arch/arm64/boot/dts/qcom/msm8916-longcheer-l8150.dts

   1 // SPDX-License-Identifier: GPL-2.0-only
   2
   3 /dts-v1/;
   4
   5 #include "msm8916-pm8916.dtsi"
   6 #include <dt-bindings/gpio/gpio.h>
   7 #include <dt-bindings/input/input.h>
   8 #include <dt-bindings/interrupt-controller/irq.h>
   9 #include <dt-bindings/leds/common.h>
  10
  11 / {
  12         model = "Longcheer L8150";
  13         compatible = "longcheer,l8150", "qcom,msm8916-v1-qrd/9-v1", "qcom,msm8916";
  14         chassis-type = "handset";
  15
  16         aliases {
  17                 serial0 = &blsp1_uart2;
  18         };
  19
  20         chosen {
  21                 stdout-path = "serial0";
  22         };
  23
  24         reserved-memory {
  25                 // wcnss.mdt is not relocatable, so it must be loaded at 0x8b600000
  26                 /delete-node/ wcnss@89300000;
  27
  28                 wcnss_mem: wcnss@8b600000 {
  29                         reg = <0x0 0x8b600000 0x0 0x600000>;
  30                         no-map;
  31                 };
  32         };
  33
  34         gpio-keys {
  35                 compatible = "gpio-keys";
  36
  37                 pinctrl-names = "default";
  38                 pinctrl-0 = <&gpio_keys_default>;
  39
  40                 label = "GPIO Buttons";
  41
  42                 volume-up {
  43                         label = "Volume Up";
  44                         gpios = <&msmgpio 107 GPIO_ACTIVE_LOW>;
  45                         linux,code = <KEY_VOLUMEUP>;
  46                 };
  47         };
  48
  49         reg_ctp: regulator-ctp {
  50                 compatible = "regulator-fixed";
  51                 regulator-name = "ctp";
  52
  53                 regulator-min-microvolt = <2800000>;
  54                 regulator-max-microvolt = <2800000>;
  55
  56                 gpio = <&msmgpio 17 GPIO_ACTIVE_HIGH>;
  57                 enable-active-high;
  58
  59                 pinctrl-names = "default";
  60                 pinctrl-0 = <&ctp_pwr_en_default>;
  61         };
  62
  63         flash-led-controller {
  64                 compatible = "sgmicro,sgm3140";
  65                 flash-gpios = <&msmgpio 31 GPIO_ACTIVE_HIGH>;
  66                 enable-gpios = <&msmgpio 32 GPIO_ACTIVE_HIGH>;
  67
  68                 pinctrl-names = "default";
  69                 pinctrl-0 = <&camera_flash_default>;
  70
  71                 flash_led: led {
  72                         function = LED_FUNCTION_FLASH;
  73                         color = <LED_COLOR_ID_WHITE>;
  74                         flash-max-timeout-us = <250000>;
  75                 };
  76         };
  77 };
  78
  79 &blsp_i2c1 {
  80         status = "okay";
  81
  82         led-controller@45 {
  83                 compatible = "awinic,aw2013";
  84                 reg = <0x45>;
  85                 #address-cells = <1>;
  86                 #size-cells = <0>;
  87
  88                 vcc-supply = <&pm8916_l17>;
  89
  90                 led@0 {
  91                         reg = <0>;
  92                         led-max-microamp = <5000>;
  93                         function = LED_FUNCTION_INDICATOR;
  94                         color = <LED_COLOR_ID_RED>;
  95                 };
  96
  97                 led@1 {
  98                         reg = <1>;
  99                         led-max-microamp = <5000>;
 100                         function = LED_FUNCTION_INDICATOR;
 101                         color = <LED_COLOR_ID_GREEN>;
 102                 };
 103
 104                 led@2 {
 105                         reg = <2>;
 106                         led-max-microamp = <5000>;
 107                         function = LED_FUNCTION_INDICATOR;
 108                         color = <LED_COLOR_ID_BLUE>;
 109                 };
 110         };
 111 };
 112
 113 &blsp_i2c2 {
 114         status = "okay";
 115
 116         accelerometer@10 {
 117                 compatible = "bosch,bmc156_accel";
 118                 reg = <0x10>;
 119
 120                 /*
 121                  * For some reason the interrupt line is usually not connected
 122                  * to the BMC156. However, there are two pads next to the chip
 123                  * that can be shorted to make it work if needed.
 124                  *
 125                  * interrupt-parent = <&msmgpio>;
 126                  * interrupts = <116 IRQ_TYPE_EDGE_RISING>;
 127                  */
 128
 129                 pinctrl-names = "default";
 130                 pinctrl-0 = <&accel_int_default>;
 131
 132                 vdd-supply = <&pm8916_l17>;
 133                 vddio-supply = <&pm8916_l6>;
 134
 135                 mount-matrix = "0", "1", "0",
 136                               "-1", "0", "0",
 137                                "0", "0", "1";
 138         };
 139
 140         magnetometer@12 {
 141                 compatible = "bosch,bmc156_magn";
 142                 reg = <0x12>;
 143
 144                 interrupt-parent = <&msmgpio>;
 145                 interrupts = <113 IRQ_TYPE_EDGE_RISING>;
 146
 147                 pinctrl-names = "default";
 148                 pinctrl-0 = <&magn_int_default>;
 149
 150                 vdd-supply = <&pm8916_l17>;
 151                 vddio-supply = <&pm8916_l6>;
 152         };
 153
 154         light-sensor@23 {
 155                 compatible = "liteon,ltr559";
 156                 reg = <0x23>;
 157                 proximity-near-level = <75>;
 158
 159                 interrupt-parent = <&msmgpio>;
 160                 interrupts = <115 IRQ_TYPE_EDGE_FALLING>;
 161
 162                 pinctrl-names = "default";
 163                 pinctrl-0 = <&light_int_default>;
 164
 165                 vdd-supply = <&pm8916_l17>;
 166                 vio-supply = <&pm8916_l6>;
 167         };
 168
 169         gyroscope@68 {
 170                 compatible = "bosch,bmg160";
 171                 reg = <0x68>;
 172
 173                 interrupt-parent = <&msmgpio>;
 174                 interrupts = <23 IRQ_TYPE_EDGE_RISING>,
 175                              <22 IRQ_TYPE_EDGE_RISING>;
 176
 177                 pinctrl-names = "default";
 178                 pinctrl-0 = <&gyro_int_default>;
 179
 180                 vdd-supply = <&pm8916_l17>;
 181                 vddio-supply = <&pm8916_l6>;
 182         };
 183 };
 184
 185 &blsp_i2c5 {
 186         status = "okay";
 187
 188         rmi4@20 {
 189                 compatible = "syna,rmi4-i2c";
 190                 reg = <0x20>;
 191                 #address-cells = <1>;
 192                 #size-cells = <0>;
 193
 194                 interrupt-parent = <&msmgpio>;
 195                 interrupts = <13 IRQ_TYPE_EDGE_FALLING>;
 196
 197                 vdd-supply = <&reg_ctp>;
 198                 vio-supply = <&pm8916_l6>;
 199
 200                 pinctrl-names = "default";
 201                 pinctrl-0 = <&tp_int_default>;
 202
 203                 syna,startup-delay-ms = <10>;
 204
 205                 rmi4-f01@1 {
 206                         reg = <0x1>;
 207                         syna,nosleep-mode = <1>; // Allow sleeping
 208                 };
 209
 210                 rmi4-f12@12 {
 211                         reg = <0x12>;
 212                         syna,sensor-type = <1>; // Touchscreen
 213                 };
 214         };
 215 };
 216
 217 &blsp1_uart2 {
 218         status = "okay";
 219 };
 220
 221 &pm8916_resin {
 222         status = "okay";
 223         linux,code = <KEY_VOLUMEDOWN>;
 224 };
 225
 226 &pm8916_usbin {
 227         status = "okay";
 228 };
 229
 230 &pm8916_vib {
 231         status = "okay";
 232 };
 233
 234 &pronto {
 235         status = "okay";
 236 };
 237
 238 &sdhc_1 {
 239         status = "okay";
 240
 241         pinctrl-names = "default", "sleep";
 242         pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on>;
 243         pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off>;
 244 };
 245
 246 &sdhc_2 {
 247         status = "okay";
 248
 249         pinctrl-names = "default", "sleep";
 250         pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on>;
 251         pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off>;
 252
 253         non-removable;
 254 };
 255
 256 &usb {
 257         status = "okay";
 258         dr_mode = "peripheral";
 259         extcon = <&pm8916_usbin>;
 260 };
 261
 262 &usb_hs_phy {
 263         extcon = <&pm8916_usbin>;
 264 };
 265
 266 &smd_rpm_regulators {
 267         vdd_l1_l2_l3-supply = <&pm8916_s3>;
 268         vdd_l4_l5_l6-supply = <&pm8916_s4>;
 269         vdd_l7-supply = <&pm8916_s4>;
 270
 271         s3 {
 272                 regulator-min-microvolt = <1200000>;
 273                 regulator-max-microvolt = <1300000>;
 274         };
 275
 276         s4 {
 277                 regulator-min-microvolt = <1800000>;
 278                 regulator-max-microvolt = <2100000>;
 279         };
 280
 281         l1 {
 282                 regulator-min-microvolt = <1225000>;
 283                 regulator-max-microvolt = <1225000>;
 284         };
 285
 286         l2 {
 287                 regulator-min-microvolt = <1200000>;
 288                 regulator-max-microvolt = <1200000>;
 289         };
 290
 291         l4 {
 292                 regulator-min-microvolt = <2050000>;
 293                 regulator-max-microvolt = <2050000>;
 294         };
 295
 296         l5 {
 297                 regulator-min-microvolt = <1800000>;
 298                 regulator-max-microvolt = <1800000>;
 299         };
 300
 301         l6 {
 302                 regulator-min-microvolt = <1800000>;
 303                 regulator-max-microvolt = <1800000>;
 304         };
 305
 306         l7 {
 307                 regulator-min-microvolt = <1800000>;
 308                 regulator-max-microvolt = <1800000>;
 309         };
 310
 311         l8 {
 312                 regulator-min-microvolt = <2850000>;
 313                 regulator-max-microvolt = <2900000>;
 314         };
 315
 316         l9 {
 317                 regulator-min-microvolt = <3300000>;
 318                 regulator-max-microvolt = <3300000>;
 319         };
 320
 321         l10 {
 322                 regulator-min-microvolt = <2700000>;
 323                 regulator-max-microvolt = <2800000>;
 324         };
 325
 326         l11 {
 327                 regulator-min-microvolt = <1800000>;
 328                 regulator-max-microvolt = <2950000>;
 329                 regulator-allow-set-load;
 330                 regulator-system-load = <200000>;
 331         };
 332
 333         l12 {
 334                 regulator-min-microvolt = <1800000>;
 335                 regulator-max-microvolt = <2950000>;
 336         };
 337
 338         l13 {
 339                 regulator-min-microvolt = <3075000>;
 340                 regulator-max-microvolt = <3075000>;
 341         };
 342
 343         l14 {
 344                 regulator-min-microvolt = <1800000>;
 345                 regulator-max-microvolt = <3300000>;
 346         };
 347
 348         l15 {
 349                 regulator-min-microvolt = <1800000>;
 350                 regulator-max-microvolt = <3300000>;
 351         };
 352
 353         l16 {
 354                 regulator-min-microvolt = <1800000>;
 355                 regulator-max-microvolt = <3300000>;
 356         };
 357
 358         l17 {
 359                 regulator-min-microvolt = <2850000>;
 360                 regulator-max-microvolt = <2850000>;
 361         };
 362
 363         l18 {
 364                 regulator-min-microvolt = <2700000>;
 365                 regulator-max-microvolt = <2700000>;
 366         };
 367 };
 368
 369 &msmgpio {
 370         accel_int_default: accel-int-default {
 371                 pins = "gpio116";
 372                 function = "gpio";
 373
 374                 drive-strength = <2>;
 375                 bias-disable;
 376         };
 377
 378         camera_flash_default: camera-flash-default {
 379                 pins = "gpio31", "gpio32";
 380                 function = "gpio";
 381
 382                 drive-strength = <2>;
 383                 bias-disable;
 384         };
 385
 386         ctp_pwr_en_default: ctp-pwr-en-default {
 387                 pins = "gpio17";
 388                 function = "gpio";
 389
 390                 drive-strength = <2>;
 391                 bias-disable;
 392         };
 393
 394         gpio_keys_default: gpio-keys-default {
 395                 pins = "gpio107";
 396                 function = "gpio";
 397
 398                 drive-strength = <2>;
 399                 bias-pull-up;
 400         };
 401
 402         gyro_int_default: gyro-int-default {
 403                 pins = "gpio22", "gpio23";
 404                 function = "gpio";
 405
 406                 drive-strength = <2>;
 407                 bias-disable;
 408         };
 409
 410         light_int_default: light-int-default {
 411                 pins = "gpio115";
 412                 function = "gpio";
 413
 414                 drive-strength = <2>;
 415                 bias-disable;
 416         };
 417
 418         magn_int_default: magn-int-default {
 419                 pins = "gpio113";
 420                 function = "gpio";
 421
 422                 drive-strength = <2>;
 423                 bias-disable;
 424         };
 425
 426         tp_int_default: tp-int-default {
 427                 pins = "gpio13";
 428                 function = "gpio";
 429
 430                 drive-strength = <2>;
 431                 bias-disable;
 432         };
 433 };