1 # SPDX-License-Identifier: GPL-2.0
5 select ARCH_CLOCKSOURCE_DATA
6 select ARCH_DISCARD_MEMBLOCK if !HAVE_ARCH_PFN_VALID && !KEXEC
7 select ARCH_HAS_DEBUG_VIRTUAL if MMU
8 select ARCH_HAS_DEVMEM_IS_ALLOWED
9 select ARCH_HAS_ELF_RANDOMIZE
10 select ARCH_HAS_FORTIFY_SOURCE
12 select ARCH_HAS_MEMBARRIER_SYNC_CORE
13 select ARCH_HAS_PTE_SPECIAL if ARM_LPAE
14 select ARCH_HAS_PHYS_TO_DMA
15 select ARCH_HAS_SET_MEMORY
16 select ARCH_HAS_STRICT_KERNEL_RWX if MMU && !XIP_KERNEL
17 select ARCH_HAS_STRICT_MODULE_RWX if MMU
18 select ARCH_HAS_TICK_BROADCAST if GENERIC_CLOCKEVENTS_BROADCAST
19 select ARCH_HAVE_CUSTOM_GPIO_H
20 select ARCH_HAS_GCOV_PROFILE_ALL
21 select ARCH_MIGHT_HAVE_PC_PARPORT
22 select ARCH_OPTIONAL_KERNEL_RWX if ARCH_HAS_STRICT_KERNEL_RWX
23 select ARCH_OPTIONAL_KERNEL_RWX_DEFAULT if CPU_V7
24 select ARCH_SUPPORTS_ATOMIC_RMW
25 select ARCH_USE_BUILTIN_BSWAP
26 select ARCH_USE_CMPXCHG_LOCKREF
27 select ARCH_WANT_IPC_PARSE_VERSION
28 select BUILDTIME_EXTABLE_SORT if MMU
29 select CLONE_BACKWARDS
30 select CPU_PM if (SUSPEND || CPU_IDLE)
31 select DCACHE_WORD_ACCESS if HAVE_EFFICIENT_UNALIGNED_ACCESS
32 select DMA_DIRECT_OPS if !MMU
34 select EDAC_ATOMIC_SCRUB
35 select GENERIC_ALLOCATOR
36 select GENERIC_ARCH_TOPOLOGY if ARM_CPU_TOPOLOGY
37 select GENERIC_ATOMIC64 if (CPU_V7M || CPU_V6 || !CPU_32v6K || !AEABI)
38 select GENERIC_CLOCKEVENTS_BROADCAST if SMP
39 select GENERIC_CPU_AUTOPROBE
40 select GENERIC_EARLY_IOREMAP
41 select GENERIC_IDLE_POLL_SETUP
42 select GENERIC_IRQ_PROBE
43 select GENERIC_IRQ_SHOW
44 select GENERIC_IRQ_SHOW_LEVEL
45 select GENERIC_PCI_IOMAP
46 select GENERIC_SCHED_CLOCK
47 select GENERIC_SMP_IDLE_THREAD
48 select GENERIC_STRNCPY_FROM_USER
49 select GENERIC_STRNLEN_USER
50 select HANDLE_DOMAIN_IRQ
51 select HARDIRQS_SW_RESEND
52 select HAVE_ARCH_AUDITSYSCALL if (AEABI && !OABI_COMPAT)
53 select HAVE_ARCH_BITREVERSE if (CPU_32v7M || CPU_32v7) && !CPU_32v6
54 select HAVE_ARCH_JUMP_LABEL if !XIP_KERNEL && !CPU_ENDIAN_BE32 && MMU
55 select HAVE_ARCH_KGDB if !CPU_ENDIAN_BE32 && MMU
56 select HAVE_ARCH_MMAP_RND_BITS if MMU
57 select HAVE_ARCH_SECCOMP_FILTER if (AEABI && !OABI_COMPAT)
58 select HAVE_ARCH_THREAD_STRUCT_WHITELIST
59 select HAVE_ARCH_TRACEHOOK
60 select HAVE_ARM_SMCCC if CPU_V7
61 select HAVE_EBPF_JIT if !CPU_ENDIAN_BE32
62 select HAVE_CONTEXT_TRACKING
63 select HAVE_C_RECORDMCOUNT
64 select HAVE_DEBUG_KMEMLEAK
65 select HAVE_DMA_CONTIGUOUS if MMU
66 select HAVE_DYNAMIC_FTRACE if (!XIP_KERNEL) && !CPU_ENDIAN_BE32 && MMU
67 select HAVE_DYNAMIC_FTRACE_WITH_REGS if HAVE_DYNAMIC_FTRACE
68 select HAVE_EFFICIENT_UNALIGNED_ACCESS if (CPU_V6 || CPU_V6K || CPU_V7) && MMU
69 select HAVE_EXIT_THREAD
70 select HAVE_FTRACE_MCOUNT_RECORD if (!XIP_KERNEL)
71 select HAVE_FUNCTION_GRAPH_TRACER if (!THUMB2_KERNEL)
72 select HAVE_FUNCTION_TRACER if (!XIP_KERNEL)
73 select HAVE_GCC_PLUGINS
74 select HAVE_GENERIC_DMA_COHERENT
75 select HAVE_HW_BREAKPOINT if (PERF_EVENTS && (CPU_V6 || CPU_V6K || CPU_V7))
76 select HAVE_IDE if PCI || ISA || PCMCIA
77 select HAVE_IRQ_TIME_ACCOUNTING
78 select HAVE_KERNEL_GZIP
79 select HAVE_KERNEL_LZ4
80 select HAVE_KERNEL_LZMA
81 select HAVE_KERNEL_LZO
83 select HAVE_KPROBES if !XIP_KERNEL && !CPU_ENDIAN_BE32 && !CPU_V7M
84 select HAVE_KRETPROBES if (HAVE_KPROBES)
85 select HAVE_MOD_ARCH_SPECIFIC
87 select HAVE_OPROFILE if (HAVE_PERF_EVENTS)
88 select HAVE_OPTPROBES if !THUMB2_KERNEL
89 select HAVE_PERF_EVENTS
91 select HAVE_PERF_USER_STACK_DUMP
92 select HAVE_RCU_TABLE_FREE if (SMP && ARM_LPAE)
93 select HAVE_REGS_AND_STACK_ACCESS_API
95 select HAVE_STACKPROTECTOR
96 select HAVE_SYSCALL_TRACEPOINTS
98 select HAVE_VIRT_CPU_ACCOUNTING_GEN
99 select IRQ_FORCED_THREADING
100 select MODULES_USE_ELF_REL
101 select NEED_DMA_MAP_STATE
102 select OF_EARLY_FLATTREE if OF
103 select OF_RESERVED_MEM if OF
105 select OLD_SIGSUSPEND3
106 select PCI_SYSCALL if PCI
107 select PERF_USE_VMALLOC
110 select SYS_SUPPORTS_APM_EMULATION
111 # Above selects are sorted alphabetically; please add new ones
112 # according to that. Thanks.
114 The ARM series is a line of low-power-consumption RISC chip designs
115 licensed by ARM Ltd and targeted at embedded applications and
116 handhelds such as the Compaq IPAQ. ARM-based PCs are no longer
117 manufactured, but legacy ARM-based PC hardware remains popular in
118 Europe. There is an ARM Linux project with a web page at
119 <http://www.arm.linux.org.uk/>.
121 config ARM_HAS_SG_CHAIN
122 select ARCH_HAS_SG_CHAIN
125 config ARM_DMA_USE_IOMMU
127 select ARM_HAS_SG_CHAIN
128 select NEED_SG_DMA_LENGTH
132 config ARM_DMA_IOMMU_ALIGNMENT
133 int "Maximum PAGE_SIZE order of alignment for DMA IOMMU buffers"
137 DMA mapping framework by default aligns all buffers to the smallest
138 PAGE_SIZE order which is greater than or equal to the requested buffer
139 size. This works well for buffers up to a few hundreds kilobytes, but
140 for larger buffers it just a waste of address space. Drivers which has
141 relatively small addressing window (like 64Mib) might run out of
142 virtual space with just a few allocations.
144 With this parameter you can specify the maximum PAGE_SIZE order for
145 DMA IOMMU buffers. Larger buffers will be aligned only to this
146 specified order. The order is expressed as a power of two multiplied
151 config SYS_SUPPORTS_APM_EMULATION
156 select GENERIC_ALLOCATOR
167 The Extended Industry Standard Architecture (EISA) bus was
168 developed as an open alternative to the IBM MicroChannel bus.
170 The EISA bus provided some of the features of the IBM MicroChannel
171 bus while maintaining backward compatibility with cards made for
172 the older ISA bus. The EISA bus saw limited use between 1988 and
173 1995 when it was made obsolete by the PCI bus.
175 Say Y here if you are building a kernel for an EISA-based machine.
182 config STACKTRACE_SUPPORT
186 config LOCKDEP_SUPPORT
190 config TRACE_IRQFLAGS_SUPPORT
194 config RWSEM_XCHGADD_ALGORITHM
198 config ARCH_HAS_ILOG2_U32
201 config ARCH_HAS_ILOG2_U64
204 config ARCH_HAS_BANDGAP
207 config FIX_EARLYCON_MEM
210 config GENERIC_HWEIGHT
214 config GENERIC_CALIBRATE_DELAY
218 config ARCH_MAY_HAVE_PC_FDC
224 config ARCH_SUPPORTS_UPROBES
227 config ARCH_HAS_DMA_SET_COHERENT_MASK
230 config GENERIC_ISA_DMA
236 config NEED_RET_TO_USER
242 config ARM_PATCH_PHYS_VIRT
243 bool "Patch physical to virtual translations at runtime" if EMBEDDED
245 depends on !XIP_KERNEL && MMU
247 Patch phys-to-virt and virt-to-phys translation functions at
248 boot and module load time according to the position of the
249 kernel in system memory.
251 This can only be used with non-XIP MMU kernels where the base
252 of physical memory is at a 16MB boundary.
254 Only disable this option if you know that you do not require
255 this feature (eg, building a kernel for a single machine) and
256 you need to shrink the kernel to the minimal size.
258 config NEED_MACH_IO_H
261 Select this when mach/io.h is required to provide special
262 definitions for this platform. The need for mach/io.h should
263 be avoided when possible.
265 config NEED_MACH_MEMORY_H
268 Select this when mach/memory.h is required to provide special
269 definitions for this platform. The need for mach/memory.h should
270 be avoided when possible.
273 hex "Physical address of main memory" if MMU
274 depends on !ARM_PATCH_PHYS_VIRT
275 default DRAM_BASE if !MMU
276 default 0x00000000 if ARCH_EBSA110 || \
282 default 0x10000000 if ARCH_OMAP1 || ARCH_RPC
283 default 0x20000000 if ARCH_S5PV210
284 default 0xc0000000 if ARCH_SA1100
286 Please provide the physical address corresponding to the
287 location of main memory in your system.
293 config PGTABLE_LEVELS
295 default 3 if ARM_LPAE
301 bool "MMU-based Paged Memory Management Support"
304 Select if you want MMU-based virtualised addressing space
305 support by paged memory management. If unsure, say 'Y'.
307 config ARCH_MMAP_RND_BITS_MIN
310 config ARCH_MMAP_RND_BITS_MAX
311 default 14 if PAGE_OFFSET=0x40000000
312 default 15 if PAGE_OFFSET=0x80000000
316 # The "ARM system type" choice list is ordered alphabetically by option
317 # text. Please add new entries in the option alphabetic order.
320 prompt "ARM system type"
321 default ARM_SINGLE_ARMV7M if !MMU
322 default ARCH_MULTIPLATFORM if MMU
324 config ARCH_MULTIPLATFORM
325 bool "Allow multiple platforms to be selected"
327 select ARM_HAS_SG_CHAIN
328 select ARM_PATCH_PHYS_VIRT
332 select GENERIC_CLOCKEVENTS
333 select GENERIC_IRQ_MULTI_HANDLER
335 select PCI_DOMAINS_GENERIC if PCI
339 config ARM_SINGLE_ARMV7M
340 bool "ARMv7-M based platforms (Cortex-M0/M3/M4)"
347 select GENERIC_CLOCKEVENTS
354 select ARCH_USES_GETTIMEOFFSET
357 select NEED_MACH_IO_H
358 select NEED_MACH_MEMORY_H
361 This is an evaluation board for the StrongARM processor available
362 from Digital. It has limited hardware on-board, including an
363 Ethernet interface, two PCMCIA sockets, two serial ports and a
368 select ARCH_SPARSEMEM_ENABLE
370 imply ARM_PATCH_PHYS_VIRT
376 select GENERIC_CLOCKEVENTS
379 This enables support for the Cirrus EP93xx series of CPUs.
381 config ARCH_FOOTBRIDGE
385 select GENERIC_CLOCKEVENTS
387 select NEED_MACH_IO_H if !MMU
388 select NEED_MACH_MEMORY_H
390 Support for systems based on the DC21285 companion chip
391 ("FootBridge"), such as the Simtec CATS and the Rebel NetWinder.
394 bool "Hilscher NetX based"
398 select GENERIC_CLOCKEVENTS
400 This enables support for systems based on the Hilscher NetX Soc
406 select NEED_MACH_MEMORY_H
407 select NEED_RET_TO_USER
413 Support for Intel's IOP13XX (XScale) family of processors.
421 select NEED_RET_TO_USER
425 Support for Intel's 80219 and IOP32X (XScale) family of
434 select NEED_RET_TO_USER
438 Support for Intel's IOP33X (XScale) family of processors.
443 select ARCH_HAS_DMA_SET_COHERENT_MASK
444 select ARCH_SUPPORTS_BIG_ENDIAN
447 select DMABOUNCE if PCI
448 select GENERIC_CLOCKEVENTS
451 select NEED_MACH_IO_H
452 select USB_EHCI_BIG_ENDIAN_DESC
453 select USB_EHCI_BIG_ENDIAN_MMIO
455 Support for Intel's IXP4XX (XScale) family of processors.
460 select GENERIC_CLOCKEVENTS
461 select GENERIC_IRQ_MULTI_HANDLER
467 select PLAT_ORION_LEGACY
469 select PM_GENERIC_DOMAINS if PM
471 Support for the Marvell Dove SoC 88AP510
474 bool "Micrel/Kendin KS8695"
477 select GENERIC_CLOCKEVENTS
479 select NEED_MACH_MEMORY_H
481 Support for Micrel/Kendin KS8695 "Centaur" (ARM922T) based
482 System-on-Chip devices.
485 bool "Nuvoton W90X900 CPU"
489 select GENERIC_CLOCKEVENTS
492 Support for Nuvoton (Winbond logic dept.) ARM9 processor,
493 At present, the w90x900 has been renamed nuc900, regarding
494 the ARM series product line, you can login the following
495 link address to know more.
497 <http://www.nuvoton.com/hq/enu/ProductAndSales/ProductLines/
498 ConsumerElectronicsIC/ARMMicrocontroller/ARMMicrocontroller>
504 select CLKSRC_LPC32XX
507 select GENERIC_CLOCKEVENTS
508 select GENERIC_IRQ_MULTI_HANDLER
513 Support for the NXP LPC32XX family of processors
516 bool "PXA2xx/PXA3xx-based"
519 select ARM_CPU_SUSPEND if PM
526 select CPU_XSCALE if !CPU_XSC3
527 select GENERIC_CLOCKEVENTS
528 select GENERIC_IRQ_MULTI_HANDLER
536 Support for Intel/Marvell's PXA2xx/PXA3xx processor line.
542 select ARCH_MAY_HAVE_PC_FDC
543 select ARCH_SPARSEMEM_ENABLE
544 select ARCH_USES_GETTIMEOFFSET
548 select HAVE_PATA_PLATFORM
550 select NEED_MACH_IO_H
551 select NEED_MACH_MEMORY_H
554 On the Acorn Risc-PC, Linux can support the internal IDE disk and
555 CD-ROM interface, serial and parallel port, and the floppy drive.
560 select ARCH_SPARSEMEM_ENABLE
564 select TIMER_OF if OF
567 select GENERIC_CLOCKEVENTS
568 select GENERIC_IRQ_MULTI_HANDLER
573 select NEED_MACH_MEMORY_H
576 Support for StrongARM 11x0 based boards.
579 bool "Samsung S3C24XX SoCs"
582 select CLKSRC_SAMSUNG_PWM
583 select GENERIC_CLOCKEVENTS
586 select GENERIC_IRQ_MULTI_HANDLER
587 select HAVE_S3C2410_I2C if I2C
588 select HAVE_S3C2410_WATCHDOG if WATCHDOG
589 select HAVE_S3C_RTC if RTC_CLASS
590 select NEED_MACH_IO_H
594 Samsung S3C2410, S3C2412, S3C2413, S3C2416, S3C2440, S3C2442, S3C2443
595 and S3C2450 SoCs based systems, such as the Simtec Electronics BAST
596 (<http://www.simtec.co.uk/products/EB110ITX/>), the IPAQ 1940 or the
597 Samsung SMDK2410 development board (and derivatives).
601 select ARCH_HAS_HOLES_MEMORYMODEL
604 select GENERIC_ALLOCATOR
605 select GENERIC_CLOCKEVENTS
606 select GENERIC_IRQ_CHIP
609 select PM_GENERIC_DOMAINS if PM
610 select PM_GENERIC_DOMAINS_OF if PM && OF
611 select RESET_CONTROLLER
615 Support for TI's DaVinci platform.
620 select ARCH_HAS_HOLES_MEMORYMODEL
624 select GENERIC_CLOCKEVENTS
625 select GENERIC_IRQ_CHIP
626 select GENERIC_IRQ_MULTI_HANDLER
630 select NEED_MACH_IO_H if PCCARD
631 select NEED_MACH_MEMORY_H
634 Support for older TI OMAP1 (omap7xx, omap15xx or omap16xx)
638 menu "Multiple platform selection"
639 depends on ARCH_MULTIPLATFORM
641 comment "CPU Core family selection"
644 bool "ARMv4 based platforms (FA526)"
645 depends on !ARCH_MULTI_V6_V7
646 select ARCH_MULTI_V4_V5
649 config ARCH_MULTI_V4T
650 bool "ARMv4T based platforms (ARM720T, ARM920T, ...)"
651 depends on !ARCH_MULTI_V6_V7
652 select ARCH_MULTI_V4_V5
653 select CPU_ARM920T if !(CPU_ARM7TDMI || CPU_ARM720T || \
654 CPU_ARM740T || CPU_ARM9TDMI || CPU_ARM922T || \
655 CPU_ARM925T || CPU_ARM940T)
658 bool "ARMv5 based platforms (ARM926T, XSCALE, PJ1, ...)"
659 depends on !ARCH_MULTI_V6_V7
660 select ARCH_MULTI_V4_V5
661 select CPU_ARM926T if !(CPU_ARM946E || CPU_ARM1020 || \
662 CPU_ARM1020E || CPU_ARM1022 || CPU_ARM1026 || \
663 CPU_XSCALE || CPU_XSC3 || CPU_MOHAWK || CPU_FEROCEON)
665 config ARCH_MULTI_V4_V5
669 bool "ARMv6 based platforms (ARM11)"
670 select ARCH_MULTI_V6_V7
674 bool "ARMv7 based platforms (Cortex-A, PJ4, Scorpion, Krait)"
676 select ARCH_MULTI_V6_V7
680 config ARCH_MULTI_V6_V7
682 select MIGHT_HAVE_CACHE_L2X0
684 config ARCH_MULTI_CPU_AUTO
685 def_bool !(ARCH_MULTI_V4 || ARCH_MULTI_V4T || ARCH_MULTI_V6_V7)
691 bool "Dummy Virtual Machine"
692 depends on ARCH_MULTI_V7
695 select ARM_GIC_V2M if PCI
697 select ARM_GIC_V3_ITS if PCI
699 select HAVE_ARM_ARCH_TIMER
700 select ARCH_SUPPORTS_BIG_ENDIAN
703 # This is sorted alphabetically by mach-* pathname. However, plat-*
704 # Kconfigs may be included either alphabetically (according to the
705 # plat- suffix) or along side the corresponding mach-* source.
707 source "arch/arm/mach-actions/Kconfig"
709 source "arch/arm/mach-alpine/Kconfig"
711 source "arch/arm/mach-artpec/Kconfig"
713 source "arch/arm/mach-asm9260/Kconfig"
715 source "arch/arm/mach-aspeed/Kconfig"
717 source "arch/arm/mach-at91/Kconfig"
719 source "arch/arm/mach-axxia/Kconfig"
721 source "arch/arm/mach-bcm/Kconfig"
723 source "arch/arm/mach-berlin/Kconfig"
725 source "arch/arm/mach-clps711x/Kconfig"
727 source "arch/arm/mach-cns3xxx/Kconfig"
729 source "arch/arm/mach-davinci/Kconfig"
731 source "arch/arm/mach-digicolor/Kconfig"
733 source "arch/arm/mach-dove/Kconfig"
735 source "arch/arm/mach-ep93xx/Kconfig"
737 source "arch/arm/mach-exynos/Kconfig"
738 source "arch/arm/plat-samsung/Kconfig"
740 source "arch/arm/mach-footbridge/Kconfig"
742 source "arch/arm/mach-gemini/Kconfig"
744 source "arch/arm/mach-highbank/Kconfig"
746 source "arch/arm/mach-hisi/Kconfig"
748 source "arch/arm/mach-imx/Kconfig"
750 source "arch/arm/mach-integrator/Kconfig"
752 source "arch/arm/mach-iop13xx/Kconfig"
754 source "arch/arm/mach-iop32x/Kconfig"
756 source "arch/arm/mach-iop33x/Kconfig"
758 source "arch/arm/mach-ixp4xx/Kconfig"
760 source "arch/arm/mach-keystone/Kconfig"
762 source "arch/arm/mach-ks8695/Kconfig"
764 source "arch/arm/mach-mediatek/Kconfig"
766 source "arch/arm/mach-meson/Kconfig"
768 source "arch/arm/mach-mmp/Kconfig"
770 source "arch/arm/mach-moxart/Kconfig"
772 source "arch/arm/mach-mv78xx0/Kconfig"
774 source "arch/arm/mach-mvebu/Kconfig"
776 source "arch/arm/mach-mxs/Kconfig"
778 source "arch/arm/mach-netx/Kconfig"
780 source "arch/arm/mach-nomadik/Kconfig"
782 source "arch/arm/mach-npcm/Kconfig"
784 source "arch/arm/mach-nspire/Kconfig"
786 source "arch/arm/plat-omap/Kconfig"
788 source "arch/arm/mach-omap1/Kconfig"
790 source "arch/arm/mach-omap2/Kconfig"
792 source "arch/arm/mach-orion5x/Kconfig"
794 source "arch/arm/mach-oxnas/Kconfig"
796 source "arch/arm/mach-picoxcell/Kconfig"
798 source "arch/arm/mach-prima2/Kconfig"
800 source "arch/arm/mach-pxa/Kconfig"
801 source "arch/arm/plat-pxa/Kconfig"
803 source "arch/arm/mach-qcom/Kconfig"
805 source "arch/arm/mach-realview/Kconfig"
807 source "arch/arm/mach-rockchip/Kconfig"
809 source "arch/arm/mach-s3c24xx/Kconfig"
811 source "arch/arm/mach-s3c64xx/Kconfig"
813 source "arch/arm/mach-s5pv210/Kconfig"
815 source "arch/arm/mach-sa1100/Kconfig"
817 source "arch/arm/mach-shmobile/Kconfig"
819 source "arch/arm/mach-socfpga/Kconfig"
821 source "arch/arm/mach-spear/Kconfig"
823 source "arch/arm/mach-sti/Kconfig"
825 source "arch/arm/mach-stm32/Kconfig"
827 source "arch/arm/mach-sunxi/Kconfig"
829 source "arch/arm/mach-tango/Kconfig"
831 source "arch/arm/mach-tegra/Kconfig"
833 source "arch/arm/mach-u300/Kconfig"
835 source "arch/arm/mach-uniphier/Kconfig"
837 source "arch/arm/mach-ux500/Kconfig"
839 source "arch/arm/mach-versatile/Kconfig"
841 source "arch/arm/mach-vexpress/Kconfig"
842 source "arch/arm/plat-versatile/Kconfig"
844 source "arch/arm/mach-vt8500/Kconfig"
846 source "arch/arm/mach-w90x900/Kconfig"
848 source "arch/arm/mach-zx/Kconfig"
850 source "arch/arm/mach-zynq/Kconfig"
852 # ARMv7-M architecture
854 bool "Energy Micro efm32"
855 depends on ARM_SINGLE_ARMV7M
858 Support for Energy Micro's (now Silicon Labs) efm32 Giant Gecko
862 bool "NXP LPC18xx/LPC43xx"
863 depends on ARM_SINGLE_ARMV7M
864 select ARCH_HAS_RESET_CONTROLLER
866 select CLKSRC_LPC32XX
869 Support for NXP's LPC18xx Cortex-M3 and LPC43xx Cortex-M4
870 high performance microcontrollers.
873 bool "ARM MPS2 platform"
874 depends on ARM_SINGLE_ARMV7M
878 Support for Cortex-M Prototyping System (or V2M-MPS2) which comes
879 with a range of available cores like Cortex-M3/M4/M7.
881 Please, note that depends which Application Note is used memory map
882 for the platform may vary, so adjustment of RAM base might be needed.
884 # Definitions to make life easier
890 select GENERIC_CLOCKEVENTS
896 select GENERIC_IRQ_CHIP
899 config PLAT_ORION_LEGACY
906 config PLAT_VERSATILE
909 source "arch/arm/firmware/Kconfig"
911 source arch/arm/mm/Kconfig
914 bool "Enable iWMMXt support"
915 depends on CPU_XSCALE || CPU_XSC3 || CPU_MOHAWK || CPU_PJ4 || CPU_PJ4B
916 default y if PXA27x || PXA3xx || ARCH_MMP || CPU_PJ4 || CPU_PJ4B
918 Enable support for iWMMXt context switching at run time if
919 running on a CPU that supports it.
922 source "arch/arm/Kconfig-nommu"
925 config PJ4B_ERRATA_4742
926 bool "PJ4B Errata 4742: IDLE Wake Up Commands can Cause the CPU Core to Cease Operation"
927 depends on CPU_PJ4B && MACH_ARMADA_370
930 When coming out of either a Wait for Interrupt (WFI) or a Wait for
931 Event (WFE) IDLE states, a specific timing sensitivity exists between
932 the retiring WFI/WFE instructions and the newly issued subsequent
933 instructions. This sensitivity can result in a CPU hang scenario.
935 The software must insert either a Data Synchronization Barrier (DSB)
936 or Data Memory Barrier (DMB) command immediately after the WFI/WFE
939 config ARM_ERRATA_326103
940 bool "ARM errata: FSR write bit incorrect on a SWP to read-only memory"
943 Executing a SWP instruction to read-only memory does not set bit 11
944 of the FSR on the ARM 1136 prior to r1p0. This causes the kernel to
945 treat the access as a read, preventing a COW from occurring and
946 causing the faulting task to livelock.
948 config ARM_ERRATA_411920
949 bool "ARM errata: Invalidation of the Instruction Cache operation can fail"
950 depends on CPU_V6 || CPU_V6K
952 Invalidation of the Instruction Cache operation can
953 fail. This erratum is present in 1136 (before r1p4), 1156 and 1176.
954 It does not affect the MPCore. This option enables the ARM Ltd.
955 recommended workaround.
957 config ARM_ERRATA_430973
958 bool "ARM errata: Stale prediction on replaced interworking branch"
961 This option enables the workaround for the 430973 Cortex-A8
962 r1p* erratum. If a code sequence containing an ARM/Thumb
963 interworking branch is replaced with another code sequence at the
964 same virtual address, whether due to self-modifying code or virtual
965 to physical address re-mapping, Cortex-A8 does not recover from the
966 stale interworking branch prediction. This results in Cortex-A8
967 executing the new code sequence in the incorrect ARM or Thumb state.
968 The workaround enables the BTB/BTAC operations by setting ACTLR.IBE
969 and also flushes the branch target cache at every context switch.
970 Note that setting specific bits in the ACTLR register may not be
971 available in non-secure mode.
973 config ARM_ERRATA_458693
974 bool "ARM errata: Processor deadlock when a false hazard is created"
976 depends on !ARCH_MULTIPLATFORM
978 This option enables the workaround for the 458693 Cortex-A8 (r2p0)
979 erratum. For very specific sequences of memory operations, it is
980 possible for a hazard condition intended for a cache line to instead
981 be incorrectly associated with a different cache line. This false
982 hazard might then cause a processor deadlock. The workaround enables
983 the L1 caching of the NEON accesses and disables the PLD instruction
984 in the ACTLR register. Note that setting specific bits in the ACTLR
985 register may not be available in non-secure mode.
987 config ARM_ERRATA_460075
988 bool "ARM errata: Data written to the L2 cache can be overwritten with stale data"
990 depends on !ARCH_MULTIPLATFORM
992 This option enables the workaround for the 460075 Cortex-A8 (r2p0)
993 erratum. Any asynchronous access to the L2 cache may encounter a
994 situation in which recent store transactions to the L2 cache are lost
995 and overwritten with stale memory contents from external memory. The
996 workaround disables the write-allocate mode for the L2 cache via the
997 ACTLR register. Note that setting specific bits in the ACTLR register
998 may not be available in non-secure mode.
1000 config ARM_ERRATA_742230
1001 bool "ARM errata: DMB operation may be faulty"
1002 depends on CPU_V7 && SMP
1003 depends on !ARCH_MULTIPLATFORM
1005 This option enables the workaround for the 742230 Cortex-A9
1006 (r1p0..r2p2) erratum. Under rare circumstances, a DMB instruction
1007 between two write operations may not ensure the correct visibility
1008 ordering of the two writes. This workaround sets a specific bit in
1009 the diagnostic register of the Cortex-A9 which causes the DMB
1010 instruction to behave as a DSB, ensuring the correct behaviour of
1013 config ARM_ERRATA_742231
1014 bool "ARM errata: Incorrect hazard handling in the SCU may lead to data corruption"
1015 depends on CPU_V7 && SMP
1016 depends on !ARCH_MULTIPLATFORM
1018 This option enables the workaround for the 742231 Cortex-A9
1019 (r2p0..r2p2) erratum. Under certain conditions, specific to the
1020 Cortex-A9 MPCore micro-architecture, two CPUs working in SMP mode,
1021 accessing some data located in the same cache line, may get corrupted
1022 data due to bad handling of the address hazard when the line gets
1023 replaced from one of the CPUs at the same time as another CPU is
1024 accessing it. This workaround sets specific bits in the diagnostic
1025 register of the Cortex-A9 which reduces the linefill issuing
1026 capabilities of the processor.
1028 config ARM_ERRATA_643719
1029 bool "ARM errata: LoUIS bit field in CLIDR register is incorrect"
1030 depends on CPU_V7 && SMP
1033 This option enables the workaround for the 643719 Cortex-A9 (prior to
1034 r1p0) erratum. On affected cores the LoUIS bit field of the CLIDR
1035 register returns zero when it should return one. The workaround
1036 corrects this value, ensuring cache maintenance operations which use
1037 it behave as intended and avoiding data corruption.
1039 config ARM_ERRATA_720789
1040 bool "ARM errata: TLBIASIDIS and TLBIMVAIS operations can broadcast a faulty ASID"
1043 This option enables the workaround for the 720789 Cortex-A9 (prior to
1044 r2p0) erratum. A faulty ASID can be sent to the other CPUs for the
1045 broadcasted CP15 TLB maintenance operations TLBIASIDIS and TLBIMVAIS.
1046 As a consequence of this erratum, some TLB entries which should be
1047 invalidated are not, resulting in an incoherency in the system page
1048 tables. The workaround changes the TLB flushing routines to invalidate
1049 entries regardless of the ASID.
1051 config ARM_ERRATA_743622
1052 bool "ARM errata: Faulty hazard checking in the Store Buffer may lead to data corruption"
1054 depends on !ARCH_MULTIPLATFORM
1056 This option enables the workaround for the 743622 Cortex-A9
1057 (r2p*) erratum. Under very rare conditions, a faulty
1058 optimisation in the Cortex-A9 Store Buffer may lead to data
1059 corruption. This workaround sets a specific bit in the diagnostic
1060 register of the Cortex-A9 which disables the Store Buffer
1061 optimisation, preventing the defect from occurring. This has no
1062 visible impact on the overall performance or power consumption of the
1065 config ARM_ERRATA_751472
1066 bool "ARM errata: Interrupted ICIALLUIS may prevent completion of broadcasted operation"
1068 depends on !ARCH_MULTIPLATFORM
1070 This option enables the workaround for the 751472 Cortex-A9 (prior
1071 to r3p0) erratum. An interrupted ICIALLUIS operation may prevent the
1072 completion of a following broadcasted operation if the second
1073 operation is received by a CPU before the ICIALLUIS has completed,
1074 potentially leading to corrupted entries in the cache or TLB.
1076 config ARM_ERRATA_754322
1077 bool "ARM errata: possible faulty MMU translations following an ASID switch"
1080 This option enables the workaround for the 754322 Cortex-A9 (r2p*,
1081 r3p*) erratum. A speculative memory access may cause a page table walk
1082 which starts prior to an ASID switch but completes afterwards. This
1083 can populate the micro-TLB with a stale entry which may be hit with
1084 the new ASID. This workaround places two dsb instructions in the mm
1085 switching code so that no page table walks can cross the ASID switch.
1087 config ARM_ERRATA_754327
1088 bool "ARM errata: no automatic Store Buffer drain"
1089 depends on CPU_V7 && SMP
1091 This option enables the workaround for the 754327 Cortex-A9 (prior to
1092 r2p0) erratum. The Store Buffer does not have any automatic draining
1093 mechanism and therefore a livelock may occur if an external agent
1094 continuously polls a memory location waiting to observe an update.
1095 This workaround defines cpu_relax() as smp_mb(), preventing correctly
1096 written polling loops from denying visibility of updates to memory.
1098 config ARM_ERRATA_364296
1099 bool "ARM errata: Possible cache data corruption with hit-under-miss enabled"
1102 This options enables the workaround for the 364296 ARM1136
1103 r0p2 erratum (possible cache data corruption with
1104 hit-under-miss enabled). It sets the undocumented bit 31 in
1105 the auxiliary control register and the FI bit in the control
1106 register, thus disabling hit-under-miss without putting the
1107 processor into full low interrupt latency mode. ARM11MPCore
1110 config ARM_ERRATA_764369
1111 bool "ARM errata: Data cache line maintenance operation by MVA may not succeed"
1112 depends on CPU_V7 && SMP
1114 This option enables the workaround for erratum 764369
1115 affecting Cortex-A9 MPCore with two or more processors (all
1116 current revisions). Under certain timing circumstances, a data
1117 cache line maintenance operation by MVA targeting an Inner
1118 Shareable memory region may fail to proceed up to either the
1119 Point of Coherency or to the Point of Unification of the
1120 system. This workaround adds a DSB instruction before the
1121 relevant cache maintenance functions and sets a specific bit
1122 in the diagnostic control register of the SCU.
1124 config ARM_ERRATA_775420
1125 bool "ARM errata: A data cache maintenance operation which aborts, might lead to deadlock"
1128 This option enables the workaround for the 775420 Cortex-A9 (r2p2,
1129 r2p6,r2p8,r2p10,r3p0) erratum. In case a date cache maintenance
1130 operation aborts with MMU exception, it might cause the processor
1131 to deadlock. This workaround puts DSB before executing ISB if
1132 an abort may occur on cache maintenance.
1134 config ARM_ERRATA_798181
1135 bool "ARM errata: TLBI/DSB failure on Cortex-A15"
1136 depends on CPU_V7 && SMP
1138 On Cortex-A15 (r0p0..r3p2) the TLBI*IS/DSB operations are not
1139 adequately shooting down all use of the old entries. This
1140 option enables the Linux kernel workaround for this erratum
1141 which sends an IPI to the CPUs that are running the same ASID
1142 as the one being invalidated.
1144 config ARM_ERRATA_773022
1145 bool "ARM errata: incorrect instructions may be executed from loop buffer"
1148 This option enables the workaround for the 773022 Cortex-A15
1149 (up to r0p4) erratum. In certain rare sequences of code, the
1150 loop buffer may deliver incorrect instructions. This
1151 workaround disables the loop buffer to avoid the erratum.
1153 config ARM_ERRATA_818325_852422
1154 bool "ARM errata: A12: some seqs of opposed cond code instrs => deadlock or corruption"
1157 This option enables the workaround for:
1158 - Cortex-A12 818325: Execution of an UNPREDICTABLE STR or STM
1159 instruction might deadlock. Fixed in r0p1.
1160 - Cortex-A12 852422: Execution of a sequence of instructions might
1161 lead to either a data corruption or a CPU deadlock. Not fixed in
1162 any Cortex-A12 cores yet.
1163 This workaround for all both errata involves setting bit[12] of the
1164 Feature Register. This bit disables an optimisation applied to a
1165 sequence of 2 instructions that use opposing condition codes.
1167 config ARM_ERRATA_821420
1168 bool "ARM errata: A12: sequence of VMOV to core registers might lead to a dead lock"
1171 This option enables the workaround for the 821420 Cortex-A12
1172 (all revs) erratum. In very rare timing conditions, a sequence
1173 of VMOV to Core registers instructions, for which the second
1174 one is in the shadow of a branch or abort, can lead to a
1175 deadlock when the VMOV instructions are issued out-of-order.
1177 config ARM_ERRATA_825619
1178 bool "ARM errata: A12: DMB NSHST/ISHST mixed ... might cause deadlock"
1181 This option enables the workaround for the 825619 Cortex-A12
1182 (all revs) erratum. Within rare timing constraints, executing a
1183 DMB NSHST or DMB ISHST instruction followed by a mix of Cacheable
1184 and Device/Strongly-Ordered loads and stores might cause deadlock
1186 config ARM_ERRATA_852421
1187 bool "ARM errata: A17: DMB ST might fail to create order between stores"
1190 This option enables the workaround for the 852421 Cortex-A17
1191 (r1p0, r1p1, r1p2) erratum. Under very rare timing conditions,
1192 execution of a DMB ST instruction might fail to properly order
1193 stores from GroupA and stores from GroupB.
1195 config ARM_ERRATA_852423
1196 bool "ARM errata: A17: some seqs of opposed cond code instrs => deadlock or corruption"
1199 This option enables the workaround for:
1200 - Cortex-A17 852423: Execution of a sequence of instructions might
1201 lead to either a data corruption or a CPU deadlock. Not fixed in
1202 any Cortex-A17 cores yet.
1203 This is identical to Cortex-A12 erratum 852422. It is a separate
1204 config option from the A12 erratum due to the way errata are checked
1209 source "arch/arm/common/Kconfig"
1216 Find out whether you have ISA slots on your motherboard. ISA is the
1217 name of a bus system, i.e. the way the CPU talks to the other stuff
1218 inside your box. Other bus systems are PCI, EISA, MicroChannel
1219 (MCA) or VESA. ISA is an older system, now being displaced by PCI;
1220 newer boards don't support it. If you have ISA, say Y, otherwise N.
1222 # Select ISA DMA controller support
1227 # Select ISA DMA interface
1231 config PCI_NANOENGINE
1232 bool "BSE nanoEngine PCI support"
1233 depends on SA1100_NANOENGINE
1235 Enable PCI on the BSE nanoEngine board.
1237 config PCI_HOST_ITE8152
1239 depends on PCI && MACH_ARMCORE
1243 source "drivers/pcmcia/Kconfig"
1247 menu "Kernel Features"
1252 This option should be selected by machines which have an SMP-
1255 The only effect of this option is to make the SMP-related
1256 options available to the user for configuration.
1259 bool "Symmetric Multi-Processing"
1260 depends on CPU_V6K || CPU_V7
1261 depends on GENERIC_CLOCKEVENTS
1263 depends on MMU || ARM_MPU
1266 This enables support for systems with more than one CPU. If you have
1267 a system with only one CPU, say N. If you have a system with more
1268 than one CPU, say Y.
1270 If you say N here, the kernel will run on uni- and multiprocessor
1271 machines, but will use only one CPU of a multiprocessor machine. If
1272 you say Y here, the kernel will run on many, but not all,
1273 uniprocessor machines. On a uniprocessor machine, the kernel
1274 will run faster if you say N here.
1276 See also <file:Documentation/x86/i386/IO-APIC.txt>,
1277 <file:Documentation/lockup-watchdogs.txt> and the SMP-HOWTO available at
1278 <http://tldp.org/HOWTO/SMP-HOWTO.html>.
1280 If you don't know what to do here, say N.
1283 bool "Allow booting SMP kernel on uniprocessor systems"
1284 depends on SMP && !XIP_KERNEL && MMU
1287 SMP kernels contain instructions which fail on non-SMP processors.
1288 Enabling this option allows the kernel to modify itself to make
1289 these instructions safe. Disabling it allows about 1K of space
1292 If you don't know what to do here, say Y.
1294 config ARM_CPU_TOPOLOGY
1295 bool "Support cpu topology definition"
1296 depends on SMP && CPU_V7
1299 Support ARM cpu topology definition. The MPIDR register defines
1300 affinity between processors which is then used to describe the cpu
1301 topology of an ARM System.
1304 bool "Multi-core scheduler support"
1305 depends on ARM_CPU_TOPOLOGY
1307 Multi-core scheduler support improves the CPU scheduler's decision
1308 making when dealing with multi-core CPU chips at a cost of slightly
1309 increased overhead in some places. If unsure say N here.
1312 bool "SMT scheduler support"
1313 depends on ARM_CPU_TOPOLOGY
1315 Improves the CPU scheduler's decision making when dealing with
1316 MultiThreading at a cost of slightly increased overhead in some
1317 places. If unsure say N here.
1322 This option enables support for the ARM system coherency unit
1324 config HAVE_ARM_ARCH_TIMER
1325 bool "Architected timer support"
1327 select ARM_ARCH_TIMER
1328 select GENERIC_CLOCKEVENTS
1330 This option enables support for the ARM architected timer
1334 select TIMER_OF if OF
1336 This options enables support for the ARM timer and watchdog unit
1339 bool "Multi-Cluster Power Management"
1340 depends on CPU_V7 && SMP
1342 This option provides the common power management infrastructure
1343 for (multi-)cluster based systems, such as big.LITTLE based
1346 config MCPM_QUAD_CLUSTER
1350 To avoid wasting resources unnecessarily, MCPM only supports up
1351 to 2 clusters by default.
1352 Platforms with 3 or 4 clusters that use MCPM must select this
1353 option to allow the additional clusters to be managed.
1356 bool "big.LITTLE support (Experimental)"
1357 depends on CPU_V7 && SMP
1360 This option enables support selections for the big.LITTLE
1361 system architecture.
1364 bool "big.LITTLE switcher support"
1365 depends on BIG_LITTLE && MCPM && HOTPLUG_CPU && ARM_GIC
1368 The big.LITTLE "switcher" provides the core functionality to
1369 transparently handle transition between a cluster of A15's
1370 and a cluster of A7's in a big.LITTLE system.
1372 config BL_SWITCHER_DUMMY_IF
1373 tristate "Simple big.LITTLE switcher user interface"
1374 depends on BL_SWITCHER && DEBUG_KERNEL
1376 This is a simple and dummy char dev interface to control
1377 the big.LITTLE switcher core code. It is meant for
1378 debugging purposes only.
1381 prompt "Memory split"
1385 Select the desired split between kernel and user memory.
1387 If you are not absolutely sure what you are doing, leave this
1391 bool "3G/1G user/kernel split"
1392 config VMSPLIT_3G_OPT
1393 depends on !ARM_LPAE
1394 bool "3G/1G user/kernel split (for full 1G low memory)"
1396 bool "2G/2G user/kernel split"
1398 bool "1G/3G user/kernel split"
1403 default PHYS_OFFSET if !MMU
1404 default 0x40000000 if VMSPLIT_1G
1405 default 0x80000000 if VMSPLIT_2G
1406 default 0xB0000000 if VMSPLIT_3G_OPT
1410 int "Maximum number of CPUs (2-32)"
1416 bool "Support for hot-pluggable CPUs"
1419 Say Y here to experiment with turning CPUs off and on. CPUs
1420 can be controlled through /sys/devices/system/cpu.
1423 bool "Support for the ARM Power State Coordination Interface (PSCI)"
1424 depends on HAVE_ARM_SMCCC
1427 Say Y here if you want Linux to communicate with system firmware
1428 implementing the PSCI specification for CPU-centric power
1429 management operations described in ARM document number ARM DEN
1430 0022A ("Power State Coordination Interface System Software on
1433 # The GPIO number here must be sorted by descending number. In case of
1434 # a multiplatform kernel, we just want the highest value required by the
1435 # selected platforms.
1438 default 2048 if ARCH_SOCFPGA
1439 default 1024 if ARCH_BRCMSTB || ARCH_RENESAS || ARCH_TEGRA || \
1441 default 512 if ARCH_EXYNOS || ARCH_KEYSTONE || SOC_OMAP5 || \
1442 SOC_DRA7XX || ARCH_S3C24XX || ARCH_S3C64XX || ARCH_S5PV210
1443 default 416 if ARCH_SUNXI
1444 default 392 if ARCH_U8500
1445 default 352 if ARCH_VT8500
1446 default 288 if ARCH_ROCKCHIP
1447 default 264 if MACH_H4700
1450 Maximum number of GPIOs in the system.
1452 If unsure, leave the default value.
1456 default 200 if ARCH_EBSA110
1457 default 128 if SOC_AT91RM9200
1461 depends on HZ_FIXED = 0
1462 prompt "Timer frequency"
1486 default HZ_FIXED if HZ_FIXED != 0
1487 default 100 if HZ_100
1488 default 200 if HZ_200
1489 default 250 if HZ_250
1490 default 300 if HZ_300
1491 default 500 if HZ_500
1495 def_bool HIGH_RES_TIMERS
1497 config THUMB2_KERNEL
1498 bool "Compile the kernel in Thumb-2 mode" if !CPU_THUMBONLY
1499 depends on (CPU_V7 || CPU_V7M) && !CPU_V6 && !CPU_V6K
1500 default y if CPU_THUMBONLY
1503 By enabling this option, the kernel will be compiled in
1508 config THUMB2_AVOID_R_ARM_THM_JUMP11
1509 bool "Work around buggy Thumb-2 short branch relocations in gas"
1510 depends on THUMB2_KERNEL && MODULES
1513 Various binutils versions can resolve Thumb-2 branches to
1514 locally-defined, preemptible global symbols as short-range "b.n"
1515 branch instructions.
1517 This is a problem, because there's no guarantee the final
1518 destination of the symbol, or any candidate locations for a
1519 trampoline, are within range of the branch. For this reason, the
1520 kernel does not support fixing up the R_ARM_THM_JUMP11 (102)
1521 relocation in modules at all, and it makes little sense to add
1524 The symptom is that the kernel fails with an "unsupported
1525 relocation" error when loading some modules.
1527 Until fixed tools are available, passing
1528 -fno-optimize-sibling-calls to gcc should prevent gcc generating
1529 code which hits this problem, at the cost of a bit of extra runtime
1530 stack usage in some cases.
1532 The problem is described in more detail at:
1533 https://bugs.launchpad.net/binutils-linaro/+bug/725126
1535 Only Thumb-2 kernels are affected.
1537 Unless you are sure your tools don't have this problem, say Y.
1539 config ARM_PATCH_IDIV
1540 bool "Runtime patch udiv/sdiv instructions into __aeabi_{u}idiv()"
1541 depends on CPU_32v7 && !XIP_KERNEL
1544 The ARM compiler inserts calls to __aeabi_idiv() and
1545 __aeabi_uidiv() when it needs to perform division on signed
1546 and unsigned integers. Some v7 CPUs have support for the sdiv
1547 and udiv instructions that can be used to implement those
1550 Enabling this option allows the kernel to modify itself to
1551 replace the first two instructions of these library functions
1552 with the sdiv or udiv plus "bx lr" instructions when the CPU
1553 it is running on supports them. Typically this will be faster
1554 and less power intensive than running the original library
1555 code to do integer division.
1558 bool "Use the ARM EABI to compile the kernel" if !CPU_V7 && !CPU_V7M && !CPU_V6 && !CPU_V6K
1559 default CPU_V7 || CPU_V7M || CPU_V6 || CPU_V6K
1561 This option allows for the kernel to be compiled using the latest
1562 ARM ABI (aka EABI). This is only useful if you are using a user
1563 space environment that is also compiled with EABI.
1565 Since there are major incompatibilities between the legacy ABI and
1566 EABI, especially with regard to structure member alignment, this
1567 option also changes the kernel syscall calling convention to
1568 disambiguate both ABIs and allow for backward compatibility support
1569 (selected with CONFIG_OABI_COMPAT).
1571 To use this you need GCC version 4.0.0 or later.
1574 bool "Allow old ABI binaries to run with this kernel (EXPERIMENTAL)"
1575 depends on AEABI && !THUMB2_KERNEL
1577 This option preserves the old syscall interface along with the
1578 new (ARM EABI) one. It also provides a compatibility layer to
1579 intercept syscalls that have structure arguments which layout
1580 in memory differs between the legacy ABI and the new ARM EABI
1581 (only for non "thumb" binaries). This option adds a tiny
1582 overhead to all syscalls and produces a slightly larger kernel.
1584 The seccomp filter system will not be available when this is
1585 selected, since there is no way yet to sensibly distinguish
1586 between calling conventions during filtering.
1588 If you know you'll be using only pure EABI user space then you
1589 can say N here. If this option is not selected and you attempt
1590 to execute a legacy ABI binary then the result will be
1591 UNPREDICTABLE (in fact it can be predicted that it won't work
1592 at all). If in doubt say N.
1594 config ARCH_HAS_HOLES_MEMORYMODEL
1597 config ARCH_SPARSEMEM_ENABLE
1600 config ARCH_SPARSEMEM_DEFAULT
1601 def_bool ARCH_SPARSEMEM_ENABLE
1603 config ARCH_SELECT_MEMORY_MODEL
1604 def_bool ARCH_SPARSEMEM_ENABLE
1606 config HAVE_ARCH_PFN_VALID
1607 def_bool ARCH_HAS_HOLES_MEMORYMODEL || !SPARSEMEM
1609 config HAVE_GENERIC_GUP
1614 bool "High Memory Support"
1617 The address space of ARM processors is only 4 Gigabytes large
1618 and it has to accommodate user address space, kernel address
1619 space as well as some memory mapped IO. That means that, if you
1620 have a large amount of physical memory and/or IO, not all of the
1621 memory can be "permanently mapped" by the kernel. The physical
1622 memory that is not permanently mapped is called "high memory".
1624 Depending on the selected kernel/user memory split, minimum
1625 vmalloc space and actual amount of RAM, you may not need this
1626 option which should result in a slightly faster kernel.
1631 bool "Allocate 2nd-level pagetables from highmem" if EXPERT
1635 The VM uses one page of physical memory for each page table.
1636 For systems with a lot of processes, this can use a lot of
1637 precious low memory, eventually leading to low memory being
1638 consumed by page tables. Setting this option will allow
1639 user-space 2nd level page tables to reside in high memory.
1641 config CPU_SW_DOMAIN_PAN
1642 bool "Enable use of CPU domains to implement privileged no-access"
1643 depends on MMU && !ARM_LPAE
1646 Increase kernel security by ensuring that normal kernel accesses
1647 are unable to access userspace addresses. This can help prevent
1648 use-after-free bugs becoming an exploitable privilege escalation
1649 by ensuring that magic values (such as LIST_POISON) will always
1650 fault when dereferenced.
1652 CPUs with low-vector mappings use a best-efforts implementation.
1653 Their lower 1MB needs to remain accessible for the vectors, but
1654 the remainder of userspace will become appropriately inaccessible.
1656 config HW_PERF_EVENTS
1660 config SYS_SUPPORTS_HUGETLBFS
1664 config HAVE_ARCH_TRANSPARENT_HUGEPAGE
1668 config ARCH_WANT_GENERAL_HUGETLB
1671 config ARM_MODULE_PLTS
1672 bool "Use PLTs to allow module memory to spill over into vmalloc area"
1676 Allocate PLTs when loading modules so that jumps and calls whose
1677 targets are too far away for their relative offsets to be encoded
1678 in the instructions themselves can be bounced via veneers in the
1679 module's PLT. This allows modules to be allocated in the generic
1680 vmalloc area after the dedicated module memory area has been
1681 exhausted. The modules will use slightly more memory, but after
1682 rounding up to page size, the actual memory footprint is usually
1685 Disabling this is usually safe for small single-platform
1686 configurations. If unsure, say y.
1688 config FORCE_MAX_ZONEORDER
1689 int "Maximum zone order"
1690 default "12" if SOC_AM33XX
1691 default "9" if SA1111 || ARCH_EFM32
1694 The kernel memory allocator divides physically contiguous memory
1695 blocks into "zones", where each zone is a power of two number of
1696 pages. This option selects the largest power of two that the kernel
1697 keeps in the memory allocator. If you need to allocate very large
1698 blocks of physically contiguous memory, then you may need to
1699 increase this value.
1701 This config option is actually maximum order plus one. For example,
1702 a value of 11 means that the largest free memory block is 2^10 pages.
1704 config ALIGNMENT_TRAP
1706 depends on CPU_CP15_MMU
1707 default y if !ARCH_EBSA110
1708 select HAVE_PROC_CPU if PROC_FS
1710 ARM processors cannot fetch/store information which is not
1711 naturally aligned on the bus, i.e., a 4 byte fetch must start at an
1712 address divisible by 4. On 32-bit ARM processors, these non-aligned
1713 fetch/store instructions will be emulated in software if you say
1714 here, which has a severe performance impact. This is necessary for
1715 correct operation of some network protocols. With an IP-only
1716 configuration it is safe to say N, otherwise say Y.
1718 config UACCESS_WITH_MEMCPY
1719 bool "Use kernel mem{cpy,set}() for {copy_to,clear}_user()"
1721 default y if CPU_FEROCEON
1723 Implement faster copy_to_user and clear_user methods for CPU
1724 cores where a 8-word STM instruction give significantly higher
1725 memory write throughput than a sequence of individual 32bit stores.
1727 A possible side effect is a slight increase in scheduling latency
1728 between threads sharing the same address space if they invoke
1729 such copy operations with large buffers.
1731 However, if the CPU data cache is using a write-allocate mode,
1732 this option is unlikely to provide any performance gain.
1736 prompt "Enable seccomp to safely compute untrusted bytecode"
1738 This kernel feature is useful for number crunching applications
1739 that may need to compute untrusted bytecode during their
1740 execution. By using pipes or other transports made available to
1741 the process as file descriptors supporting the read/write
1742 syscalls, it's possible to isolate those applications in
1743 their own address space using seccomp. Once seccomp is
1744 enabled via prctl(PR_SET_SECCOMP), it cannot be disabled
1745 and the task is only allowed to execute a few safe syscalls
1746 defined by each seccomp mode.
1749 bool "Enable paravirtualization code"
1751 This changes the kernel so it can modify itself when it is run
1752 under a hypervisor, potentially improving performance significantly
1753 over full virtualization.
1755 config PARAVIRT_TIME_ACCOUNTING
1756 bool "Paravirtual steal time accounting"
1760 Select this option to enable fine granularity task steal time
1761 accounting. Time spent executing other tasks in parallel with
1762 the current vCPU is discounted from the vCPU power. To account for
1763 that, there can be a small performance impact.
1765 If in doubt, say N here.
1772 bool "Xen guest support on ARM"
1773 depends on ARM && AEABI && OF
1774 depends on CPU_V7 && !CPU_V6
1775 depends on !GENERIC_ATOMIC64
1777 select ARCH_DMA_ADDR_T_64BIT
1783 Say Y if you want to run Linux in a Virtual Machine on Xen on ARM.
1790 bool "Flattened Device Tree support"
1794 Include support for flattened device tree machine descriptions.
1797 bool "Support for the traditional ATAGS boot data passing" if USE_OF
1800 This is the traditional way of passing data to the kernel at boot
1801 time. If you are solely relying on the flattened device tree (or
1802 the ARM_ATAG_DTB_COMPAT option) then you may unselect this option
1803 to remove ATAGS support from your kernel binary. If unsure,
1806 config DEPRECATED_PARAM_STRUCT
1807 bool "Provide old way to pass kernel parameters"
1810 This was deprecated in 2001 and announced to live on for 5 years.
1811 Some old boot loaders still use this way.
1813 # Compressed boot loader in ROM. Yes, we really want to ask about
1814 # TEXT and BSS so we preserve their values in the config files.
1815 config ZBOOT_ROM_TEXT
1816 hex "Compressed ROM boot loader base address"
1819 The physical address at which the ROM-able zImage is to be
1820 placed in the target. Platforms which normally make use of
1821 ROM-able zImage formats normally set this to a suitable
1822 value in their defconfig file.
1824 If ZBOOT_ROM is not enabled, this has no effect.
1826 config ZBOOT_ROM_BSS
1827 hex "Compressed ROM boot loader BSS address"
1830 The base address of an area of read/write memory in the target
1831 for the ROM-able zImage which must be available while the
1832 decompressor is running. It must be large enough to hold the
1833 entire decompressed kernel plus an additional 128 KiB.
1834 Platforms which normally make use of ROM-able zImage formats
1835 normally set this to a suitable value in their defconfig file.
1837 If ZBOOT_ROM is not enabled, this has no effect.
1840 bool "Compressed boot loader in ROM/flash"
1841 depends on ZBOOT_ROM_TEXT != ZBOOT_ROM_BSS
1842 depends on !ARM_APPENDED_DTB && !XIP_KERNEL && !AUTO_ZRELADDR
1844 Say Y here if you intend to execute your compressed kernel image
1845 (zImage) directly from ROM or flash. If unsure, say N.
1847 config ARM_APPENDED_DTB
1848 bool "Use appended device tree blob to zImage (EXPERIMENTAL)"
1851 With this option, the boot code will look for a device tree binary
1852 (DTB) appended to zImage
1853 (e.g. cat zImage <filename>.dtb > zImage_w_dtb).
1855 This is meant as a backward compatibility convenience for those
1856 systems with a bootloader that can't be upgraded to accommodate
1857 the documented boot protocol using a device tree.
1859 Beware that there is very little in terms of protection against
1860 this option being confused by leftover garbage in memory that might
1861 look like a DTB header after a reboot if no actual DTB is appended
1862 to zImage. Do not leave this option active in a production kernel
1863 if you don't intend to always append a DTB. Proper passing of the
1864 location into r2 of a bootloader provided DTB is always preferable
1867 config ARM_ATAG_DTB_COMPAT
1868 bool "Supplement the appended DTB with traditional ATAG information"
1869 depends on ARM_APPENDED_DTB
1871 Some old bootloaders can't be updated to a DTB capable one, yet
1872 they provide ATAGs with memory configuration, the ramdisk address,
1873 the kernel cmdline string, etc. Such information is dynamically
1874 provided by the bootloader and can't always be stored in a static
1875 DTB. To allow a device tree enabled kernel to be used with such
1876 bootloaders, this option allows zImage to extract the information
1877 from the ATAG list and store it at run time into the appended DTB.
1880 prompt "Kernel command line type" if ARM_ATAG_DTB_COMPAT
1881 default ARM_ATAG_DTB_COMPAT_CMDLINE_FROM_BOOTLOADER
1883 config ARM_ATAG_DTB_COMPAT_CMDLINE_FROM_BOOTLOADER
1884 bool "Use bootloader kernel arguments if available"
1886 Uses the command-line options passed by the boot loader instead of
1887 the device tree bootargs property. If the boot loader doesn't provide
1888 any, the device tree bootargs property will be used.
1890 config ARM_ATAG_DTB_COMPAT_CMDLINE_EXTEND
1891 bool "Extend with bootloader kernel arguments"
1893 The command-line arguments provided by the boot loader will be
1894 appended to the the device tree bootargs property.
1899 string "Default kernel command string"
1902 On some architectures (EBSA110 and CATS), there is currently no way
1903 for the boot loader to pass arguments to the kernel. For these
1904 architectures, you should supply some command-line options at build
1905 time by entering them here. As a minimum, you should specify the
1906 memory size and the root device (e.g., mem=64M root=/dev/nfs).
1909 prompt "Kernel command line type" if CMDLINE != ""
1910 default CMDLINE_FROM_BOOTLOADER
1913 config CMDLINE_FROM_BOOTLOADER
1914 bool "Use bootloader kernel arguments if available"
1916 Uses the command-line options passed by the boot loader. If
1917 the boot loader doesn't provide any, the default kernel command
1918 string provided in CMDLINE will be used.
1920 config CMDLINE_EXTEND
1921 bool "Extend bootloader kernel arguments"
1923 The command-line arguments provided by the boot loader will be
1924 appended to the default kernel command string.
1926 config CMDLINE_FORCE
1927 bool "Always use the default kernel command string"
1929 Always use the default kernel command string, even if the boot
1930 loader passes other arguments to the kernel.
1931 This is useful if you cannot or don't want to change the
1932 command-line options your boot loader passes to the kernel.
1936 bool "Kernel Execute-In-Place from ROM"
1937 depends on !ARM_LPAE && !ARCH_MULTIPLATFORM
1939 Execute-In-Place allows the kernel to run from non-volatile storage
1940 directly addressable by the CPU, such as NOR flash. This saves RAM
1941 space since the text section of the kernel is not loaded from flash
1942 to RAM. Read-write sections, such as the data section and stack,
1943 are still copied to RAM. The XIP kernel is not compressed since
1944 it has to run directly from flash, so it will take more space to
1945 store it. The flash address used to link the kernel object files,
1946 and for storing it, is configuration dependent. Therefore, if you
1947 say Y here, you must know the proper physical address where to
1948 store the kernel image depending on your own flash memory usage.
1950 Also note that the make target becomes "make xipImage" rather than
1951 "make zImage" or "make Image". The final kernel binary to put in
1952 ROM memory will be arch/arm/boot/xipImage.
1956 config XIP_PHYS_ADDR
1957 hex "XIP Kernel Physical Location"
1958 depends on XIP_KERNEL
1959 default "0x00080000"
1961 This is the physical address in your flash memory the kernel will
1962 be linked for and stored to. This address is dependent on your
1965 config XIP_DEFLATED_DATA
1966 bool "Store kernel .data section compressed in ROM"
1967 depends on XIP_KERNEL
1970 Before the kernel is actually executed, its .data section has to be
1971 copied to RAM from ROM. This option allows for storing that data
1972 in compressed form and decompressed to RAM rather than merely being
1973 copied, saving some precious ROM space. A possible drawback is a
1974 slightly longer boot delay.
1977 bool "Kexec system call (EXPERIMENTAL)"
1978 depends on (!SMP || PM_SLEEP_SMP)
1982 kexec is a system call that implements the ability to shutdown your
1983 current kernel, and to start another kernel. It is like a reboot
1984 but it is independent of the system firmware. And like a reboot
1985 you can start any kernel with it, not just Linux.
1987 It is an ongoing process to be certain the hardware in a machine
1988 is properly shutdown, so do not be surprised if this code does not
1989 initially work for you.
1992 bool "Export atags in procfs"
1993 depends on ATAGS && KEXEC
1996 Should the atags used to boot the kernel be exported in an "atags"
1997 file in procfs. Useful with kexec.
2000 bool "Build kdump crash kernel (EXPERIMENTAL)"
2002 Generate crash dump after being started by kexec. This should
2003 be normally only set in special crash dump kernels which are
2004 loaded in the main kernel with kexec-tools into a specially
2005 reserved region and then later executed after a crash by
2006 kdump/kexec. The crash dump kernel must be compiled to a
2007 memory address not used by the main kernel
2009 For more details see Documentation/kdump/kdump.txt
2011 config AUTO_ZRELADDR
2012 bool "Auto calculation of the decompressed kernel image address"
2014 ZRELADDR is the physical address where the decompressed kernel
2015 image will be placed. If AUTO_ZRELADDR is selected, the address
2016 will be determined at run-time by masking the current IP with
2017 0xf8000000. This assumes the zImage being placed in the first 128MB
2018 from start of memory.
2024 bool "UEFI runtime support"
2025 depends on OF && !CPU_BIG_ENDIAN && MMU && AUTO_ZRELADDR && !XIP_KERNEL
2027 select EFI_PARAMS_FROM_FDT
2030 select EFI_RUNTIME_WRAPPERS
2032 This option provides support for runtime services provided
2033 by UEFI firmware (such as non-volatile variables, realtime
2034 clock, and platform reset). A UEFI stub is also provided to
2035 allow the kernel to be booted as an EFI application. This
2036 is only useful for kernels that may run on systems that have
2040 bool "Enable support for SMBIOS (DMI) tables"
2044 This enables SMBIOS/DMI feature for systems.
2046 This option is only useful on systems that have UEFI firmware.
2047 However, even with this option, the resultant kernel should
2048 continue to boot on existing non-UEFI platforms.
2050 NOTE: This does *NOT* enable or encourage the use of DMI quirks,
2051 i.e., the the practice of identifying the platform via DMI to
2052 decide whether certain workarounds for buggy hardware and/or
2053 firmware need to be enabled. This would require the DMI subsystem
2054 to be enabled much earlier than we do on ARM, which is non-trivial.
2058 menu "CPU Power Management"
2060 source "drivers/cpufreq/Kconfig"
2062 source "drivers/cpuidle/Kconfig"
2066 menu "Floating point emulation"
2068 comment "At least one emulation must be selected"
2071 bool "NWFPE math emulation"
2072 depends on (!AEABI || OABI_COMPAT) && !THUMB2_KERNEL
2074 Say Y to include the NWFPE floating point emulator in the kernel.
2075 This is necessary to run most binaries. Linux does not currently
2076 support floating point hardware so you need to say Y here even if
2077 your machine has an FPA or floating point co-processor podule.
2079 You may say N here if you are going to load the Acorn FPEmulator
2080 early in the bootup.
2083 bool "Support extended precision"
2084 depends on FPE_NWFPE
2086 Say Y to include 80-bit support in the kernel floating-point
2087 emulator. Otherwise, only 32 and 64-bit support is compiled in.
2088 Note that gcc does not generate 80-bit operations by default,
2089 so in most cases this option only enlarges the size of the
2090 floating point emulator without any good reason.
2092 You almost surely want to say N here.
2095 bool "FastFPE math emulation (EXPERIMENTAL)"
2096 depends on (!AEABI || OABI_COMPAT) && !CPU_32v3
2098 Say Y here to include the FAST floating point emulator in the kernel.
2099 This is an experimental much faster emulator which now also has full
2100 precision for the mantissa. It does not support any exceptions.
2101 It is very simple, and approximately 3-6 times faster than NWFPE.
2103 It should be sufficient for most programs. It may be not suitable
2104 for scientific calculations, but you have to check this for yourself.
2105 If you do not feel you need a faster FP emulation you should better
2109 bool "VFP-format floating point maths"
2110 depends on CPU_V6 || CPU_V6K || CPU_ARM926T || CPU_V7 || CPU_FEROCEON
2112 Say Y to include VFP support code in the kernel. This is needed
2113 if your hardware includes a VFP unit.
2115 Please see <file:Documentation/arm/VFP/release-notes.txt> for
2116 release notes and additional status information.
2118 Say N if your target does not have VFP hardware.
2126 bool "Advanced SIMD (NEON) Extension support"
2127 depends on VFPv3 && CPU_V7
2129 Say Y to include support code for NEON, the ARMv7 Advanced SIMD
2132 config KERNEL_MODE_NEON
2133 bool "Support for NEON in kernel mode"
2134 depends on NEON && AEABI
2136 Say Y to include support for NEON in kernel mode.
2140 menu "Power management options"
2142 source "kernel/power/Kconfig"
2144 config ARCH_SUSPEND_POSSIBLE
2145 depends on CPU_ARM920T || CPU_ARM926T || CPU_FEROCEON || CPU_SA1100 || \
2146 CPU_V6 || CPU_V6K || CPU_V7 || CPU_V7M || CPU_XSC3 || CPU_XSCALE || CPU_MOHAWK
2149 config ARM_CPU_SUSPEND
2150 def_bool PM_SLEEP || BL_SWITCHER || ARM_PSCI_FW
2151 depends on ARCH_SUSPEND_POSSIBLE
2153 config ARCH_HIBERNATION_POSSIBLE
2156 default y if ARCH_SUSPEND_POSSIBLE
2160 source "drivers/firmware/Kconfig"
2163 source "arch/arm/crypto/Kconfig"
2166 source "arch/arm/kvm/Kconfig"