drivers/bluetooth/hci_intel.c

   1 // SPDX-License-Identifier: GPL-2.0-or-later
   2 /*
   3  *
   4  *  Bluetooth HCI UART driver for Intel devices
   5  *
   6  *  Copyright (C) 2015  Intel Corporation
   7  */
   8
   9 #include <linux/kernel.h>
  10 #include <linux/errno.h>
  11 #include <linux/skbuff.h>
  12 #include <linux/firmware.h>
  13 #include <linux/module.h>
  14 #include <linux/wait.h>
  15 #include <linux/tty.h>
  16 #include <linux/platform_device.h>
  17 #include <linux/gpio/consumer.h>
  18 #include <linux/acpi.h>
  19 #include <linux/interrupt.h>
  20 #include <linux/pm_runtime.h>
  21
  22 #include <net/bluetooth/bluetooth.h>
  23 #include <net/bluetooth/hci_core.h>
  24
  25 #include "hci_uart.h"
  26 #include "btintel.h"
  27
  28 #define STATE_BOOTLOADER        0
  29 #define STATE_DOWNLOADING       1
  30 #define STATE_FIRMWARE_LOADED   2
  31 #define STATE_FIRMWARE_FAILED   3
  32 #define STATE_BOOTING           4
  33 #define STATE_LPM_ENABLED       5
  34 #define STATE_TX_ACTIVE         6
  35 #define STATE_SUSPENDED         7
  36 #define STATE_LPM_TRANSACTION   8
  37
  38 #define HCI_LPM_WAKE_PKT 0xf0
  39 #define HCI_LPM_PKT 0xf1
  40 #define HCI_LPM_MAX_SIZE 10
  41 #define HCI_LPM_HDR_SIZE HCI_EVENT_HDR_SIZE
  42
  43 #define LPM_OP_TX_NOTIFY 0x00
  44 #define LPM_OP_SUSPEND_ACK 0x02
  45 #define LPM_OP_RESUME_ACK 0x03
  46
  47 #define LPM_SUSPEND_DELAY_MS 1000
  48
  49 struct hci_lpm_pkt {
  50         __u8 opcode;
  51         __u8 dlen;
  52         __u8 data[];
  53 } __packed;
  54
  55 struct intel_device {
  56         struct list_head list;
  57         struct platform_device *pdev;
  58         struct gpio_desc *reset;
  59         struct hci_uart *hu;
  60         struct mutex hu_lock;
  61         int irq;
  62 };
  63
  64 static LIST_HEAD(intel_device_list);
  65 static DEFINE_MUTEX(intel_device_list_lock);
  66
  67 struct intel_data {
  68         struct sk_buff *rx_skb;
  69         struct sk_buff_head txq;
  70         struct work_struct busy_work;
  71         struct hci_uart *hu;
  72         unsigned long flags;
  73 };
  74
  75 static u8 intel_convert_speed(unsigned int speed)
  76 {
  77         switch (speed) {
  78         case 9600:
  79                 return 0x00;
  80         case 19200:
  81                 return 0x01;
  82         case 38400:
  83                 return 0x02;
  84         case 57600:
  85                 return 0x03;
  86         case 115200:
  87                 return 0x04;
  88         case 230400:
  89                 return 0x05;
  90         case 460800:
  91                 return 0x06;
  92         case 921600:
  93                 return 0x07;
  94         case 1843200:
  95                 return 0x08;
  96         case 3250000:
  97                 return 0x09;
  98         case 2000000:
  99                 return 0x0a;
 100         case 3000000:
 101                 return 0x0b;
 102         default:
 103                 return 0xff;
 104         }
 105 }
 106
 107 static int intel_wait_booting(struct hci_uart *hu)
 108 {
 109         struct intel_data *intel = hu->priv;
 110         int err;
 111
 112         err = wait_on_bit_timeout(&intel->flags, STATE_BOOTING,
 113                                   TASK_INTERRUPTIBLE,
 114                                   msecs_to_jiffies(1000));
 115
 116         if (err == -EINTR) {
 117                 bt_dev_err(hu->hdev, "Device boot interrupted");
 118                 return -EINTR;
 119         }
 120
 121         if (err) {
 122                 bt_dev_err(hu->hdev, "Device boot timeout");
 123                 return -ETIMEDOUT;
 124         }
 125
 126         return err;
 127 }
 128
 129 #ifdef CONFIG_PM
 130 static int intel_wait_lpm_transaction(struct hci_uart *hu)
 131 {
 132         struct intel_data *intel = hu->priv;
 133         int err;
 134
 135         err = wait_on_bit_timeout(&intel->flags, STATE_LPM_TRANSACTION,
 136                                   TASK_INTERRUPTIBLE,
 137                                   msecs_to_jiffies(1000));
 138
 139         if (err == -EINTR) {
 140                 bt_dev_err(hu->hdev, "LPM transaction interrupted");
 141                 return -EINTR;
 142         }
 143
 144         if (err) {
 145                 bt_dev_err(hu->hdev, "LPM transaction timeout");
 146                 return -ETIMEDOUT;
 147         }
 148
 149         return err;
 150 }
 151
 152 static int intel_lpm_suspend(struct hci_uart *hu)
 153 {
 154         static const u8 suspend[] = { 0x01, 0x01, 0x01 };
 155         struct intel_data *intel = hu->priv;
 156         struct sk_buff *skb;
 157
 158         if (!test_bit(STATE_LPM_ENABLED, &intel->flags) ||
 159             test_bit(STATE_SUSPENDED, &intel->flags))
 160                 return 0;
 161
 162         if (test_bit(STATE_TX_ACTIVE, &intel->flags))
 163                 return -EAGAIN;
 164
 165         bt_dev_dbg(hu->hdev, "Suspending");
 166
 167         skb = bt_skb_alloc(sizeof(suspend), GFP_KERNEL);
 168         if (!skb) {
 169                 bt_dev_err(hu->hdev, "Failed to alloc memory for LPM packet");
 170                 return -ENOMEM;
 171         }
 172
 173         skb_put_data(skb, suspend, sizeof(suspend));
 174         hci_skb_pkt_type(skb) = HCI_LPM_PKT;
 175
 176         set_bit(STATE_LPM_TRANSACTION, &intel->flags);
 177
 178         /* LPM flow is a priority, enqueue packet at list head */
 179         skb_queue_head(&intel->txq, skb);
 180         hci_uart_tx_wakeup(hu);
 181
 182         intel_wait_lpm_transaction(hu);
 183         /* Even in case of failure, continue and test the suspended flag */
 184
 185         clear_bit(STATE_LPM_TRANSACTION, &intel->flags);
 186
 187         if (!test_bit(STATE_SUSPENDED, &intel->flags)) {
 188                 bt_dev_err(hu->hdev, "Device suspend error");
 189                 return -EINVAL;
 190         }
 191
 192         bt_dev_dbg(hu->hdev, "Suspended");
 193
 194         hci_uart_set_flow_control(hu, true);
 195
 196         return 0;
 197 }
 198
 199 static int intel_lpm_resume(struct hci_uart *hu)
 200 {
 201         struct intel_data *intel = hu->priv;
 202         struct sk_buff *skb;
 203
 204         if (!test_bit(STATE_LPM_ENABLED, &intel->flags) ||
 205             !test_bit(STATE_SUSPENDED, &intel->flags))
 206                 return 0;
 207
 208         bt_dev_dbg(hu->hdev, "Resuming");
 209
 210         hci_uart_set_flow_control(hu, false);
 211
 212         skb = bt_skb_alloc(0, GFP_KERNEL);
 213         if (!skb) {
 214                 bt_dev_err(hu->hdev, "Failed to alloc memory for LPM packet");
 215                 return -ENOMEM;
 216         }
 217
 218         hci_skb_pkt_type(skb) = HCI_LPM_WAKE_PKT;
 219
 220         set_bit(STATE_LPM_TRANSACTION, &intel->flags);
 221
 222         /* LPM flow is a priority, enqueue packet at list head */
 223         skb_queue_head(&intel->txq, skb);
 224         hci_uart_tx_wakeup(hu);
 225
 226         intel_wait_lpm_transaction(hu);
 227         /* Even in case of failure, continue and test the suspended flag */
 228
 229         clear_bit(STATE_LPM_TRANSACTION, &intel->flags);
 230
 231         if (test_bit(STATE_SUSPENDED, &intel->flags)) {
 232                 bt_dev_err(hu->hdev, "Device resume error");
 233                 return -EINVAL;
 234         }
 235
 236         bt_dev_dbg(hu->hdev, "Resumed");
 237
 238         return 0;
 239 }
 240 #endif /* CONFIG_PM */
 241
 242 static int intel_lpm_host_wake(struct hci_uart *hu)
 243 {
 244         static const u8 lpm_resume_ack[] = { LPM_OP_RESUME_ACK, 0x00 };
 245         struct intel_data *intel = hu->priv;
 246         struct sk_buff *skb;
 247
 248         hci_uart_set_flow_control(hu, false);
 249
 250         clear_bit(STATE_SUSPENDED, &intel->flags);
 251
 252         skb = bt_skb_alloc(sizeof(lpm_resume_ack), GFP_KERNEL);
 253         if (!skb) {
 254                 bt_dev_err(hu->hdev, "Failed to alloc memory for LPM packet");
 255                 return -ENOMEM;
 256         }
 257
 258         skb_put_data(skb, lpm_resume_ack, sizeof(lpm_resume_ack));
 259         hci_skb_pkt_type(skb) = HCI_LPM_PKT;
 260
 261         /* LPM flow is a priority, enqueue packet at list head */
 262         skb_queue_head(&intel->txq, skb);
 263         hci_uart_tx_wakeup(hu);
 264
 265         bt_dev_dbg(hu->hdev, "Resumed by controller");
 266
 267         return 0;
 268 }
 269
 270 static irqreturn_t intel_irq(int irq, void *dev_id)
 271 {
 272         struct intel_device *idev = dev_id;
 273
 274         dev_info(&idev->pdev->dev, "hci_intel irq\n");
 275
 276         mutex_lock(&idev->hu_lock);
 277         if (idev->hu)
 278                 intel_lpm_host_wake(idev->hu);
 279         mutex_unlock(&idev->hu_lock);
 280
 281         /* Host/Controller are now LPM resumed, trigger a new delayed suspend */
 282         pm_runtime_get(&idev->pdev->dev);
 283         pm_runtime_mark_last_busy(&idev->pdev->dev);
 284         pm_runtime_put_autosuspend(&idev->pdev->dev);
 285
 286         return IRQ_HANDLED;
 287 }
 288
 289 static int intel_set_power(struct hci_uart *hu, bool powered)
 290 {
 291         struct intel_device *idev;
 292         int err = -ENODEV;
 293
 294         if (!hu->tty->dev)
 295                 return err;
 296
 297         mutex_lock(&intel_device_list_lock);
 298
 299         list_for_each_entry(idev, &intel_device_list, list) {
 300                 /* tty device and pdev device should share the same parent
 301                  * which is the UART port.
 302                  */
 303                 if (hu->tty->dev->parent != idev->pdev->dev.parent)
 304                         continue;
 305
 306                 if (!idev->reset) {
 307                         err = -ENOTSUPP;
 308                         break;
 309                 }
 310
 311                 BT_INFO("hu %p, Switching compatible pm device (%s) to %u",
 312                         hu, dev_name(&idev->pdev->dev), powered);
 313
 314                 gpiod_set_value(idev->reset, powered);
 315
 316                 /* Provide to idev a hu reference which is used to run LPM
 317                  * transactions (lpm suspend/resume) from PM callbacks.
 318                  * hu needs to be protected against concurrent removing during
 319                  * these PM ops.
 320                  */
 321                 mutex_lock(&idev->hu_lock);
 322                 idev->hu = powered ? hu : NULL;
 323                 mutex_unlock(&idev->hu_lock);
 324
 325                 if (idev->irq < 0)
 326                         break;
 327
 328                 if (powered && device_can_wakeup(&idev->pdev->dev)) {
 329                         err = devm_request_threaded_irq(&idev->pdev->dev,
 330                                                         idev->irq, NULL,
 331                                                         intel_irq,
 332                                                         IRQF_ONESHOT,
 333                                                         "bt-host-wake", idev);
 334                         if (err) {
 335                                 BT_ERR("hu %p, unable to allocate irq-%d",
 336                                        hu, idev->irq);
 337                                 break;
 338                         }
 339
 340                         device_wakeup_enable(&idev->pdev->dev);
 341
 342                         pm_runtime_set_active(&idev->pdev->dev);
 343                         pm_runtime_use_autosuspend(&idev->pdev->dev);
 344                         pm_runtime_set_autosuspend_delay(&idev->pdev->dev,
 345                                                          LPM_SUSPEND_DELAY_MS);
 346                         pm_runtime_enable(&idev->pdev->dev);
 347                 } else if (!powered && device_may_wakeup(&idev->pdev->dev)) {
 348                         devm_free_irq(&idev->pdev->dev, idev->irq, idev);
 349                         device_wakeup_disable(&idev->pdev->dev);
 350
 351                         pm_runtime_disable(&idev->pdev->dev);
 352                 }
 353         }
 354
 355         mutex_unlock(&intel_device_list_lock);
 356
 357         return err;
 358 }
 359
 360 static void intel_busy_work(struct work_struct *work)
 361 {
 362         struct intel_data *intel = container_of(work, struct intel_data,
 363                                                 busy_work);
 364         struct intel_device *idev;
 365
 366         if (!intel->hu->tty->dev)
 367                 return;
 368
 369         /* Link is busy, delay the suspend */
 370         mutex_lock(&intel_device_list_lock);
 371         list_for_each_entry(idev, &intel_device_list, list) {
 372                 if (intel->hu->tty->dev->parent == idev->pdev->dev.parent) {
 373                         pm_runtime_get(&idev->pdev->dev);
 374                         pm_runtime_mark_last_busy(&idev->pdev->dev);
 375                         pm_runtime_put_autosuspend(&idev->pdev->dev);
 376                         break;
 377                 }
 378         }
 379         mutex_unlock(&intel_device_list_lock);
 380 }
 381
 382 static int intel_open(struct hci_uart *hu)
 383 {
 384         struct intel_data *intel;
 385
 386         BT_DBG("hu %p", hu);
 387
 388         if (!hci_uart_has_flow_control(hu))
 389                 return -EOPNOTSUPP;
 390
 391         intel = kzalloc(sizeof(*intel), GFP_KERNEL);
 392         if (!intel)
 393                 return -ENOMEM;
 394
 395         skb_queue_head_init(&intel->txq);
 396         INIT_WORK(&intel->busy_work, intel_busy_work);
 397
 398         intel->hu = hu;
 399
 400         hu->priv = intel;
 401
 402         if (!intel_set_power(hu, true))
 403                 set_bit(STATE_BOOTING, &intel->flags);
 404
 405         return 0;
 406 }
 407
 408 static int intel_close(struct hci_uart *hu)
 409 {
 410         struct intel_data *intel = hu->priv;
 411
 412         BT_DBG("hu %p", hu);
 413
 414         cancel_work_sync(&intel->busy_work);
 415
 416         intel_set_power(hu, false);
 417
 418         skb_queue_purge(&intel->txq);
 419         kfree_skb(intel->rx_skb);
 420         kfree(intel);
 421
 422         hu->priv = NULL;
 423         return 0;
 424 }
 425
 426 static int intel_flush(struct hci_uart *hu)
 427 {
 428         struct intel_data *intel = hu->priv;
 429
 430         BT_DBG("hu %p", hu);
 431
 432         skb_queue_purge(&intel->txq);
 433
 434         return 0;
 435 }
 436
 437 static int inject_cmd_complete(struct hci_dev *hdev, __u16 opcode)
 438 {
 439         struct sk_buff *skb;
 440         struct hci_event_hdr *hdr;
 441         struct hci_ev_cmd_complete *evt;
 442
 443         skb = bt_skb_alloc(sizeof(*hdr) + sizeof(*evt) + 1, GFP_KERNEL);
 444         if (!skb)
 445                 return -ENOMEM;
 446
 447         hdr = skb_put(skb, sizeof(*hdr));
 448         hdr->evt = HCI_EV_CMD_COMPLETE;
 449         hdr->plen = sizeof(*evt) + 1;
 450
 451         evt = skb_put(skb, sizeof(*evt));
 452         evt->ncmd = 0x01;
 453         evt->opcode = cpu_to_le16(opcode);
 454
 455         skb_put_u8(skb, 0x00);
 456
 457         hci_skb_pkt_type(skb) = HCI_EVENT_PKT;
 458
 459         return hci_recv_frame(hdev, skb);
 460 }
 461
 462 static int intel_set_baudrate(struct hci_uart *hu, unsigned int speed)
 463 {
 464         struct intel_data *intel = hu->priv;
 465         struct hci_dev *hdev = hu->hdev;
 466         u8 speed_cmd[] = { 0x06, 0xfc, 0x01, 0x00 };
 467         struct sk_buff *skb;
 468         int err;
 469
 470         /* This can be the first command sent to the chip, check
 471          * that the controller is ready.
 472          */
 473         err = intel_wait_booting(hu);
 474
 475         clear_bit(STATE_BOOTING, &intel->flags);
 476
 477         /* In case of timeout, try to continue anyway */
 478         if (err && err != -ETIMEDOUT)
 479                 return err;
 480
 481         bt_dev_info(hdev, "Change controller speed to %d", speed);
 482
 483         speed_cmd[3] = intel_convert_speed(speed);
 484         if (speed_cmd[3] == 0xff) {
 485                 bt_dev_err(hdev, "Unsupported speed");
 486                 return -EINVAL;
 487         }
 488
 489         /* Device will not accept speed change if Intel version has not been
 490          * previously requested.
 491          */
 492         skb = __hci_cmd_sync(hdev, 0xfc05, 0, NULL, HCI_CMD_TIMEOUT);
 493         if (IS_ERR(skb)) {
 494                 bt_dev_err(hdev, "Reading Intel version information failed (%ld)",
 495                            PTR_ERR(skb));
 496                 return PTR_ERR(skb);
 497         }
 498         kfree_skb(skb);
 499
 500         skb = bt_skb_alloc(sizeof(speed_cmd), GFP_KERNEL);
 501         if (!skb) {
 502                 bt_dev_err(hdev, "Failed to alloc memory for baudrate packet");
 503                 return -ENOMEM;
 504         }
 505
 506         skb_put_data(skb, speed_cmd, sizeof(speed_cmd));
 507         hci_skb_pkt_type(skb) = HCI_COMMAND_PKT;
 508
 509         hci_uart_set_flow_control(hu, true);
 510
 511         skb_queue_tail(&intel->txq, skb);
 512         hci_uart_tx_wakeup(hu);
 513
 514         /* wait 100ms to change baudrate on controller side */
 515         msleep(100);
 516
 517         hci_uart_set_baudrate(hu, speed);
 518         hci_uart_set_flow_control(hu, false);
 519
 520         return 0;
 521 }
 522
 523 static int intel_setup(struct hci_uart *hu)
 524 {
 525         struct intel_data *intel = hu->priv;
 526         struct hci_dev *hdev = hu->hdev;
 527         struct sk_buff *skb;
 528         struct intel_version ver;
 529         struct intel_boot_params params;
 530         struct intel_device *idev;
 531         const struct firmware *fw;
 532         char fwname[64];
 533         u32 boot_param;
 534         ktime_t calltime, delta, rettime;
 535         unsigned long long duration;
 536         unsigned int init_speed, oper_speed;
 537         int speed_change = 0;
 538         int err;
 539
 540         bt_dev_dbg(hdev, "");
 541
 542         hu->hdev->set_diag = btintel_set_diag;
 543         hu->hdev->set_bdaddr = btintel_set_bdaddr;
 544
 545         /* Set the default boot parameter to 0x0 and it is updated to
 546          * SKU specific boot parameter after reading Intel_Write_Boot_Params
 547          * command while downloading the firmware.
 548          */
 549         boot_param = 0x00000000;
 550
 551         calltime = ktime_get();
 552
 553         if (hu->init_speed)
 554                 init_speed = hu->init_speed;
 555         else
 556                 init_speed = hu->proto->init_speed;
 557
 558         if (hu->oper_speed)
 559                 oper_speed = hu->oper_speed;
 560         else
 561                 oper_speed = hu->proto->oper_speed;
 562
 563         if (oper_speed && init_speed && oper_speed != init_speed)
 564                 speed_change = 1;
 565
 566         /* Check that the controller is ready */
 567         err = intel_wait_booting(hu);
 568
 569         clear_bit(STATE_BOOTING, &intel->flags);
 570
 571         /* In case of timeout, try to continue anyway */
 572         if (err && err != -ETIMEDOUT)
 573                 return err;
 574
 575         set_bit(STATE_BOOTLOADER, &intel->flags);
 576
 577         /* Read the Intel version information to determine if the device
 578          * is in bootloader mode or if it already has operational firmware
 579          * loaded.
 580          */
 581         err = btintel_read_version(hdev, &ver);
 582         if (err)
 583                 return err;
 584
 585         /* The hardware platform number has a fixed value of 0x37 and
 586          * for now only accept this single value.
 587          */
 588         if (ver.hw_platform != 0x37) {
 589                 bt_dev_err(hdev, "Unsupported Intel hardware platform (%u)",
 590                            ver.hw_platform);
 591                 return -EINVAL;
 592         }
 593
 594         /* Check for supported iBT hardware variants of this firmware
 595          * loading method.
 596          *
 597          * This check has been put in place to ensure correct forward
 598          * compatibility options when newer hardware variants come along.
 599          */
 600         switch (ver.hw_variant) {
 601         case 0x0b:      /* LnP */
 602         case 0x0c:      /* WsP */
 603         case 0x12:      /* ThP */
 604                 break;
 605         default:
 606                 bt_dev_err(hdev, "Unsupported Intel hardware variant (%u)",
 607                            ver.hw_variant);
 608                 return -EINVAL;
 609         }
 610
 611         btintel_version_info(hdev, &ver);
 612
 613         /* The firmware variant determines if the device is in bootloader
 614          * mode or is running operational firmware. The value 0x06 identifies
 615          * the bootloader and the value 0x23 identifies the operational
 616          * firmware.
 617          *
 618          * When the operational firmware is already present, then only
 619          * the check for valid Bluetooth device address is needed. This
 620          * determines if the device will be added as configured or
 621          * unconfigured controller.
 622          *
 623          * It is not possible to use the Secure Boot Parameters in this
 624          * case since that command is only available in bootloader mode.
 625          */
 626         if (ver.fw_variant == 0x23) {
 627                 clear_bit(STATE_BOOTLOADER, &intel->flags);
 628                 btintel_check_bdaddr(hdev);
 629                 return 0;
 630         }
 631
 632         /* If the device is not in bootloader mode, then the only possible
 633          * choice is to return an error and abort the device initialization.
 634          */
 635         if (ver.fw_variant != 0x06) {
 636                 bt_dev_err(hdev, "Unsupported Intel firmware variant (%u)",
 637                            ver.fw_variant);
 638                 return -ENODEV;
 639         }
 640
 641         /* Read the secure boot parameters to identify the operating
 642          * details of the bootloader.
 643          */
 644         err = btintel_read_boot_params(hdev, &params);
 645         if (err)
 646                 return err;
 647
 648         /* It is required that every single firmware fragment is acknowledged
 649          * with a command complete event. If the boot parameters indicate
 650          * that this bootloader does not send them, then abort the setup.
 651          */
 652         if (params.limited_cce != 0x00) {
 653                 bt_dev_err(hdev, "Unsupported Intel firmware loading method (%u)",
 654                            params.limited_cce);
 655                 return -EINVAL;
 656         }
 657
 658         /* If the OTP has no valid Bluetooth device address, then there will
 659          * also be no valid address for the operational firmware.
 660          */
 661         if (!bacmp(&params.otp_bdaddr, BDADDR_ANY)) {
 662                 bt_dev_info(hdev, "No device address configured");
 663                 set_bit(HCI_QUIRK_INVALID_BDADDR, &hdev->quirks);
 664         }
 665
 666         /* With this Intel bootloader only the hardware variant and device
 667          * revision information are used to select the right firmware for SfP
 668          * and WsP.
 669          *
 670          * The firmware filename is ibt-<hw_variant>-<dev_revid>.sfi.
 671          *
 672          * Currently the supported hardware variants are:
 673          *   11 (0x0b) for iBT 3.0 (LnP/SfP)
 674          *   12 (0x0c) for iBT 3.5 (WsP)
 675          *
 676          * For ThP/JfP and for future SKU's, the FW name varies based on HW
 677          * variant, HW revision and FW revision, as these are dependent on CNVi
 678          * and RF Combination.
 679          *
 680          *   18 (0x12) for iBT3.5 (ThP/JfP)
 681          *
 682          * The firmware file name for these will be
 683          * ibt-<hw_variant>-<hw_revision>-<fw_revision>.sfi.
 684          *
 685          */
 686         switch (ver.hw_variant) {
 687         case 0x0b:      /* SfP */
 688         case 0x0c:      /* WsP */
 689                 snprintf(fwname, sizeof(fwname), "intel/ibt-%u-%u.sfi",
 690                          ver.hw_variant, le16_to_cpu(params.dev_revid));
 691                 break;
 692         case 0x12:      /* ThP */
 693                 snprintf(fwname, sizeof(fwname), "intel/ibt-%u-%u-%u.sfi",
 694                          ver.hw_variant, ver.hw_revision, ver.fw_revision);
 695                 break;
 696         default:
 697                 bt_dev_err(hdev, "Unsupported Intel hardware variant (%u)",
 698                            ver.hw_variant);
 699                 return -EINVAL;
 700         }
 701
 702         err = request_firmware(&fw, fwname, &hdev->dev);
 703         if (err < 0) {
 704                 bt_dev_err(hdev, "Failed to load Intel firmware file (%d)",
 705                            err);
 706                 return err;
 707         }
 708
 709         bt_dev_info(hdev, "Found device firmware: %s", fwname);
 710
 711         /* Save the DDC file name for later */
 712         switch (ver.hw_variant) {
 713         case 0x0b:      /* SfP */
 714         case 0x0c:      /* WsP */
 715                 snprintf(fwname, sizeof(fwname), "intel/ibt-%u-%u.ddc",
 716                          ver.hw_variant, le16_to_cpu(params.dev_revid));
 717                 break;
 718         case 0x12:      /* ThP */
 719                 snprintf(fwname, sizeof(fwname), "intel/ibt-%u-%u-%u.ddc",
 720                          ver.hw_variant, ver.hw_revision, ver.fw_revision);
 721                 break;
 722         default:
 723                 bt_dev_err(hdev, "Unsupported Intel hardware variant (%u)",
 724                            ver.hw_variant);
 725                 return -EINVAL;
 726         }
 727
 728         if (fw->size < 644) {
 729                 bt_dev_err(hdev, "Invalid size of firmware file (%zu)",
 730                            fw->size);
 731                 err = -EBADF;
 732                 goto done;
 733         }
 734
 735         set_bit(STATE_DOWNLOADING, &intel->flags);
 736
 737         /* Start firmware downloading and get boot parameter */
 738         err = btintel_download_firmware(hdev, &ver, fw, &boot_param);
 739         if (err < 0)
 740                 goto done;
 741
 742         set_bit(STATE_FIRMWARE_LOADED, &intel->flags);
 743
 744         bt_dev_info(hdev, "Waiting for firmware download to complete");
 745
 746         /* Before switching the device into operational mode and with that
 747          * booting the loaded firmware, wait for the bootloader notification
 748          * that all fragments have been successfully received.
 749          *
 750          * When the event processing receives the notification, then the
 751          * STATE_DOWNLOADING flag will be cleared.
 752          *
 753          * The firmware loading should not take longer than 5 seconds
 754          * and thus just timeout if that happens and fail the setup
 755          * of this device.
 756          */
 757         err = wait_on_bit_timeout(&intel->flags, STATE_DOWNLOADING,
 758                                   TASK_INTERRUPTIBLE,
 759                                   msecs_to_jiffies(5000));
 760         if (err == -EINTR) {
 761                 bt_dev_err(hdev, "Firmware loading interrupted");
 762                 err = -EINTR;
 763                 goto done;
 764         }
 765
 766         if (err) {
 767                 bt_dev_err(hdev, "Firmware loading timeout");
 768                 err = -ETIMEDOUT;
 769                 goto done;
 770         }
 771
 772         if (test_bit(STATE_FIRMWARE_FAILED, &intel->flags)) {
 773                 bt_dev_err(hdev, "Firmware loading failed");
 774                 err = -ENOEXEC;
 775                 goto done;
 776         }
 777
 778         rettime = ktime_get();
 779         delta = ktime_sub(rettime, calltime);
 780         duration = (unsigned long long)ktime_to_ns(delta) >> 10;
 781
 782         bt_dev_info(hdev, "Firmware loaded in %llu usecs", duration);
 783
 784 done:
 785         release_firmware(fw);
 786
 787         /* Check if there was an error and if is not -EALREADY which means the
 788          * firmware has already been loaded.
 789          */
 790         if (err < 0 && err != -EALREADY)
 791                 return err;
 792
 793         /* We need to restore the default speed before Intel reset */
 794         if (speed_change) {
 795                 err = intel_set_baudrate(hu, init_speed);
 796                 if (err)
 797                         return err;
 798         }
 799
 800         calltime = ktime_get();
 801
 802         set_bit(STATE_BOOTING, &intel->flags);
 803
 804         err = btintel_send_intel_reset(hdev, boot_param);
 805         if (err)
 806                 return err;
 807
 808         /* The bootloader will not indicate when the device is ready. This
 809          * is done by the operational firmware sending bootup notification.
 810          *
 811          * Booting into operational firmware should not take longer than
 812          * 1 second. However if that happens, then just fail the setup
 813          * since something went wrong.
 814          */
 815         bt_dev_info(hdev, "Waiting for device to boot");
 816
 817         err = intel_wait_booting(hu);
 818         if (err)
 819                 return err;
 820
 821         clear_bit(STATE_BOOTING, &intel->flags);
 822
 823         rettime = ktime_get();
 824         delta = ktime_sub(rettime, calltime);
 825         duration = (unsigned long long)ktime_to_ns(delta) >> 10;
 826
 827         bt_dev_info(hdev, "Device booted in %llu usecs", duration);
 828
 829         /* Enable LPM if matching pdev with wakeup enabled, set TX active
 830          * until further LPM TX notification.
 831          */
 832         mutex_lock(&intel_device_list_lock);
 833         list_for_each_entry(idev, &intel_device_list, list) {
 834                 if (!hu->tty->dev)
 835                         break;
 836                 if (hu->tty->dev->parent == idev->pdev->dev.parent) {
 837                         if (device_may_wakeup(&idev->pdev->dev)) {
 838                                 set_bit(STATE_LPM_ENABLED, &intel->flags);
 839                                 set_bit(STATE_TX_ACTIVE, &intel->flags);
 840                         }
 841                         break;
 842                 }
 843         }
 844         mutex_unlock(&intel_device_list_lock);
 845
 846         /* Ignore errors, device can work without DDC parameters */
 847         btintel_load_ddc_config(hdev, fwname);
 848
 849         skb = __hci_cmd_sync(hdev, HCI_OP_RESET, 0, NULL, HCI_CMD_TIMEOUT);
 850         if (IS_ERR(skb))
 851                 return PTR_ERR(skb);
 852         kfree_skb(skb);
 853
 854         if (speed_change) {
 855                 err = intel_set_baudrate(hu, oper_speed);
 856                 if (err)
 857                         return err;
 858         }
 859
 860         bt_dev_info(hdev, "Setup complete");
 861
 862         clear_bit(STATE_BOOTLOADER, &intel->flags);
 863
 864         return 0;
 865 }
 866
 867 static int intel_recv_event(struct hci_dev *hdev, struct sk_buff *skb)
 868 {
 869         struct hci_uart *hu = hci_get_drvdata(hdev);
 870         struct intel_data *intel = hu->priv;
 871         struct hci_event_hdr *hdr;
 872
 873         if (!test_bit(STATE_BOOTLOADER, &intel->flags) &&
 874             !test_bit(STATE_BOOTING, &intel->flags))
 875                 goto recv;
 876
 877         hdr = (void *)skb->data;
 878
 879         /* When the firmware loading completes the device sends
 880          * out a vendor specific event indicating the result of
 881          * the firmware loading.
 882          */
 883         if (skb->len == 7 && hdr->evt == 0xff && hdr->plen == 0x05 &&
 884             skb->data[2] == 0x06) {
 885                 if (skb->data[3] != 0x00)
 886                         set_bit(STATE_FIRMWARE_FAILED, &intel->flags);
 887
 888                 if (test_and_clear_bit(STATE_DOWNLOADING, &intel->flags) &&
 889                     test_bit(STATE_FIRMWARE_LOADED, &intel->flags))
 890                         wake_up_bit(&intel->flags, STATE_DOWNLOADING);
 891
 892         /* When switching to the operational firmware the device
 893          * sends a vendor specific event indicating that the bootup
 894          * completed.
 895          */
 896         } else if (skb->len == 9 && hdr->evt == 0xff && hdr->plen == 0x07 &&
 897                    skb->data[2] == 0x02) {
 898                 if (test_and_clear_bit(STATE_BOOTING, &intel->flags))
 899                         wake_up_bit(&intel->flags, STATE_BOOTING);
 900         }
 901 recv:
 902         return hci_recv_frame(hdev, skb);
 903 }
 904
 905 static void intel_recv_lpm_notify(struct hci_dev *hdev, int value)
 906 {
 907         struct hci_uart *hu = hci_get_drvdata(hdev);
 908         struct intel_data *intel = hu->priv;
 909
 910         bt_dev_dbg(hdev, "TX idle notification (%d)", value);
 911
 912         if (value) {
 913                 set_bit(STATE_TX_ACTIVE, &intel->flags);
 914                 schedule_work(&intel->busy_work);
 915         } else {
 916                 clear_bit(STATE_TX_ACTIVE, &intel->flags);
 917         }
 918 }
 919
 920 static int intel_recv_lpm(struct hci_dev *hdev, struct sk_buff *skb)
 921 {
 922         struct hci_lpm_pkt *lpm = (void *)skb->data;
 923         struct hci_uart *hu = hci_get_drvdata(hdev);
 924         struct intel_data *intel = hu->priv;
 925
 926         switch (lpm->opcode) {
 927         case LPM_OP_TX_NOTIFY:
 928                 if (lpm->dlen < 1) {
 929                         bt_dev_err(hu->hdev, "Invalid LPM notification packet");
 930                         break;
 931                 }
 932                 intel_recv_lpm_notify(hdev, lpm->data[0]);
 933                 break;
 934         case LPM_OP_SUSPEND_ACK:
 935                 set_bit(STATE_SUSPENDED, &intel->flags);
 936                 if (test_and_clear_bit(STATE_LPM_TRANSACTION, &intel->flags))
 937                         wake_up_bit(&intel->flags, STATE_LPM_TRANSACTION);
 938                 break;
 939         case LPM_OP_RESUME_ACK:
 940                 clear_bit(STATE_SUSPENDED, &intel->flags);
 941                 if (test_and_clear_bit(STATE_LPM_TRANSACTION, &intel->flags))
 942                         wake_up_bit(&intel->flags, STATE_LPM_TRANSACTION);
 943                 break;
 944         default:
 945                 bt_dev_err(hdev, "Unknown LPM opcode (%02x)", lpm->opcode);
 946                 break;
 947         }
 948
 949         kfree_skb(skb);
 950
 951         return 0;
 952 }
 953
 954 #define INTEL_RECV_LPM \
 955         .type = HCI_LPM_PKT, \
 956         .hlen = HCI_LPM_HDR_SIZE, \
 957         .loff = 1, \
 958         .lsize = 1, \
 959         .maxlen = HCI_LPM_MAX_SIZE
 960
 961 static const struct h4_recv_pkt intel_recv_pkts[] = {
 962         { H4_RECV_ACL,    .recv = hci_recv_frame   },
 963         { H4_RECV_SCO,    .recv = hci_recv_frame   },
 964         { H4_RECV_EVENT,  .recv = intel_recv_event },
 965         { INTEL_RECV_LPM, .recv = intel_recv_lpm   },
 966 };
 967
 968 static int intel_recv(struct hci_uart *hu, const void *data, int count)
 969 {
 970         struct intel_data *intel = hu->priv;
 971
 972         if (!test_bit(HCI_UART_REGISTERED, &hu->flags))
 973                 return -EUNATCH;
 974
 975         intel->rx_skb = h4_recv_buf(hu->hdev, intel->rx_skb, data, count,
 976                                     intel_recv_pkts,
 977                                     ARRAY_SIZE(intel_recv_pkts));
 978         if (IS_ERR(intel->rx_skb)) {
 979                 int err = PTR_ERR(intel->rx_skb);
 980
 981                 bt_dev_err(hu->hdev, "Frame reassembly failed (%d)", err);
 982                 intel->rx_skb = NULL;
 983                 return err;
 984         }
 985
 986         return count;
 987 }
 988
 989 static int intel_enqueue(struct hci_uart *hu, struct sk_buff *skb)
 990 {
 991         struct intel_data *intel = hu->priv;
 992         struct intel_device *idev;
 993
 994         BT_DBG("hu %p skb %p", hu, skb);
 995
 996         if (!hu->tty->dev)
 997                 goto out_enqueue;
 998
 999         /* Be sure our controller is resumed and potential LPM transaction
1000          * completed before enqueuing any packet.
1001          */
1002         mutex_lock(&intel_device_list_lock);
1003         list_for_each_entry(idev, &intel_device_list, list) {
1004                 if (hu->tty->dev->parent == idev->pdev->dev.parent) {
1005                         pm_runtime_get_sync(&idev->pdev->dev);
1006                         pm_runtime_mark_last_busy(&idev->pdev->dev);
1007                         pm_runtime_put_autosuspend(&idev->pdev->dev);
1008                         break;
1009                 }
1010         }
1011         mutex_unlock(&intel_device_list_lock);
1012 out_enqueue:
1013         skb_queue_tail(&intel->txq, skb);
1014
1015         return 0;
1016 }
1017
1018 static struct sk_buff *intel_dequeue(struct hci_uart *hu)
1019 {
1020         struct intel_data *intel = hu->priv;
1021         struct sk_buff *skb;
1022
1023         skb = skb_dequeue(&intel->txq);
1024         if (!skb)
1025                 return skb;
1026
1027         if (test_bit(STATE_BOOTLOADER, &intel->flags) &&
1028             (hci_skb_pkt_type(skb) == HCI_COMMAND_PKT)) {
1029                 struct hci_command_hdr *cmd = (void *)skb->data;
1030                 __u16 opcode = le16_to_cpu(cmd->opcode);
1031
1032                 /* When the 0xfc01 command is issued to boot into
1033                  * the operational firmware, it will actually not
1034                  * send a command complete event. To keep the flow
1035                  * control working inject that event here.
1036                  */
1037                 if (opcode == 0xfc01)
1038                         inject_cmd_complete(hu->hdev, opcode);
1039         }
1040
1041         /* Prepend skb with frame type */
1042         memcpy(skb_push(skb, 1), &hci_skb_pkt_type(skb), 1);
1043
1044         return skb;
1045 }
1046
1047 static const struct hci_uart_proto intel_proto = {
1048         .id             = HCI_UART_INTEL,
1049         .name           = "Intel",
1050         .manufacturer   = 2,
1051         .init_speed     = 115200,
1052         .oper_speed     = 3000000,
1053         .open           = intel_open,
1054         .close          = intel_close,
1055         .flush          = intel_flush,
1056         .setup          = intel_setup,
1057         .set_baudrate   = intel_set_baudrate,
1058         .recv           = intel_recv,
1059         .enqueue        = intel_enqueue,
1060         .dequeue        = intel_dequeue,
1061 };
1062
1063 #ifdef CONFIG_ACPI
1064 static const struct acpi_device_id intel_acpi_match[] = {
1065         { "INT33E1", 0 },
1066         { "INT33E3", 0 },
1067         { }
1068 };
1069 MODULE_DEVICE_TABLE(acpi, intel_acpi_match);
1070 #endif
1071
1072 #ifdef CONFIG_PM
1073 static int intel_suspend_device(struct device *dev)
1074 {
1075         struct intel_device *idev = dev_get_drvdata(dev);
1076
1077         mutex_lock(&idev->hu_lock);
1078         if (idev->hu)
1079                 intel_lpm_suspend(idev->hu);
1080         mutex_unlock(&idev->hu_lock);
1081
1082         return 0;
1083 }
1084
1085 static int intel_resume_device(struct device *dev)
1086 {
1087         struct intel_device *idev = dev_get_drvdata(dev);
1088
1089         mutex_lock(&idev->hu_lock);
1090         if (idev->hu)
1091                 intel_lpm_resume(idev->hu);
1092         mutex_unlock(&idev->hu_lock);
1093
1094         return 0;
1095 }
1096 #endif
1097
1098 #ifdef CONFIG_PM_SLEEP
1099 static int intel_suspend(struct device *dev)
1100 {
1101         struct intel_device *idev = dev_get_drvdata(dev);
1102
1103         if (device_may_wakeup(dev))
1104                 enable_irq_wake(idev->irq);
1105
1106         return intel_suspend_device(dev);
1107 }
1108
1109 static int intel_resume(struct device *dev)
1110 {
1111         struct intel_device *idev = dev_get_drvdata(dev);
1112
1113         if (device_may_wakeup(dev))
1114                 disable_irq_wake(idev->irq);
1115
1116         return intel_resume_device(dev);
1117 }
1118 #endif
1119
1120 static const struct dev_pm_ops intel_pm_ops = {
1121         SET_SYSTEM_SLEEP_PM_OPS(intel_suspend, intel_resume)
1122         SET_RUNTIME_PM_OPS(intel_suspend_device, intel_resume_device, NULL)
1123 };
1124
1125 static const struct acpi_gpio_params reset_gpios = { 0, 0, false };
1126 static const struct acpi_gpio_params host_wake_gpios = { 1, 0, false };
1127
1128 static const struct acpi_gpio_mapping acpi_hci_intel_gpios[] = {
1129         { "reset-gpios", &reset_gpios, 1, ACPI_GPIO_QUIRK_ONLY_GPIOIO },
1130         { "host-wake-gpios", &host_wake_gpios, 1, ACPI_GPIO_QUIRK_ONLY_GPIOIO },
1131         { }
1132 };
1133
1134 static int intel_probe(struct platform_device *pdev)
1135 {
1136         struct intel_device *idev;
1137         int ret;
1138
1139         idev = devm_kzalloc(&pdev->dev, sizeof(*idev), GFP_KERNEL);
1140         if (!idev)
1141                 return -ENOMEM;
1142
1143         mutex_init(&idev->hu_lock);
1144
1145         idev->pdev = pdev;
1146
1147         ret = devm_acpi_dev_add_driver_gpios(&pdev->dev, acpi_hci_intel_gpios);
1148         if (ret)
1149                 dev_dbg(&pdev->dev, "Unable to add GPIO mapping table\n");
1150
1151         idev->reset = devm_gpiod_get(&pdev->dev, "reset", GPIOD_OUT_LOW);
1152         if (IS_ERR(idev->reset)) {
1153                 dev_err(&pdev->dev, "Unable to retrieve gpio\n");
1154                 return PTR_ERR(idev->reset);
1155         }
1156
1157         idev->irq = platform_get_irq(pdev, 0);
1158         if (idev->irq < 0) {
1159                 struct gpio_desc *host_wake;
1160
1161                 dev_err(&pdev->dev, "No IRQ, falling back to gpio-irq\n");
1162
1163                 host_wake = devm_gpiod_get(&pdev->dev, "host-wake", GPIOD_IN);
1164                 if (IS_ERR(host_wake)) {
1165                         dev_err(&pdev->dev, "Unable to retrieve IRQ\n");
1166                         goto no_irq;
1167                 }
1168
1169                 idev->irq = gpiod_to_irq(host_wake);
1170                 if (idev->irq < 0) {
1171                         dev_err(&pdev->dev, "No corresponding irq for gpio\n");
1172                         goto no_irq;
1173                 }
1174         }
1175
1176         /* Only enable wake-up/irq when controller is powered */
1177         device_set_wakeup_capable(&pdev->dev, true);
1178         device_wakeup_disable(&pdev->dev);
1179
1180 no_irq:
1181         platform_set_drvdata(pdev, idev);
1182
1183         /* Place this instance on the device list */
1184         mutex_lock(&intel_device_list_lock);
1185         list_add_tail(&idev->list, &intel_device_list);
1186         mutex_unlock(&intel_device_list_lock);
1187
1188         dev_info(&pdev->dev, "registered, gpio(%d)/irq(%d).\n",
1189                  desc_to_gpio(idev->reset), idev->irq);
1190
1191         return 0;
1192 }
1193
1194 static void intel_remove(struct platform_device *pdev)
1195 {
1196         struct intel_device *idev = platform_get_drvdata(pdev);
1197
1198         device_wakeup_disable(&pdev->dev);
1199
1200         mutex_lock(&intel_device_list_lock);
1201         list_del(&idev->list);
1202         mutex_unlock(&intel_device_list_lock);
1203
1204         dev_info(&pdev->dev, "unregistered.\n");
1205 }
1206
1207 static struct platform_driver intel_driver = {
1208         .probe = intel_probe,
1209         .remove_new = intel_remove,
1210         .driver = {
1211                 .name = "hci_intel",
1212                 .acpi_match_table = ACPI_PTR(intel_acpi_match),
1213                 .pm = &intel_pm_ops,
1214         },
1215 };
1216
1217 int __init intel_init(void)
1218 {
1219         int err;
1220
1221         err = platform_driver_register(&intel_driver);
1222         if (err)
1223                 return err;
1224
1225         return hci_uart_register_proto(&intel_proto);
1226 }
1227
1228 int __exit intel_deinit(void)
1229 {
1230         platform_driver_unregister(&intel_driver);
1231
1232         return hci_uart_unregister_proto(&intel_proto);
1233 }