define IEEE_R_FRAME_OK         0x2cc /* Frames rx'd OK */
#define IEEE_R_CRC              0x2d0 /* Frames rx'd with CRC err */
#define IEEE_R_ALIGN            0x2d4 /* Frames rx'd with alignment err */
#define IEEE_R_MACERR           0x2d8 /* Receive FIFO overflow count */
#define IEEE_R_FDXFC            0x2dc /* Flow control pause frames rx'd */
#define IEEE_R_OCTETS_OK        0x2e0 /* Octet cnt for frames rx'd w/o err */

#else

#define FEC_ECNTRL              0x000 /* Ethernet control reg */
#define FEC_IEVENT              0x004 /* Interrupt even reg */
#define FEC_IMASK               0x008 /* Interrupt mask reg */
#define FEC_IVEC                0x00c /* Interrupt vec status reg */
#define FEC_R_DES_ACTIVE_0      0x010 /* Receive descriptor reg */
#define FEC_R_DES_ACTIVE_1      FEC_R_DES_ACTIVE_0
#define FEC_R_DES_ACTIVE_2      FEC_R_DES_ACTIVE_0
#define FEC_X_DES_ACTIVE_0      0x014 /* Transmit descriptor reg */
#define FEC_X_DES_ACTIVE_1      FEC_X_DES_ACTIVE_0
#define FEC_X_DES_ACTIVE_2      FEC_X_DES_ACTIVE_0
#define FEC_MII_DATA            0x040 /* MII manage frame reg */
#define FEC_MII_SPEED           0x044 /* MII speed control reg */
#define FEC_R_BOUND             0x08c /* FIFO receive bound reg */
#define FEC_R_FSTART            0x090 /* FIFO receive start reg */
#define FEC_X_WMRK              0x0a4 /* FIFO transmit water mark */
#define FEC_X_FSTART            0x0ac /* FIFO transmit start reg */
#define FEC_R_CNTRL             0x104 /* Receive control reg */
#define FEC_MAX_FRM_LEN         0x108 /* Maximum frame length reg */
#define FEC_X_CNTRL             0x144 /* Transmit Control reg */
#define FEC_ADDR_LOW            0x3c0 /* Low 32bits MAC address */
#define FEC_ADDR_HIGH           0x3c4 /* High 16bits MAC address */
#define FEC_GRP_HASH_TABLE_HIGH 0x3c8 /* High 32bits hash table */
#define FEC_GRP_HASH_TABLE_LOW  0x3cc /* Low 32bits hash table */
#define FEC_R_DES_START_0       0x3d0 /* Receive descriptor ring */
#define FEC_R_DES_START_1       FEC_R_DES_START_0
#define FEC_R_DES_START_2       FEC_R_DES_START_0
#define FEC_X_DES_START_0       0x3d4 /* Transmit descriptor ring */
#define FEC_X_DES_START_1       FEC_X_DES_START_0
#define FEC_X_DES_START_2       FEC_X_DES_START_0
#define FEC_R_BUFF_SIZE_0       0x3d8 /* Maximum receive buff size */
#define FEC_R_BUFF_SIZE_1       FEC_R_BUFF_SIZE_0
#define FEC_R_BUFF_SIZE_2       FEC_R_BUFF_SIZE_0
#define FEC_FIFO_RAM            0x400 /* FIFO RAM buffer */
/* Not existed in real chip
 * Just for pass build.
 */
#define FEC_RCMR_1              0xfff
#define FEC_RCMR_2              0xfff
#define FEC_DMA_CFG_1           0xfff
#define FEC_DMA_CFG_2           0xfff
#define FEC_TXIC0               0xfff
#define FEC_TXIC1               0xfff
#define FEC_TXIC2               0xfff
#define FEC_RXIC0               0xfff
#define FEC_RXIC1               0xfff
#define FEC_RXIC2               0xfff
#define FEC_LPI_SLEEP           0xfff
#define FEC_LPI_WAKE            0xfff
#endif /* CONFIG_M5272 */


/*
 *      Define the buffer descriptor structure.
 *
 *      Evidently, ARM SoCs have the FEC block generated in a
 *      little endian mode so adjust endianness accordingly.
 */
#if defined(CONFIG_ARM) || defined(CONFIG_ARM64)
#define fec32_to_cpu le32_to_cpu
#define fec16_to_cpu le16_to_cpu
#define cpu_to_fec32 cpu_to_le32
#define cpu_to_fec16 cpu_to_le16
#define __fec32 __le32
#define __fec16 __le16

struct bufdesc {
        __fec16 cbd_datlen;     /* Data length */
        __fec16 cbd_sc;         /* Control and status info */
        __fec32 cbd_bufaddr;    /* Buffer address */
};
#else
#define fec32_to_cpu be32_to_cpu
#define fec16_to_cpu be16_to_cpu
#define cpu_to_fec32 cpu_to_be32
#define cpu_to_fec16 cpu_to_be16
#define __fec32 __be32
#define __fec16 __be16

struct bufdesc {
        __fec16 cbd_sc;         /* Control and status info */
        __fec16 cbd_datlen;     /* Data length */
        __fec32 cbd_bufaddr;    /* Buffer address */
};
#endif

struct bufdesc_ex {
        struct bufdesc desc;
        __fec32 cbd_esc;
        __fec32 cbd_prot;
        __fec32 cbd_bdu;
        __fec32 ts;
        __fec16 res0[4];
};

/*
 *      The following definitions courtesy of commproc.h, which where
 *      Copyright (c) 1997 Dan Malek (dmalek@jlc.net).
 */
#define BD_SC_EMPTY     ((ushort)0x8000)        /* Receive is empty */
#define BD_SC_READY     ((ushort)0x8000)        /* Transmit is ready */
#define BD_SC_WRAP      ((ushort)0x2000)        /* Last buffer descriptor */
#define BD_SC_INTRPT    ((ushort)0x1000)        /* Interrupt on change */
#define BD_SC_CM        ((ushort)0x0200)        /* Continuous mode */
#define BD_SC_ID        ((ushort)0x0100)        /* Rec'd too many idles */
#define BD_SC_P         ((ushort)0x0100)        /* xmt preamble */
#define BD_SC_BR        ((ushort)0x0020)        /* Break received */
#define BD_SC_FR        ((ushort)0x0010)        /* Framing error */
#define BD_SC_PR        ((ushort)0x0008)        /* Parity error */
#define BD_SC_OV        ((ushort)0x0002)        /* Overrun */
#define BD_SC_CD        ((ushort)0x0001)        /* ?? */

/* Buffer descriptor control/status used by Ethernet receive.
 */
#define BD_ENET_RX_EMPTY        ((ushort)0x8000)
#define BD_ENET_RX_WRAP         ((ushort)0x2000)
#define BD_ENET_RX_INTR         ((ushort)0x1000)
#define BD_ENET_RX_LAST         ((ushort)0x0800)
#define BD_ENET_RX_FIRST        ((ushort)0x0400)
#define BD_ENET_RX_MISS         ((ushort)0x0100)
#define BD_ENET_RX_LG           ((ushort)0x0020)
#define BD_ENET_RX_NO           ((ushort)0x0010)
#define BD_ENET_RX_SH           ((ushort)0x0008)
#define BD_ENET_RX_CR           ((ushort)0x0004)
#define BD_ENET_RX_OV           ((ushort)0x0002)
#define BD_ENET_RX_CL           ((ushort)0x0001)
#define BD_ENET_RX_STATS        ((ushort)0x013f)        /* All status bits */

/* Enhanced buffer descriptor control/status used by Ethernet receive */
#define BD_ENET_RX_VLAN         0x00000004

/* Buffer descriptor control/status used by Ethernet transmit.
 */
#define BD_ENET_TX_READY        ((ushort)0x8000)
#define BD_ENET_TX_PAD          ((ushort)0x4000)
#define BD_ENET_TX_WRAP         ((ushort)0x2000)
#define BD_ENET_TX_INTR         ((ushort)0x1000)
#define BD_ENET_TX_LAST         ((ushort)0x0800)
#define BD_ENET_TX_TC           ((ushort)0x0400)
#define BD_ENET_TX_DEF          ((ushort)0x0200)
#define BD_ENET_TX_HB           ((ushort)0x0100)
#define BD_ENET_TX_LC           ((ushort)0x0080)
#define BD_ENET_TX_RL           ((ushort)0x0040)
#define BD_ENET_TX_RCMASK       ((ushort)0x003c)
#define BD_ENET_TX_UN           ((ushort)0x0002)
#define BD_ENET_TX_CSL          ((ushort)0x0001)
#define BD_ENET_TX_STATS        ((ushort)0x0fff)        /* All status bits */

/* enhanced buffer descriptor control/status used by Ethernet transmit */
#define BD_ENET_TX_INT          0x40000000
#define BD_ENET_TX_TS           0x20000000
#define BD_ENET_TX_PINS         0x10000000
#define BD_ENET_TX_IINS         0x08000000


/* This device has up to three irqs on some platforms */
#define FEC_IRQ_NUM             3

/* Maximum number of queues supported
 * ENET with AVB IP can support up to 3 independent tx queues and rx queues.
 * User can point the queue number that is less than or equal to 3.
 */
#define FEC_ENET_MAX_TX_QS      3
#define FEC_ENET_MAX_RX_QS      3

#define FEC_R_DES_START(X)      (((X) == 1) ? FEC_R_DES_START_1 : \
                                (((X) == 2) ? \
                                        FEC_R_DES_START_2 : FEC_R_DES_START_0))
#define FEC_X_DES_START(X)      (((X) == 1) ? FEC_X_DES_START_1 : \
                                (((X) == 2) ? \
                                        FEC_X_DES_START_2 : FEC_X_DES_START_0))
#define FEC_R_BUFF_SIZE(X)      (((X) == 1) ? FEC_R_BUFF_SIZE_1 : \
                                (((X) == 2) ? \
                                        FEC_R_BUFF_SIZE_2 : FEC_R_BUFF_SIZE_0))

#define FEC_DMA_CFG(X)          (((X) == 2) ? FEC_DMA_CFG_2 : FEC_DMA_CFG_1)

#define DMA_CLASS_EN            (1 << 16)
#define FEC_RCMR(X)             (((X) == 2) ? FEC_RCMR_2 : FEC_RCMR_1)
#define IDLE_SLOPE_MASK         0xffff
#define IDLE_SLOPE_1            0x200 /* BW fraction: 0.5 */
#define IDLE_SLOPE_2            0x200 /* BW fraction: 0.5 */
#define IDLE_SLOPE(X)           (((X) == 1) ?                           \
                                (IDLE_SLOPE_1 & IDLE_SLOPE_MASK) :      \
                                (IDLE_SLOPE_2 & IDLE_SLOPE_MASK))
#define RCMR_MATCHEN            (0x1 << 16)
#define RCMR_CMP_CFG(v, n)      (((v) & 0x7) <<  (n << 2))
#define RCMR_CMP_1              (RCMR_CMP_CFG(0, 0) | RCMR_CMP_CFG(1, 1) | \
                                RCMR_CMP_CFG(2, 2) | RCMR_CMP_CFG(3, 3))
#define RCMR_CMP_2              (RCMR_CMP_CFG(4, 0) | RCMR_CMP_CFG(5, 1) | \
                                RCMR_CMP_CFG(6, 2) | RCMR_CMP_CFG(7, 3))
#define RCMR_CMP(X)             (((X) == 1) ? RCMR_CMP_1 : RCMR_CMP_2)
#define FEC_TX_BD_FTYPE(X)      (((X) & 0xf) << 20)

/* The number of Tx and Rx buffers.  These are allocated from the page
 * pool.  The code may assume these are power of two, so it it best
 * to keep them that size.
 * We don't need to allocate pages for the transmitter.  We just use
 * the skbuffer directly.
 */

#define FEC_ENET_RX_PAGES       256
#define FEC_ENET_RX_FRSIZE      2048
#define FEC_ENET_RX_FRPPG       (PAGE_SIZE / FEC_ENET_RX_FRSIZE)
#define RX_RING_SIZE            (FEC_ENET_RX_FRPPG * FEC_ENET_RX_PAGES)
#define FEC_ENET_TX_FRSIZE      2048
#define FEC_ENET_TX_FRPPG       (PAGE_SIZE / FEC_ENET_TX_FRSIZE)
#define TX_RING_SIZE            512     /* Must be power of two */
#define TX_RING_MOD_MASK        511     /*   for this to work */

#define BD_ENET_RX_INT          0x00800000
#define BD_ENET_RX_PTP          ((ushort)0x0400)
#define BD_ENET_RX_ICE          0x00000020
#define BD_ENET_RX_PCR          0x00000010
#define FLAG_RX_CSUM_ENABLED    (BD_ENET_RX_ICE | BD_ENET_RX_PCR)
#define FLAG_RX_CSUM_ERROR      (BD_ENET_RX_ICE | BD_ENET_RX_PCR)

/* Interrupt events/masks. */
#define FEC_ENET_HBERR  ((uint)0x80000000)      /* Heartbeat error */
#define FEC_ENET_BABR   ((uint)0x40000000)      /* Babbling receiver */
#define FEC_ENET_BABT   ((uint)0x20000000)      /* Babbling transmitter */
#define FEC_ENET_GRA    ((uint)0x10000000)      /* Graceful stop complete */
#define FEC_ENET_TXF_0  ((uint)0x08000000)      /* Full frame transmitted */
#define FEC_ENET_TXF_1  ((uint)0x00000008)      /* Full frame transmitted */
#define FEC_ENET_TXF_2  ((uint)0x00000080)      /* Full frame transmitted */
#define FEC_ENET_TXB    ((uint)0x04000000)      /* A buffer was transmitted */
#define FEC_ENET_RXF_0  ((uint)0x02000000)      /* Full frame received */
#define FEC_ENET_RXF_1  ((uint)0x00000002)      /* Full frame received */
#define FEC_ENET_RXF_2  ((uint)0x00000020)      /* Full frame received */
#define FEC_ENET_RXB    ((uint)0x01000000)      /* A buffer was received */
#define FEC_ENET_MII    ((uint)0x00800000)      /* MII interrupt */
#define FEC_ENET_EBERR  ((uint)0x00400000)      /* SDMA bus error */
#define FEC_ENET_WAKEUP ((uint)0x00020000)      /* Wakeup request */
#define FEC_ENET_TXF    (FEC_ENET_TXF_0 | FEC_ENET_TXF_1 | FEC_ENET_TXF_2)
#define FEC_ENET_RXF    (FEC_ENET_RXF_0 | FEC_ENET_RXF_1 | FEC_ENET_RXF_2)
#define FEC_ENET_RXF_GET(X)     (((X) == 0) ? FEC_ENET_RXF_0 :  \
                                (((X) == 1) ? FEC_ENET_RXF_1 :  \
                                FEC_ENET_RXF_2))
#define FEC_ENET_TS_AVAIL       ((uint)0x00010000)
#define FEC_ENET_TS_TIMER       ((uint)0x00008000)

#define FEC_DEFAULT_IMASK (FEC_ENET_TXF | FEC_ENET_RXF)
#define FEC_RX_DISABLED_IMASK (FEC_DEFAULT_IMASK & (~FEC_ENET_RXF))

#define FEC_ENET_TXC_DLY        ((uint)0x00010000)
#define FEC_ENET_RXC_DLY        ((uint)0x00020000)

/* ENET interrupt coalescing macro define */
#define FEC_ITR_CLK_SEL         (0x1 << 30)
#define FEC_ITR_EN              (0x1 << 31)
#define FEC_ITR_ICFT(X)         (((X) & 0xff) << 20)
#define FEC_ITR_ICTT(X)         ((X) & 0xffff)
#define FEC_ITR_ICFT_DEFAULT    200  /* Set 200 frame count threshold */
#define FEC_ITR_ICTT_DEFAULT    1000 /* Set 1000us timer threshold */

#define FEC_VLAN_TAG_LEN        0x04
#define FEC_ETHTYPE_LEN         0x02

/* Controller is ENET-MAC */
#define FEC_QUIRK_ENET_MAC              (1 << 0)
/* Controller needs driver to swap frame */
#define FEC_QUIRK_SWAP_FRAME            (1 << 1)
/* Controller uses gasket */
#define FEC_QUIRK_USE_GASKET            (1 << 2)
/* Controller has GBIT support */
#define FEC_QUIRK_HAS_GBIT              (1 << 3)
/* Controller has extend desc buffer */
#define FEC_QUIRK_HAS_BUFDESC_EX        (1 << 4)
/* Controller has hardware checksum support */
#define FEC_QUIRK_HAS_CSUM              (1 << 5)
/* Controller has hardware vlan support */
#define FEC_QUIRK_HAS_VLAN              (1 << 6)
/* ENET IP errata ERR006358
 *
 * If the ready bit in the transmit buffer descriptor (TxBD[R]) is previously
 * detected as not set during a prior frame transmission, then the
 * ENET_TDAR[TDAR] bit is cleared at a later time, even if additional TxBDs
 * were added to the ring and the ENET_TDAR[TDAR] bit is set. This results in
 * frames not being transmitted until there is a 0-to-1 transition on
 * ENET_TDAR[TDAR].
 */
#define FEC_QUIRK_ERR006358             (1 << 7)
/* ENET IP hw AVB
 *
 * i.MX6SX ENET IP add Audio Video Bridging (AVB) feature support.
 * - Two class indicators on receive with configurable priority
 * - Two class indicators and line speed timer on transmit allowing
 *   implementation class credit based shapers externally
 * - Additional DMA registers provisioned to allow managing up to 3
 *   independent rings
 */
#define FEC_QUIRK_HAS_AVB               (1 << 8)
/* There is a TDAR race condition for mutliQ when the software sets TDAR
 * and the UDMA clears TDAR simultaneously or in a small window (2-4 cycles).
 * This will cause the udma_tx and udma_tx_arbiter state machines to hang.
 * The issue exist at i.MX6SX enet IP.
 */
#define FEC_QUIRK_ERR007885             (1 << 9)
/* ENET Block Guide/ Chapter for the iMX6SX (PELE) address one issue:
 * After set ENET_ATCR[Capture], there need some time cycles before the counter
 * value is capture in the register clock domain.
 * The wait-time-cycles is at least 6 clock cycles of the slower clock between
 * the register clock and the 1588 clock. The 1588 ts_clk is fixed to 25Mhz,
 * register clock is 66Mhz, so the wait-time-cycles must be greater than 240ns
 * (40ns * 6).
 */
#define FEC_QUIRK_BUG_CAPTURE           (1 << 10)
/* Controller has only one MDIO bus */
#define FEC_QUIRK_SINGLE_MDIO           (1 << 11)
/* Controller supports RACC register */
#define FEC_QUIRK_HAS_RACC              (1 << 12)
/* Controller supports interrupt coalesc */
#define FEC_QUIRK_HAS_COALESCE          (1 << 13)
/* Interrupt doesn't wake CPU from deep idle */
#define FEC_QUIRK_ERR006687             (1 << 14)
/* The MIB counters should be cleared and enabled during
 * initialisation.
 */
#define FEC_QUIRK_MIB_CLEAR             (1 << 15)
/* Only i.MX25/i.MX27/i.MX28 controller supports FRBR,FRSR registers,
 * those FIFO receive registers are resolved in other platforms.
 */
#define FEC_QUIRK_HAS_FRREG             (1 << 16)

/* Some FEC hardware blocks need the MMFR cleared at setup time to avoid
 * the generation of an MII event. This must be avoided in the older
 * FEC blocks where it will stop MII events being generated.
 */
#define FEC_QUIRK_CLEAR_SETUP_MII       (1 << 17)

/* Some link partners do not tolerate the momentary reset of the REF_CLK
 * frequency when the RNCTL register is cleared by hardware reset.
 */
#define FEC_QUIRK_NO_HARD_RESET         (1 << 18)

/* i.MX6SX ENET IP supports multiple queues (3 queues), use this quirk to
 * represents this ENET IP.
 */
#define FEC_QUIRK_HAS_MULTI_QUEUES      (1 << 19)

/* i.MX8MQ ENET IP version add new feature to support IEEE 802.3az EEE
 * standard. For the transmission, MAC supply two user registers to set
 * Sleep (TS) and Wake (TW) time.
 */
#define FEC_QUIRK_HAS_EEE               (1 << 20)

/* i.MX8QM ENET IP version add new feture to generate delayed TXC/RXC
 * as an alternative option to make sure it works well with various PHYs.
 * For the implementation of delayed clock, ENET takes synchronized 250MHz
 * clocks to generate 2ns delay.
 */
#define FEC_QUIRK_DELAYED_CLKS_SUPPORT  (1 << 21)

/* i.MX8MQ SoC integration mix wakeup interrupt signal into "int2" interrupt line. */
#define FEC_QUIRK_WAKEUP_FROM_INT2      (1 << 22)

/* i.MX6Q adds pm_qos support */
#define FEC_QUIRK_HAS_PMQOS                     BIT(23)

struct bufdesc_prop {
        int qid;
        /* Address of Rx and Tx buffers */
        struct bufdesc  *base;
        struct bufdesc  *last;
        struct bufdesc  *cur;
        void __iomem    *reg_desc_active;
        dma_addr_t      dma;
        unsigned short ring_size;
        unsigned char dsize;
        unsigned char dsize_log2;
};

struct fec_enet_priv_tx_q {
        struct bufdesc_prop bd;
        unsigned char *tx_bounce[TX_RING_SIZE];
        struct  sk_buff *tx_skbuff[TX_RING_SIZE];

        unsigned short tx_stop_threshold;
        unsigned short tx_wake_threshold;

        struct bufdesc  *dirty_tx;
        char *tso_hdrs;
        dma_addr_t tso_hdrs_dma;
};

struct fec_enet_priv_rx_q {
        struct bufdesc_prop bd;
        struct  sk_buff *rx_skbuff[RX_RING_SIZE];
};

struct fec_stop_mode_gpr {
        struct regmap *gpr;
        u8 reg;
        u8 bit;
};

/* The FEC buffer descriptors track the ring buffers.  The rx_bd_base and
 * tx_bd_base always point to the base of the buffer descriptors.  The
 * cur_rx and cur_tx point to the currently available buffer.
 * The dirty_tx tracks the current buffer that is being sent by the
 * controller.  The cur_tx and dirty_tx are equal under both completely
 * empty and completely full conditions.  The empty/ready indicator in
 * the buffer descriptor determines the actual condition.
 */
struct fec_enet_private {
        /* Hardware registers of the FEC device */
        void __iomem *hwp;

        struct net_device *netdev;

        struct clk *clk_ipg;
        struct clk *clk_ahb;
        struct clk *clk_ref;
        struct clk *clk_enet_out;
        struct clk *clk_ptp;
        struct clk *clk_2x_txclk;

        bool ptp_clk_on;
        struct mutex ptp_clk_mutex;
        unsigned int num_tx_queues;
        unsigned int num_rx_queues;

        /* The saved address of a sent-in-place packet/buffer, for skfree(). */
        struct fec_enet_priv_tx_q *tx_queue[FEC_ENET_MAX_TX_QS];
        struct fec_enet_priv_rx_q *rx_queue[FEC_ENET_MAX_RX_QS];

        unsigned int total_tx_ring_size;
        unsigned int total_rx_ring_size;

        struct  platform_device *pdev;

        int     dev_id;

        /* Phylib and MDIO interface */
        struct  mii_bus *mii_bus;
        uint    phy_speed;
        phy_interface_t phy_interface;
        struct device_node *phy_node;
        bool    rgmii_txc_dly;
        bool    rgmii_rxc_dly;
        int     link;
        int     full_duplex;
        int     speed;
        int     irq[FEC_IRQ_NUM];
        bool    bufdesc_ex;
        int     pause_flag;
        int     wol_flag;
        int     wake_irq;
        u32     quirks;

        struct  napi_struct napi;
        int     csum_flags;

        struct work_struct tx_timeout_work;

        struct ptp_clock *ptp_clock;
        struct ptp_clock_info ptp_caps;
        unsigned long last_overflow_check;
        spinlock_t tmreg_lock;
        struct cyclecounter cc;
        struct timecounter tc;
        int rx_hwtstamp_filter;
        u32 base_incval;
        u32 cycle_speed;
        int hwts_rx_en;
        int hwts_tx_en;
        struct delayed_work time_keep;
        struct regulator *reg_phy;
        struct fec_stop_mode_gpr stop_gpr;
        struct pm_qos_request pm_qos_req;

        unsigned int tx_align;
        unsigned int rx_align;

        /* hw interrupt coalesce */
        unsigned int rx_pkts_itr;
        unsigned int rx_time_itr;
        unsigned int tx_pkts_itr;
        unsigned int tx_time_itr;
        unsigned int itr_clk_rate;

        /* tx lpi eee mode */
        struct ethtool_eee eee;
        unsigned int clk_ref_rate;

        u32 rx_copybreak;

        /* ptp clock period in ns*/
        unsigned int ptp_inc;

        /* pps  */
        int pps_channel;
        unsigned int reload_period;
        int pps_enable;
        unsigned int next_counter;

        u64 ethtool_stats[];
};

void fec_ptp_init(struct platform_device *pdev, int irq_idx);
void fec_ptp_stop(struct platform_device *pdev);
void fec_ptp_start_cyclecounter(struct net_device *ndev);
void fec_ptp_disable_hwts(struct net_device *ndev);
int fec_ptp_set(struct net_device *ndev, struct ifreq *ifr);
int fec_ptp_get(struct net_device *ndev, struct ifreq *ifr);

/****************************************************************************/
#endif /* FEC_H */