+++ /dev/null
-#ifdef __KERNEL__
-#ifndef _PPC_PGTABLE_H
-#define _PPC_PGTABLE_H
-
-#include <asm-generic/4level-fixup.h>
-
-
-#ifndef __ASSEMBLY__
-#include <linux/sched.h>
-#include <linux/threads.h>
-#include <asm/processor.h> /* For TASK_SIZE */
-#include <asm/mmu.h>
-#include <asm/page.h>
-#include <asm/io.h> /* For sub-arch specific PPC_PIN_SIZE */
-struct mm_struct;
-
-extern unsigned long va_to_phys(unsigned long address);
-extern pte_t *va_to_pte(unsigned long address);
-extern unsigned long ioremap_bot, ioremap_base;
-#endif /* __ASSEMBLY__ */
-
-/*
- * The PowerPC MMU uses a hash table containing PTEs, together with
- * a set of 16 segment registers (on 32-bit implementations), to define
- * the virtual to physical address mapping.
- *
- * We use the hash table as an extended TLB, i.e. a cache of currently
- * active mappings. We maintain a two-level page table tree, much
- * like that used by the i386, for the sake of the Linux memory
- * management code. Low-level assembler code in hashtable.S
- * (procedure hash_page) is responsible for extracting ptes from the
- * tree and putting them into the hash table when necessary, and
- * updating the accessed and modified bits in the page table tree.
- */
-
-/*
- * The PowerPC MPC8xx uses a TLB with hardware assisted, software tablewalk.
- * We also use the two level tables, but we can put the real bits in them
- * needed for the TLB and tablewalk. These definitions require Mx_CTR.PPM = 0,
- * Mx_CTR.PPCS = 0, and MD_CTR.TWAM = 1. The level 2 descriptor has
- * additional page protection (when Mx_CTR.PPCS = 1) that allows TLB hit
- * based upon user/super access. The TLB does not have accessed nor write
- * protect. We assume that if the TLB get loaded with an entry it is
- * accessed, and overload the changed bit for write protect. We use
- * two bits in the software pte that are supposed to be set to zero in
- * the TLB entry (24 and 25) for these indicators. Although the level 1
- * descriptor contains the guarded and writethrough/copyback bits, we can
- * set these at the page level since they get copied from the Mx_TWC
- * register when the TLB entry is loaded. We will use bit 27 for guard, since
- * that is where it exists in the MD_TWC, and bit 26 for writethrough.
- * These will get masked from the level 2 descriptor at TLB load time, and
- * copied to the MD_TWC before it gets loaded.
- * Large page sizes added. We currently support two sizes, 4K and 8M.
- * This also allows a TLB hander optimization because we can directly
- * load the PMD into MD_TWC. The 8M pages are only used for kernel
- * mapping of well known areas. The PMD (PGD) entries contain control
- * flags in addition to the address, so care must be taken that the
- * software no longer assumes these are only pointers.
- */
-
-/*
- * At present, all PowerPC 400-class processors share a similar TLB
- * architecture. The instruction and data sides share a unified,
- * 64-entry, fully-associative TLB which is maintained totally under
- * software control. In addition, the instruction side has a
- * hardware-managed, 4-entry, fully-associative TLB which serves as a
- * first level to the shared TLB. These two TLBs are known as the UTLB
- * and ITLB, respectively (see "mmu.h" for definitions).
- */
-
-/*
- * The normal case is that PTEs are 32-bits and we have a 1-page
- * 1024-entry pgdir pointing to 1-page 1024-entry PTE pages. -- paulus
- *
- * For any >32-bit physical address platform, we can use the following
- * two level page table layout where the pgdir is 8KB and the MS 13 bits
- * are an index to the second level table. The combined pgdir/pmd first
- * level has 2048 entries and the second level has 512 64-bit PTE entries.
- * -Matt
- */
-/* PMD_SHIFT determines the size of the area mapped by the PTE pages */
-#define PMD_SHIFT (PAGE_SHIFT + PTE_SHIFT)
-#define PMD_SIZE (1UL << PMD_SHIFT)
-#define PMD_MASK (~(PMD_SIZE-1))
-
-/* PGDIR_SHIFT determines what a top-level page table entry can map */
-#define PGDIR_SHIFT PMD_SHIFT
-#define PGDIR_SIZE (1UL << PGDIR_SHIFT)
-#define PGDIR_MASK (~(PGDIR_SIZE-1))
-
-/*
- * entries per page directory level: our page-table tree is two-level, so
- * we don't really have any PMD directory.
- */
-#define PTRS_PER_PTE (1 << PTE_SHIFT)
-#define PTRS_PER_PMD 1
-#define PTRS_PER_PGD (1 << (32 - PGDIR_SHIFT))
-
-#define USER_PTRS_PER_PGD (TASK_SIZE / PGDIR_SIZE)
-#define FIRST_USER_ADDRESS 0
-
-#define USER_PGD_PTRS (PAGE_OFFSET >> PGDIR_SHIFT)
-#define KERNEL_PGD_PTRS (PTRS_PER_PGD-USER_PGD_PTRS)
-
-#define pte_ERROR(e) \
- printk("%s:%d: bad pte "PTE_FMT".\n", __FILE__, __LINE__, pte_val(e))
-#define pmd_ERROR(e) \
- printk("%s:%d: bad pmd %08lx.\n", __FILE__, __LINE__, pmd_val(e))
-#define pgd_ERROR(e) \
- printk("%s:%d: bad pgd %08lx.\n", __FILE__, __LINE__, pgd_val(e))
-
-/*
- * Just any arbitrary offset to the start of the vmalloc VM area: the
- * current 64MB value just means that there will be a 64MB "hole" after the
- * physical memory until the kernel virtual memory starts. That means that
- * any out-of-bounds memory accesses will hopefully be caught.
- * The vmalloc() routines leaves a hole of 4kB between each vmalloced
- * area for the same reason. ;)
- *
- * We no longer map larger than phys RAM with the BATs so we don't have
- * to worry about the VMALLOC_OFFSET causing problems. We do have to worry
- * about clashes between our early calls to ioremap() that start growing down
- * from ioremap_base being run into the VM area allocations (growing upwards
- * from VMALLOC_START). For this reason we have ioremap_bot to check when
- * we actually run into our mappings setup in the early boot with the VM
- * system. This really does become a problem for machines with good amounts
- * of RAM. -- Cort
- */
-#define VMALLOC_OFFSET (0x1000000) /* 16M */
-#ifdef PPC_PIN_SIZE
-#define VMALLOC_START (((_ALIGN((long)high_memory, PPC_PIN_SIZE) + VMALLOC_OFFSET) & ~(VMALLOC_OFFSET-1)))
-#else
-#define VMALLOC_START ((((long)high_memory + VMALLOC_OFFSET) & ~(VMALLOC_OFFSET-1)))
-#endif
-#define VMALLOC_END ioremap_bot
-
-/*
- * Bits in a linux-style PTE. These match the bits in the
- * (hardware-defined) PowerPC PTE as closely as possible.
- */
-
-#if defined(CONFIG_40x)
-
-/* There are several potential gotchas here. The 40x hardware TLBLO
- field looks like this:
-
- 0 1 2 3 4 ... 18 19 20 21 22 23 24 25 26 27 28 29 30 31
- RPN..................... 0 0 EX WR ZSEL....... W I M G
-
- Where possible we make the Linux PTE bits match up with this
-
- - bits 20 and 21 must be cleared, because we use 4k pages (40x can
- support down to 1k pages), this is done in the TLBMiss exception
- handler.
- - We use only zones 0 (for kernel pages) and 1 (for user pages)
- of the 16 available. Bit 24-26 of the TLB are cleared in the TLB
- miss handler. Bit 27 is PAGE_USER, thus selecting the correct
- zone.
- - PRESENT *must* be in the bottom two bits because swap cache
- entries use the top 30 bits. Because 40x doesn't support SMP
- anyway, M is irrelevant so we borrow it for PAGE_PRESENT. Bit 30
- is cleared in the TLB miss handler before the TLB entry is loaded.
- - All other bits of the PTE are loaded into TLBLO without
- modification, leaving us only the bits 20, 21, 24, 25, 26, 30 for
- software PTE bits. We actually use use bits 21, 24, 25, and
- 30 respectively for the software bits: ACCESSED, DIRTY, RW, and
- PRESENT.
-*/
-
-/* Definitions for 40x embedded chips. */
-#define _PAGE_GUARDED 0x001 /* G: page is guarded from prefetch */
-#define _PAGE_FILE 0x001 /* when !present: nonlinear file mapping */
-#define _PAGE_PRESENT 0x002 /* software: PTE contains a translation */
-#define _PAGE_NO_CACHE 0x004 /* I: caching is inhibited */
-#define _PAGE_WRITETHRU 0x008 /* W: caching is write-through */
-#define _PAGE_USER 0x010 /* matches one of the zone permission bits */
-#define _PAGE_RW 0x040 /* software: Writes permitted */
-#define _PAGE_DIRTY 0x080 /* software: dirty page */
-#define _PAGE_HWWRITE 0x100 /* hardware: Dirty & RW, set in exception */
-#define _PAGE_HWEXEC 0x200 /* hardware: EX permission */
-#define _PAGE_ACCESSED 0x400 /* software: R: page referenced */
-
-#define _PMD_PRESENT 0x400 /* PMD points to page of PTEs */
-#define _PMD_BAD 0x802
-#define _PMD_SIZE 0x0e0 /* size field, != 0 for large-page PMD entry */
-#define _PMD_SIZE_4M 0x0c0
-#define _PMD_SIZE_16M 0x0e0
-#define PMD_PAGE_SIZE(pmdval) (1024 << (((pmdval) & _PMD_SIZE) >> 4))
-
-#elif defined(CONFIG_44x)
-/*
- * Definitions for PPC440
- *
- * Because of the 3 word TLB entries to support 36-bit addressing,
- * the attribute are difficult to map in such a fashion that they
- * are easily loaded during exception processing. I decided to
- * organize the entry so the ERPN is the only portion in the
- * upper word of the PTE and the attribute bits below are packed
- * in as sensibly as they can be in the area below a 4KB page size
- * oriented RPN. This at least makes it easy to load the RPN and
- * ERPN fields in the TLB. -Matt
- *
- * Note that these bits preclude future use of a page size
- * less than 4KB.
- *
- *
- * PPC 440 core has following TLB attribute fields;
- *
- * TLB1:
- * 0 1 2 3 4 ... 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31
- * RPN................................. - - - - - - ERPN.......
- *
- * TLB2:
- * 0 1 2 3 4 ... 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31
- * - - - - - - U0 U1 U2 U3 W I M G E - UX UW UR SX SW SR
- *
- * There are some constrains and options, to decide mapping software bits
- * into TLB entry.
- *
- * - PRESENT *must* be in the bottom three bits because swap cache
- * entries use the top 29 bits for TLB2.
- *
- * - FILE *must* be in the bottom three bits because swap cache
- * entries use the top 29 bits for TLB2.
- *
- * - CACHE COHERENT bit (M) has no effect on PPC440 core, because it
- * doesn't support SMP. So we can use this as software bit, like
- * DIRTY.
- *
- * With the PPC 44x Linux implementation, the 0-11th LSBs of the PTE are used
- * for memory protection related functions (see PTE structure in
- * include/asm-ppc/mmu.h). The _PAGE_XXX definitions in this file map to the
- * above bits. Note that the bit values are CPU specific, not architecture
- * specific.
- *
- * The kernel PTE entry holds an arch-dependent swp_entry structure under
- * certain situations. In other words, in such situations some portion of
- * the PTE bits are used as a swp_entry. In the PPC implementation, the
- * 3-24th LSB are shared with swp_entry, however the 0-2nd three LSB still
- * hold protection values. That means the three protection bits are
- * reserved for both PTE and SWAP entry at the most significant three
- * LSBs.
- *
- * There are three protection bits available for SWAP entry:
- * _PAGE_PRESENT
- * _PAGE_FILE
- * _PAGE_HASHPTE (if HW has)
- *
- * So those three bits have to be inside of 0-2nd LSB of PTE.
- *
- */
-
-#define _PAGE_PRESENT 0x00000001 /* S: PTE valid */
-#define _PAGE_RW 0x00000002 /* S: Write permission */
-#define _PAGE_FILE 0x00000004 /* S: nonlinear file mapping */
-#define _PAGE_ACCESSED 0x00000008 /* S: Page referenced */
-#define _PAGE_HWWRITE 0x00000010 /* H: Dirty & RW */
-#define _PAGE_HWEXEC 0x00000020 /* H: Execute permission */
-#define _PAGE_USER 0x00000040 /* S: User page */
-#define _PAGE_ENDIAN 0x00000080 /* H: E bit */
-#define _PAGE_GUARDED 0x00000100 /* H: G bit */
-#define _PAGE_DIRTY 0x00000200 /* S: Page dirty */
-#define _PAGE_NO_CACHE 0x00000400 /* H: I bit */
-#define _PAGE_WRITETHRU 0x00000800 /* H: W bit */
-
-/* TODO: Add large page lowmem mapping support */
-#define _PMD_PRESENT 0
-#define _PMD_PRESENT_MASK (PAGE_MASK)
-#define _PMD_BAD (~PAGE_MASK)
-
-/* ERPN in a PTE never gets cleared, ignore it */
-#define _PTE_NONE_MASK 0xffffffff00000000ULL
-
-#elif defined(CONFIG_8xx)
-/* Definitions for 8xx embedded chips. */
-#define _PAGE_PRESENT 0x0001 /* Page is valid */
-#define _PAGE_FILE 0x0002 /* when !present: nonlinear file mapping */
-#define _PAGE_NO_CACHE 0x0002 /* I: cache inhibit */
-#define _PAGE_SHARED 0x0004 /* No ASID (context) compare */
-
-/* These five software bits must be masked out when the entry is loaded
- * into the TLB.
- */
-#define _PAGE_EXEC 0x0008 /* software: i-cache coherency required */
-#define _PAGE_GUARDED 0x0010 /* software: guarded access */
-#define _PAGE_DIRTY 0x0020 /* software: page changed */
-#define _PAGE_RW 0x0040 /* software: user write access allowed */
-#define _PAGE_ACCESSED 0x0080 /* software: page referenced */
-
-/* Setting any bits in the nibble with the follow two controls will
- * require a TLB exception handler change. It is assumed unused bits
- * are always zero.
- */
-#define _PAGE_HWWRITE 0x0100 /* h/w write enable: never set in Linux PTE */
-#define _PAGE_USER 0x0800 /* One of the PP bits, the other is USER&~RW */
-
-#define _PMD_PRESENT 0x0001
-#define _PMD_BAD 0x0ff0
-#define _PMD_PAGE_MASK 0x000c
-#define _PMD_PAGE_8M 0x000c
-
-#define _PTE_NONE_MASK _PAGE_ACCESSED
-
-#else /* CONFIG_6xx */
-/* Definitions for 60x, 740/750, etc. */
-#define _PAGE_PRESENT 0x001 /* software: pte contains a translation */
-#define _PAGE_HASHPTE 0x002 /* hash_page has made an HPTE for this pte */
-#define _PAGE_FILE 0x004 /* when !present: nonlinear file mapping */
-#define _PAGE_USER 0x004 /* usermode access allowed */
-#define _PAGE_GUARDED 0x008 /* G: prohibit speculative access */
-#define _PAGE_COHERENT 0x010 /* M: enforce memory coherence (SMP systems) */
-#define _PAGE_NO_CACHE 0x020 /* I: cache inhibit */
-#define _PAGE_WRITETHRU 0x040 /* W: cache write-through */
-#define _PAGE_DIRTY 0x080 /* C: page changed */
-#define _PAGE_ACCESSED 0x100 /* R: page referenced */
-#define _PAGE_EXEC 0x200 /* software: i-cache coherency required */
-#define _PAGE_RW 0x400 /* software: user write access allowed */
-
-#define _PTE_NONE_MASK _PAGE_HASHPTE
-
-#define _PMD_PRESENT 0
-#define _PMD_PRESENT_MASK (PAGE_MASK)
-#define _PMD_BAD (~PAGE_MASK)
-#endif
-
-/*
- * Some bits are only used on some cpu families...
- */
-#ifndef _PAGE_HASHPTE
-#define _PAGE_HASHPTE 0
-#endif
-#ifndef _PTE_NONE_MASK
-#define _PTE_NONE_MASK 0
-#endif
-#ifndef _PAGE_SHARED
-#define _PAGE_SHARED 0
-#endif
-#ifndef _PAGE_HWWRITE
-#define _PAGE_HWWRITE 0
-#endif
-#ifndef _PAGE_HWEXEC
-#define _PAGE_HWEXEC 0
-#endif
-#ifndef _PAGE_EXEC
-#define _PAGE_EXEC 0
-#endif
-#ifndef _PMD_PRESENT_MASK
-#define _PMD_PRESENT_MASK _PMD_PRESENT
-#endif
-#ifndef _PMD_SIZE
-#define _PMD_SIZE 0
-#define PMD_PAGE_SIZE(pmd) bad_call_to_PMD_PAGE_SIZE()
-#endif
-
-#define _PAGE_CHG_MASK (PAGE_MASK | _PAGE_ACCESSED | _PAGE_DIRTY)
-
-/*
- * Note: the _PAGE_COHERENT bit automatically gets set in the hardware
- * PTE if CONFIG_SMP is defined (hash_page does this); there is no need
- * to have it in the Linux PTE, and in fact the bit could be reused for
- * another purpose. -- paulus.
- */
-
-#ifdef CONFIG_44x
-#define _PAGE_BASE (_PAGE_PRESENT | _PAGE_ACCESSED | _PAGE_GUARDED)
-#else
-#define _PAGE_BASE (_PAGE_PRESENT | _PAGE_ACCESSED)
-#endif
-#define _PAGE_WRENABLE (_PAGE_RW | _PAGE_DIRTY | _PAGE_HWWRITE)
-#define _PAGE_KERNEL (_PAGE_BASE | _PAGE_SHARED | _PAGE_WRENABLE)
-
-#ifdef CONFIG_PPC_STD_MMU
-/* On standard PPC MMU, no user access implies kernel read/write access,
- * so to write-protect kernel memory we must turn on user access */
-#define _PAGE_KERNEL_RO (_PAGE_BASE | _PAGE_SHARED | _PAGE_USER)
-#else
-#define _PAGE_KERNEL_RO (_PAGE_BASE | _PAGE_SHARED)
-#endif
-
-#define _PAGE_IO (_PAGE_KERNEL | _PAGE_NO_CACHE | _PAGE_GUARDED)
-#define _PAGE_RAM (_PAGE_KERNEL | _PAGE_HWEXEC)
-
-#if defined(CONFIG_KGDB) || defined(CONFIG_XMON) || defined(CONFIG_BDI_SWITCH)
-/* We want the debuggers to be able to set breakpoints anywhere, so
- * don't write protect the kernel text */
-#define _PAGE_RAM_TEXT _PAGE_RAM
-#else
-#define _PAGE_RAM_TEXT (_PAGE_KERNEL_RO | _PAGE_HWEXEC)
-#endif
-
-#define PAGE_NONE __pgprot(_PAGE_BASE)
-#define PAGE_READONLY __pgprot(_PAGE_BASE | _PAGE_USER)
-#define PAGE_READONLY_X __pgprot(_PAGE_BASE | _PAGE_USER | _PAGE_EXEC)
-#define PAGE_SHARED __pgprot(_PAGE_BASE | _PAGE_USER | _PAGE_RW)
-#define PAGE_SHARED_X __pgprot(_PAGE_BASE | _PAGE_USER | _PAGE_RW | _PAGE_EXEC)
-#define PAGE_COPY __pgprot(_PAGE_BASE | _PAGE_USER)
-#define PAGE_COPY_X __pgprot(_PAGE_BASE | _PAGE_USER | _PAGE_EXEC)
-
-#define PAGE_KERNEL __pgprot(_PAGE_RAM)
-#define PAGE_KERNEL_NOCACHE __pgprot(_PAGE_IO)
-
-/*
- * The PowerPC can only do execute protection on a segment (256MB) basis,
- * not on a page basis. So we consider execute permission the same as read.
- * Also, write permissions imply read permissions.
- * This is the closest we can get..
- */
-#define __P000 PAGE_NONE
-#define __P001 PAGE_READONLY_X
-#define __P010 PAGE_COPY
-#define __P011 PAGE_COPY_X
-#define __P100 PAGE_READONLY
-#define __P101 PAGE_READONLY_X
-#define __P110 PAGE_COPY
-#define __P111 PAGE_COPY_X
-
-#define __S000 PAGE_NONE
-#define __S001 PAGE_READONLY_X
-#define __S010 PAGE_SHARED
-#define __S011 PAGE_SHARED_X
-#define __S100 PAGE_READONLY
-#define __S101 PAGE_READONLY_X
-#define __S110 PAGE_SHARED
-#define __S111 PAGE_SHARED_X
-
-#ifndef __ASSEMBLY__
-/* Make sure we get a link error if PMD_PAGE_SIZE is ever called on a
- * kernel without large page PMD support */
-extern unsigned long bad_call_to_PMD_PAGE_SIZE(void);
-
-/*
- * Conversions between PTE values and page frame numbers.
- */
-
-/* in some case we want to additionaly adjust where the pfn is in the pte to
- * allow room for more flags */
-#define PFN_SHIFT_OFFSET (PAGE_SHIFT)
-
-#define pte_pfn(x) (pte_val(x) >> PFN_SHIFT_OFFSET)
-#define pte_page(x) pfn_to_page(pte_pfn(x))
-
-#define pfn_pte(pfn, prot) __pte(((pte_basic_t)(pfn) << PFN_SHIFT_OFFSET) |\
- pgprot_val(prot))
-#define mk_pte(page, prot) pfn_pte(page_to_pfn(page), prot)
-
-/*
- * ZERO_PAGE is a global shared page that is always zero: used
- * for zero-mapped memory areas etc..
- */
-extern unsigned long empty_zero_page[1024];
-#define ZERO_PAGE(vaddr) (virt_to_page(empty_zero_page))
-
-#endif /* __ASSEMBLY__ */
-
-#define pte_none(pte) ((pte_val(pte) & ~_PTE_NONE_MASK) == 0)
-#define pte_present(pte) (pte_val(pte) & _PAGE_PRESENT)
-#define pte_clear(mm,addr,ptep) do { set_pte_at((mm), (addr), (ptep), __pte(0)); } while (0)
-
-#define pmd_none(pmd) (!pmd_val(pmd))
-#define pmd_bad(pmd) (pmd_val(pmd) & _PMD_BAD)
-#define pmd_present(pmd) (pmd_val(pmd) & _PMD_PRESENT_MASK)
-#define pmd_clear(pmdp) do { pmd_val(*(pmdp)) = 0; } while (0)
-
-#ifndef __ASSEMBLY__
-/*
- * The "pgd_xxx()" functions here are trivial for a folded two-level
- * setup: the pgd is never bad, and a pmd always exists (as it's folded
- * into the pgd entry)
- */
-static inline int pgd_none(pgd_t pgd) { return 0; }
-static inline int pgd_bad(pgd_t pgd) { return 0; }
-static inline int pgd_present(pgd_t pgd) { return 1; }
-#define pgd_clear(xp) do { } while (0)
-
-#define pgd_page_vaddr(pgd) \
- ((unsigned long) __va(pgd_val(pgd) & PAGE_MASK))
-
-/*
- * The following only work if pte_present() is true.
- * Undefined behaviour if not..
- */
-static inline int pte_write(pte_t pte) { return pte_val(pte) & _PAGE_RW; }
-static inline int pte_dirty(pte_t pte) { return pte_val(pte) & _PAGE_DIRTY; }
-static inline int pte_young(pte_t pte) { return pte_val(pte) & _PAGE_ACCESSED; }
-static inline int pte_file(pte_t pte) { return pte_val(pte) & _PAGE_FILE; }
-static inline int pte_special(pte_t pte) { return 0; }
-
-static inline void pte_uncache(pte_t pte) { pte_val(pte) |= _PAGE_NO_CACHE; }
-static inline void pte_cache(pte_t pte) { pte_val(pte) &= ~_PAGE_NO_CACHE; }
-
-static inline pte_t pte_wrprotect(pte_t pte) {
- pte_val(pte) &= ~(_PAGE_RW | _PAGE_HWWRITE); return pte; }
-static inline pte_t pte_mkclean(pte_t pte) {
- pte_val(pte) &= ~(_PAGE_DIRTY | _PAGE_HWWRITE); return pte; }
-static inline pte_t pte_mkold(pte_t pte) {
- pte_val(pte) &= ~_PAGE_ACCESSED; return pte; }
-
-static inline pte_t pte_mkwrite(pte_t pte) {
- pte_val(pte) |= _PAGE_RW; return pte; }
-static inline pte_t pte_mkdirty(pte_t pte) {
- pte_val(pte) |= _PAGE_DIRTY; return pte; }
-static inline pte_t pte_mkyoung(pte_t pte) {
- pte_val(pte) |= _PAGE_ACCESSED; return pte; }
-static inline pte_t pte_mkspecial(pte_t pte) {
- return pte; }
-
-static inline pte_t pte_modify(pte_t pte, pgprot_t newprot)
-{
- pte_val(pte) = (pte_val(pte) & _PAGE_CHG_MASK) | pgprot_val(newprot);
- return pte;
-}
-
-/*
- * When flushing the tlb entry for a page, we also need to flush the hash
- * table entry. flush_hash_pages is assembler (for speed) in hashtable.S.
- */
-extern int flush_hash_pages(unsigned context, unsigned long va,
- unsigned long pmdval, int count);
-
-/* Add an HPTE to the hash table */
-extern void add_hash_page(unsigned context, unsigned long va,
- unsigned long pmdval);
-
-/*
- * Atomic PTE updates.
- *
- * pte_update clears and sets bit atomically, and returns
- * the old pte value. In the 64-bit PTE case we lock around the
- * low PTE word since we expect ALL flag bits to be there
- */
-#ifndef CONFIG_PTE_64BIT
-static inline unsigned long pte_update(pte_t *p, unsigned long clr,
- unsigned long set)
-{
- unsigned long old, tmp;
-
- __asm__ __volatile__("\
-1: lwarx %0,0,%3\n\
- andc %1,%0,%4\n\
- or %1,%1,%5\n"
- PPC405_ERR77(0,%3)
-" stwcx. %1,0,%3\n\
- bne- 1b"
- : "=&r" (old), "=&r" (tmp), "=m" (*p)
- : "r" (p), "r" (clr), "r" (set), "m" (*p)
- : "cc" );
- return old;
-}
-#else
-static inline unsigned long long pte_update(pte_t *p, unsigned long clr,
- unsigned long set)
-{
- unsigned long long old;
- unsigned long tmp;
-
- __asm__ __volatile__("\
-1: lwarx %L0,0,%4\n\
- lwzx %0,0,%3\n\
- andc %1,%L0,%5\n\
- or %1,%1,%6\n"
- PPC405_ERR77(0,%3)
-" stwcx. %1,0,%4\n\
- bne- 1b"
- : "=&r" (old), "=&r" (tmp), "=m" (*p)
- : "r" (p), "r" ((unsigned long)(p) + 4), "r" (clr), "r" (set), "m" (*p)
- : "cc" );
- return old;
-}
-#endif
-
-/*
- * set_pte stores a linux PTE into the linux page table.
- * On machines which use an MMU hash table we avoid changing the
- * _PAGE_HASHPTE bit.
- */
-static inline void set_pte_at(struct mm_struct *mm, unsigned long addr,
- pte_t *ptep, pte_t pte)
-{
-#if _PAGE_HASHPTE != 0
- pte_update(ptep, ~_PAGE_HASHPTE, pte_val(pte) & ~_PAGE_HASHPTE);
-#else
- *ptep = pte;
-#endif
-}
-
-/*
- * 2.6 calles this without flushing the TLB entry, this is wrong
- * for our hash-based implementation, we fix that up here
- */
-#define __HAVE_ARCH_PTEP_TEST_AND_CLEAR_YOUNG
-static inline int __ptep_test_and_clear_young(unsigned int context, unsigned long addr, pte_t *ptep)
-{
- unsigned long old;
- old = pte_update(ptep, _PAGE_ACCESSED, 0);
-#if _PAGE_HASHPTE != 0
- if (old & _PAGE_HASHPTE) {
- unsigned long ptephys = __pa(ptep) & PAGE_MASK;
- flush_hash_pages(context, addr, ptephys, 1);
- }
-#endif
- return (old & _PAGE_ACCESSED) != 0;
-}
-#define ptep_test_and_clear_young(__vma, __addr, __ptep) \
- __ptep_test_and_clear_young((__vma)->vm_mm->context.id, __addr, __ptep)
-
-#define __HAVE_ARCH_PTEP_GET_AND_CLEAR
-static inline pte_t ptep_get_and_clear(struct mm_struct *mm, unsigned long addr,
- pte_t *ptep)
-{
- return __pte(pte_update(ptep, ~_PAGE_HASHPTE, 0));
-}
-
-#define __HAVE_ARCH_PTEP_SET_WRPROTECT
-static inline void ptep_set_wrprotect(struct mm_struct *mm, unsigned long addr,
- pte_t *ptep)
-{
- pte_update(ptep, (_PAGE_RW | _PAGE_HWWRITE), 0);
-}
-
-#define __HAVE_ARCH_PTEP_SET_ACCESS_FLAGS
-static inline void __ptep_set_access_flags(pte_t *ptep, pte_t entry, int dirty)
-{
- unsigned long bits = pte_val(entry) &
- (_PAGE_DIRTY | _PAGE_ACCESSED | _PAGE_RW);
- pte_update(ptep, 0, bits);
-}
-
-#define ptep_set_access_flags(__vma, __address, __ptep, __entry, __dirty) \
-({ \
- int __changed = !pte_same(*(__ptep), __entry); \
- if (__changed) { \
- __ptep_set_access_flags(__ptep, __entry, __dirty); \
- flush_tlb_page_nohash(__vma, __address); \
- } \
- __changed; \
-})
-
-/*
- * Macro to mark a page protection value as "uncacheable".
- */
-#define pgprot_noncached(prot) (__pgprot(pgprot_val(prot) | _PAGE_NO_CACHE | _PAGE_GUARDED))
-
-struct file;
-extern pgprot_t phys_mem_access_prot(struct file *file, unsigned long pfn,
- unsigned long size, pgprot_t vma_prot);
-#define __HAVE_PHYS_MEM_ACCESS_PROT
-
-#define __HAVE_ARCH_PTE_SAME
-#define pte_same(A,B) (((pte_val(A) ^ pte_val(B)) & ~_PAGE_HASHPTE) == 0)
-
-/*
- * Note that on Book E processors, the pmd contains the kernel virtual
- * (lowmem) address of the pte page. The physical address is less useful
- * because everything runs with translation enabled (even the TLB miss
- * handler). On everything else the pmd contains the physical address
- * of the pte page. -- paulus
- */
-#ifndef CONFIG_BOOKE
-#define pmd_page_vaddr(pmd) \
- ((unsigned long) __va(pmd_val(pmd) & PAGE_MASK))
-#define pmd_page(pmd) \
- (mem_map + (pmd_val(pmd) >> PAGE_SHIFT))
-#else
-#define pmd_page_vaddr(pmd) \
- ((unsigned long) (pmd_val(pmd) & PAGE_MASK))
-#define pmd_page(pmd) \
- (mem_map + (__pa(pmd_val(pmd)) >> PAGE_SHIFT))
-#endif
-
-/* to find an entry in a kernel page-table-directory */
-#define pgd_offset_k(address) pgd_offset(&init_mm, address)
-
-/* to find an entry in a page-table-directory */
-#define pgd_index(address) ((address) >> PGDIR_SHIFT)
-#define pgd_offset(mm, address) ((mm)->pgd + pgd_index(address))
-
-/* Find an entry in the second-level page table.. */
-static inline pmd_t * pmd_offset(pgd_t * dir, unsigned long address)
-{
- return (pmd_t *) dir;
-}
-
-/* Find an entry in the third-level page table.. */
-#define pte_index(address) \
- (((address) >> PAGE_SHIFT) & (PTRS_PER_PTE - 1))
-#define pte_offset_kernel(dir, addr) \
- ((pte_t *) pmd_page_vaddr(*(dir)) + pte_index(addr))
-#define pte_offset_map(dir, addr) \
- ((pte_t *) kmap_atomic(pmd_page(*(dir)), KM_PTE0) + pte_index(addr))
-#define pte_offset_map_nested(dir, addr) \
- ((pte_t *) kmap_atomic(pmd_page(*(dir)), KM_PTE1) + pte_index(addr))
-
-#define pte_unmap(pte) kunmap_atomic(pte, KM_PTE0)
-#define pte_unmap_nested(pte) kunmap_atomic(pte, KM_PTE1)
-
-extern pgd_t swapper_pg_dir[PTRS_PER_PGD];
-
-extern void paging_init(void);
-
-/*
- * Encode and decode a swap entry.
- * Note that the bits we use in a PTE for representing a swap entry
- * must not include the _PAGE_PRESENT bit, the _PAGE_FILE bit, or the
- *_PAGE_HASHPTE bit (if used). -- paulus
- */
-#define __swp_type(entry) ((entry).val & 0x1f)
-#define __swp_offset(entry) ((entry).val >> 5)
-#define __swp_entry(type, offset) ((swp_entry_t) { (type) | ((offset) << 5) })
-#define __pte_to_swp_entry(pte) ((swp_entry_t) { pte_val(pte) >> 3 })
-#define __swp_entry_to_pte(x) ((pte_t) { (x).val << 3 })
-
-/* Encode and decode a nonlinear file mapping entry */
-#define PTE_FILE_MAX_BITS 29
-#define pte_to_pgoff(pte) (pte_val(pte) >> 3)
-#define pgoff_to_pte(off) ((pte_t) { ((off) << 3) | _PAGE_FILE })
-
-/* Values for nocacheflag and cmode */
-/* These are not used by the APUS kernel_map, but prevents
- compilation errors. */
-#define KERNELMAP_FULL_CACHING 0
-#define KERNELMAP_NOCACHE_SER 1
-#define KERNELMAP_NOCACHE_NONSER 2
-#define KERNELMAP_NO_COPYBACK 3
-
-/*
- * Map some physical address range into the kernel address space.
- */
-extern unsigned long kernel_map(unsigned long paddr, unsigned long size,
- int nocacheflag, unsigned long *memavailp );
-
-/*
- * Set cache mode of (kernel space) address range.
- */
-extern void kernel_set_cachemode (unsigned long address, unsigned long size,
- unsigned int cmode);
-
-/* Needs to be defined here and not in linux/mm.h, as it is arch dependent */
-#define kern_addr_valid(addr) (1)
-
-#ifdef CONFIG_PHYS_64BIT
-extern int remap_pfn_range(struct vm_area_struct *vma, unsigned long from,
- unsigned long paddr, unsigned long size, pgprot_t prot);
-
-static inline int io_remap_pfn_range(struct vm_area_struct *vma,
- unsigned long vaddr,
- unsigned long pfn,
- unsigned long size,
- pgprot_t prot)
-{
- phys_addr_t paddr64 = fixup_bigphys_addr(pfn << PAGE_SHIFT, size);
- return remap_pfn_range(vma, vaddr, paddr64 >> PAGE_SHIFT, size, prot);
-}
-#else
-#define io_remap_pfn_range(vma, vaddr, pfn, size, prot) \
- remap_pfn_range(vma, vaddr, pfn, size, prot)
-#endif
-
-/*
- * No page table caches to initialise
- */
-#define pgtable_cache_init() do { } while (0)
-
-extern int get_pteptr(struct mm_struct *mm, unsigned long addr, pte_t **ptep,
- pmd_t **pmdp);
-
-#include <asm-generic/pgtable.h>
-
-#endif /* !__ASSEMBLY__ */
-
-#endif /* _PPC_PGTABLE_H */
-#endif /* __KERNEL__ */
git.samba.org / sfrench / cifs-2.6.git / blobdiff