-config MTD_NAND_ECC
- tristate
-
-config MTD_NAND_ECC_SMC
- bool "NAND ECC Smart Media byte order"
- depends on MTD_NAND_ECC
- default n
- help
- Software ECC according to the Smart Media Specification.
- The original Linux implementation had byte 0 and 1 swapped.
-
-
-menuconfig MTD_NAND
- tristate "NAND Device Support"
- depends on MTD
- select MTD_NAND_ECC
- help
- This enables support for accessing all type of NAND flash
- devices. For further information see
- <http://www.linux-mtd.infradead.org/doc/nand.html>.
-
-if MTD_NAND
-
-config MTD_NAND_BCH
- tristate
- select BCH
- depends on MTD_NAND_ECC_BCH
- default MTD_NAND
-
-config MTD_NAND_ECC_BCH
- bool "Support software BCH ECC"
- default n
- help
- This enables support for software BCH error correction. Binary BCH
- codes are more powerful and cpu intensive than traditional Hamming
- ECC codes. They are used with NAND devices requiring more than 1 bit
- of error correction.
-
-config MTD_SM_COMMON
- tristate
- default n
-
-config MTD_NAND_DENALI
- tristate
-
-config MTD_NAND_DENALI_PCI
- tristate "Support Denali NAND controller on Intel Moorestown"
- select MTD_NAND_DENALI
- depends on HAS_DMA && PCI
- help
- Enable the driver for NAND flash on Intel Moorestown, using the
- Denali NAND controller core.
-
-config MTD_NAND_DENALI_DT
- tristate "Support Denali NAND controller as a DT device"
- select MTD_NAND_DENALI
- depends on HAS_DMA && HAVE_CLK && OF
- help
- Enable the driver for NAND flash on platforms using a Denali NAND
- controller as a DT device.
-
-config MTD_NAND_GPIO
- tristate "GPIO assisted NAND Flash driver"
- depends on GPIOLIB || COMPILE_TEST
- depends on HAS_IOMEM
- help
- This enables a NAND flash driver where control signals are
- connected to GPIO pins, and commands and data are communicated
- via a memory mapped interface.
-
-config MTD_NAND_AMS_DELTA
- tristate "NAND Flash device on Amstrad E3"
- depends on MACH_AMS_DELTA
- default y
- help
- Support for NAND flash on Amstrad E3 (Delta).
-
-config MTD_NAND_OMAP2
- tristate "NAND Flash device on OMAP2, OMAP3, OMAP4 and Keystone"
- depends on (ARCH_OMAP2PLUS || ARCH_KEYSTONE)
- help
- Support for NAND flash on Texas Instruments OMAP2, OMAP3, OMAP4
- and Keystone platforms.
-
-config MTD_NAND_OMAP_BCH
- depends on MTD_NAND_OMAP2
- bool "Support hardware based BCH error correction"
- default n
- select BCH
- help
- This config enables the ELM hardware engine, which can be used to
- locate and correct errors when using BCH ECC scheme. This offloads
- the cpu from doing ECC error searching and correction. However some
- legacy OMAP families like OMAP2xxx, OMAP3xxx do not have ELM engine
- so this is optional for them.
-
-config MTD_NAND_OMAP_BCH_BUILD
- def_tristate MTD_NAND_OMAP2 && MTD_NAND_OMAP_BCH
-
-config MTD_NAND_RICOH
- tristate "Ricoh xD card reader"
- default n
- depends on PCI
- select MTD_SM_COMMON
- help
- Enable support for Ricoh R5C852 xD card reader
- You also need to enable ether
- NAND SSFDC (SmartMedia) read only translation layer' or new
- expermental, readwrite
- 'SmartMedia/xD new translation layer'
-
-config MTD_NAND_AU1550
- tristate "Au1550/1200 NAND support"
- depends on MIPS_ALCHEMY
- help
- This enables the driver for the NAND flash controller on the
- AMD/Alchemy 1550 SOC.
-
-config MTD_NAND_BF5XX
- tristate "Blackfin on-chip NAND Flash Controller driver"
- depends on BF54x || BF52x
- help
- This enables the Blackfin on-chip NAND flash controller
-
- No board specific support is done by this driver, each board
- must advertise a platform_device for the driver to attach.
-
- This driver can also be built as a module. If so, the module
- will be called bf5xx-nand.
-
-config MTD_NAND_BF5XX_HWECC
- bool "BF5XX NAND Hardware ECC"
- default y
- depends on MTD_NAND_BF5XX
- help
- Enable the use of the BF5XX's internal ECC generator when
- using NAND.
-
-config MTD_NAND_BF5XX_BOOTROM_ECC
- bool "Use Blackfin BootROM ECC Layout"
- default n
- depends on MTD_NAND_BF5XX_HWECC
- help
- If you wish to modify NAND pages and allow the Blackfin on-chip
- BootROM to boot from them, say Y here. This is only necessary
- if you are booting U-Boot out of NAND and you wish to update
- U-Boot from Linux' userspace. Otherwise, you should say N here.
-
- If unsure, say N.
-
-config MTD_NAND_S3C2410
- tristate "NAND Flash support for Samsung S3C SoCs"
- depends on ARCH_S3C24XX || ARCH_S3C64XX
- help
- This enables the NAND flash controller on the S3C24xx and S3C64xx
- SoCs
-
- No board specific support is done by this driver, each board
- must advertise a platform_device for the driver to attach.
-
-config MTD_NAND_S3C2410_DEBUG
- bool "Samsung S3C NAND driver debug"
- depends on MTD_NAND_S3C2410
- help
- Enable debugging of the S3C NAND driver
-
-config MTD_NAND_NDFC
- tristate "NDFC NanD Flash Controller"
- depends on 4xx
- select MTD_NAND_ECC_SMC
- help
- NDFC Nand Flash Controllers are integrated in IBM/AMCC's 4xx SoCs
-
-config MTD_NAND_S3C2410_CLKSTOP
- bool "Samsung S3C NAND IDLE clock stop"
- depends on MTD_NAND_S3C2410
- default n
- help
- Stop the clock to the NAND controller when there is no chip
- selected to save power. This will mean there is a small delay
- when the is NAND chip selected or released, but will save
- approximately 5mA of power when there is nothing happening.
-
-config MTD_NAND_TANGO
- tristate "NAND Flash support for Tango chips"
- depends on ARCH_TANGO || COMPILE_TEST
- depends on HAS_DMA
- help
- Enables the NAND Flash controller on Tango chips.
-
-config MTD_NAND_DISKONCHIP
- tristate "DiskOnChip 2000, Millennium and Millennium Plus (NAND reimplementation)"
- depends on HAS_IOMEM
- select REED_SOLOMON
- select REED_SOLOMON_DEC16
- help
- This is a reimplementation of M-Systems DiskOnChip 2000,
- Millennium and Millennium Plus as a standard NAND device driver,
- as opposed to the earlier self-contained MTD device drivers.
- This should enable, among other things, proper JFFS2 operation on
- these devices.
-
-config MTD_NAND_DISKONCHIP_PROBE_ADVANCED
- bool "Advanced detection options for DiskOnChip"
- depends on MTD_NAND_DISKONCHIP
- help
- This option allows you to specify nonstandard address at which to
- probe for a DiskOnChip, or to change the detection options. You
- are unlikely to need any of this unless you are using LinuxBIOS.
- Say 'N'.
-
-config MTD_NAND_DISKONCHIP_PROBE_ADDRESS
- hex "Physical address of DiskOnChip" if MTD_NAND_DISKONCHIP_PROBE_ADVANCED
- depends on MTD_NAND_DISKONCHIP
- default "0"
- ---help---
- By default, the probe for DiskOnChip devices will look for a
- DiskOnChip at every multiple of 0x2000 between 0xC8000 and 0xEE000.
- This option allows you to specify a single address at which to probe
- for the device, which is useful if you have other devices in that
- range which get upset when they are probed.
-
- (Note that on PowerPC, the normal probe will only check at
- 0xE4000000.)
-
- Normally, you should leave this set to zero, to allow the probe at
- the normal addresses.
-
-config MTD_NAND_DISKONCHIP_PROBE_HIGH
- bool "Probe high addresses"
- depends on MTD_NAND_DISKONCHIP_PROBE_ADVANCED
- help
- By default, the probe for DiskOnChip devices will look for a
- DiskOnChip at every multiple of 0x2000 between 0xC8000 and 0xEE000.
- This option changes to make it probe between 0xFFFC8000 and
- 0xFFFEE000. Unless you are using LinuxBIOS, this is unlikely to be
- useful to you. Say 'N'.
-
-config MTD_NAND_DISKONCHIP_BBTWRITE
- bool "Allow BBT writes on DiskOnChip Millennium and 2000TSOP"
- depends on MTD_NAND_DISKONCHIP
- help
- On DiskOnChip devices shipped with the INFTL filesystem (Millennium
- and 2000 TSOP/Alon), Linux reserves some space at the end of the
- device for the Bad Block Table (BBT). If you have existing INFTL
- data on your device (created by non-Linux tools such as M-Systems'
- DOS drivers), your data might overlap the area Linux wants to use for
- the BBT. If this is a concern for you, leave this option disabled and
- Linux will not write BBT data into this area.
- The downside of leaving this option disabled is that if bad blocks
- are detected by Linux, they will not be recorded in the BBT, which
- could cause future problems.
- Once you enable this option, new filesystems (INFTL or others, created
- in Linux or other operating systems) will not use the reserved area.
- The only reason not to enable this option is to prevent damage to
- preexisting filesystems.
- Even if you leave this disabled, you can enable BBT writes at module
- load time (assuming you build diskonchip as a module) with the module
- parameter "inftl_bbt_write=1".
-
-config MTD_NAND_DOCG4
- tristate "Support for DiskOnChip G4"
- depends on HAS_IOMEM
- select BCH
- select BITREVERSE
- help
- Support for diskonchip G4 nand flash, found in various smartphones and
- PDAs, among them the Palm Treo680, HTC Prophet and Wizard, Toshiba
- Portege G900, Asus P526, and O2 XDA Zinc.
-
- With this driver you will be able to use UBI and create a ubifs on the
- device, so you may wish to consider enabling UBI and UBIFS as well.
-
- These devices ship with the Mys/Sandisk SAFTL formatting, for which
- there is currently no mtd parser, so you may want to use command line
- partitioning to segregate write-protected blocks. On the Treo680, the
- first five erase blocks (256KiB each) are write-protected, followed
- by the block containing the saftl partition table. This is probably
- typical.
-
-config MTD_NAND_SHARPSL
- tristate "Support for NAND Flash on Sharp SL Series (C7xx + others)"
- depends on ARCH_PXA
-
-config MTD_NAND_CAFE
- tristate "NAND support for OLPC CAFÉ chip"
- depends on PCI
- select REED_SOLOMON
- select REED_SOLOMON_DEC16
- help
- Use NAND flash attached to the CAFÉ chip designed for the OLPC
- laptop.
-
-config MTD_NAND_CS553X
- tristate "NAND support for CS5535/CS5536 (AMD Geode companion chip)"
- depends on X86_32
- depends on !UML && HAS_IOMEM
- help
- The CS553x companion chips for the AMD Geode processor
- include NAND flash controllers with built-in hardware ECC
- capabilities; enabling this option will allow you to use
- these. The driver will check the MSRs to verify that the
- controller is enabled for NAND, and currently requires that
- the controller be in MMIO mode.
-
- If you say "m", the module will be called cs553x_nand.
-
-config MTD_NAND_ATMEL
- tristate "Support for NAND Flash / SmartMedia on AT91"
- depends on ARCH_AT91
- select MFD_ATMEL_SMC
- help
- Enables support for NAND Flash / Smart Media Card interface
- on Atmel AT91 processors.
-
-config MTD_NAND_PXA3xx
- tristate "NAND support on PXA3xx and Armada 370/XP"
- depends on !MTD_NAND_MARVELL
- depends on PXA3xx || ARCH_MMP || PLAT_ORION || ARCH_MVEBU
- help
-
- This enables the driver for the NAND flash device found on
- PXA3xx processors (NFCv1) and also on 32-bit Armada
- platforms (XP, 370, 375, 38x, 39x) and 64-bit Armada
- platforms (7K, 8K) (NFCv2).
-
-config MTD_NAND_MARVELL
- tristate "NAND controller support on Marvell boards"
- depends on PXA3xx || ARCH_MMP || PLAT_ORION || ARCH_MVEBU || \
- COMPILE_TEST
- depends on HAS_IOMEM
- help
- This enables the NAND flash controller driver for Marvell boards,
- including:
- - PXA3xx processors (NFCv1)
- - 32-bit Armada platforms (XP, 37x, 38x, 39x) (NFCv2)
- - 64-bit Aramda platforms (7k, 8k) (NFCv2)
-
-config MTD_NAND_SLC_LPC32XX
- tristate "NXP LPC32xx SLC Controller"
- depends on ARCH_LPC32XX
- help
- Enables support for NXP's LPC32XX SLC (i.e. for Single Level Cell
- chips) NAND controller. This is the default for the PHYTEC 3250
- reference board which contains a NAND256R3A2CZA6 chip.
-
- Please check the actual NAND chip connected and its support
- by the SLC NAND controller.
-
-config MTD_NAND_MLC_LPC32XX
- tristate "NXP LPC32xx MLC Controller"
- depends on ARCH_LPC32XX
- help
- Uses the LPC32XX MLC (i.e. for Multi Level Cell chips) NAND
- controller. This is the default for the WORK92105 controller
- board.
-
- Please check the actual NAND chip connected and its support
- by the MLC NAND controller.
-
-config MTD_NAND_CM_X270
- tristate "Support for NAND Flash on CM-X270 modules"
- depends on MACH_ARMCORE
-
-config MTD_NAND_PASEMI
- tristate "NAND support for PA Semi PWRficient"
- depends on PPC_PASEMI
- help
- Enables support for NAND Flash interface on PA Semi PWRficient
- based boards
-
-config MTD_NAND_TMIO
- tristate "NAND Flash device on Toshiba Mobile IO Controller"
- depends on MFD_TMIO
- help
- Support for NAND flash connected to a Toshiba Mobile IO
- Controller in some PDAs, including the Sharp SL6000x.
-
-config MTD_NAND_NANDSIM
- tristate "Support for NAND Flash Simulator"
- help
- The simulator may simulate various NAND flash chips for the
- MTD nand layer.
-
-config MTD_NAND_GPMI_NAND
- tristate "GPMI NAND Flash Controller driver"
- depends on MTD_NAND && MXS_DMA
- help
- Enables NAND Flash support for IMX23, IMX28 or IMX6.
- The GPMI controller is very powerful, with the help of BCH
- module, it can do the hardware ECC. The GPMI supports several
- NAND flashs at the same time.
-
-config MTD_NAND_BRCMNAND
- tristate "Broadcom STB NAND controller"
- depends on ARM || ARM64 || MIPS
- help
- Enables the Broadcom NAND controller driver. The controller was
- originally designed for Set-Top Box but is used on various BCM7xxx,
- BCM3xxx, BCM63xxx, iProc/Cygnus and more.
-
-config MTD_NAND_BCM47XXNFLASH
- tristate "Support for NAND flash on BCM4706 BCMA bus"
- depends on BCMA_NFLASH
- help
- BCMA bus can have various flash memories attached, they are
- registered by bcma as platform devices. This enables driver for
- NAND flash memories. For now only BCM4706 is supported.
-
-config MTD_NAND_PLATFORM
- tristate "Support for generic platform NAND driver"
- depends on HAS_IOMEM
- help
- This implements a generic NAND driver for on-SOC platform
- devices. You will need to provide platform-specific functions
- via platform_data.
-
-config MTD_NAND_ORION
- tristate "NAND Flash support for Marvell Orion SoC"
- depends on PLAT_ORION
- help
- This enables the NAND flash controller on Orion machines.
-
- No board specific support is done by this driver, each board
- must advertise a platform_device for the driver to attach.
-
-config MTD_NAND_OXNAS
- tristate "NAND Flash support for Oxford Semiconductor SoC"
- depends on ARCH_OXNAS || COMPILE_TEST
- depends on HAS_IOMEM
- help
- This enables the NAND flash controller on Oxford Semiconductor SoCs.
-
-config MTD_NAND_FSL_ELBC
- tristate "NAND support for Freescale eLBC controllers"
- depends on FSL_SOC
- select FSL_LBC
- help
- Various Freescale chips, including the 8313, include a NAND Flash
- Controller Module with built-in hardware ECC capabilities.
- Enabling this option will enable you to use this to control
- external NAND devices.
-
-config MTD_NAND_FSL_IFC
- tristate "NAND support for Freescale IFC controller"
- depends on FSL_SOC || ARCH_LAYERSCAPE || SOC_LS1021A
- select FSL_IFC
- select MEMORY
- help
- Various Freescale chips e.g P1010, include a NAND Flash machine
- with built-in hardware ECC capabilities.
- Enabling this option will enable you to use this to control
- external NAND devices.
-
-config MTD_NAND_FSL_UPM
- tristate "Support for NAND on Freescale UPM"
- depends on PPC_83xx || PPC_85xx
- select FSL_LBC
- help
- Enables support for NAND Flash chips wired onto Freescale PowerPC
- processor localbus with User-Programmable Machine support.
-
-config MTD_NAND_MPC5121_NFC
- tristate "MPC5121 built-in NAND Flash Controller support"
- depends on PPC_MPC512x
- help
- This enables the driver for the NAND flash controller on the
- MPC5121 SoC.
-
-config MTD_NAND_VF610_NFC
- tristate "Support for Freescale NFC for VF610/MPC5125"
- depends on (SOC_VF610 || COMPILE_TEST)
- depends on HAS_IOMEM
- help
- Enables support for NAND Flash Controller on some Freescale
- processors like the VF610, MPC5125, MCF54418 or Kinetis K70.
- The driver supports a maximum 2k page size. With 2k pages and
- 64 bytes or more of OOB, hardware ECC with up to 32-bit error
- correction is supported. Hardware ECC is only enabled through
- device tree.
-
-config MTD_NAND_MXC
- tristate "MXC NAND support"
- depends on ARCH_MXC
- help
- This enables the driver for the NAND flash controller on the
- MXC processors.
-
-config MTD_NAND_SH_FLCTL
- tristate "Support for NAND on Renesas SuperH FLCTL"
- depends on SUPERH || COMPILE_TEST
- depends on HAS_IOMEM
- depends on HAS_DMA
- help
- Several Renesas SuperH CPU has FLCTL. This option enables support
- for NAND Flash using FLCTL.
-
-config MTD_NAND_DAVINCI
- tristate "Support NAND on DaVinci/Keystone SoC"
- depends on ARCH_DAVINCI || (ARCH_KEYSTONE && TI_AEMIF)
- help
- Enable the driver for NAND flash chips on Texas Instruments
- DaVinci/Keystone processors.
-
-config MTD_NAND_TXX9NDFMC
- tristate "NAND Flash support for TXx9 SoC"
- depends on SOC_TX4938 || SOC_TX4939
- help
- This enables the NAND flash controller on the TXx9 SoCs.
-
-config MTD_NAND_SOCRATES
- tristate "Support for NAND on Socrates board"
- depends on SOCRATES
- help
- Enables support for NAND Flash chips wired onto Socrates board.
-
-config MTD_NAND_NUC900
- tristate "Support for NAND on Nuvoton NUC9xx/w90p910 evaluation boards."
- depends on ARCH_W90X900
- help
- This enables the driver for the NAND Flash on evaluation board based
- on w90p910 / NUC9xx.
-
-config MTD_NAND_JZ4740
- tristate "Support for JZ4740 SoC NAND controller"
- depends on MACH_JZ4740
- help
- Enables support for NAND Flash on JZ4740 SoC based boards.
-
-config MTD_NAND_JZ4780
- tristate "Support for NAND on JZ4780 SoC"
- depends on MACH_JZ4780 && JZ4780_NEMC
- help
- Enables support for NAND Flash connected to the NEMC on JZ4780 SoC
- based boards, using the BCH controller for hardware error correction.
-
-config MTD_NAND_FSMC
- tristate "Support for NAND on ST Micros FSMC"
- depends on OF
- depends on PLAT_SPEAR || ARCH_NOMADIK || ARCH_U8500 || MACH_U300
- help
- Enables support for NAND Flash chips on the ST Microelectronics
- Flexible Static Memory Controller (FSMC)
-
-config MTD_NAND_XWAY
- bool "Support for NAND on Lantiq XWAY SoC"
- depends on LANTIQ && SOC_TYPE_XWAY
- help
- Enables support for NAND Flash chips on Lantiq XWAY SoCs. NAND is attached
- to the External Bus Unit (EBU).
-
-config MTD_NAND_SUNXI
- tristate "Support for NAND on Allwinner SoCs"
- depends on ARCH_SUNXI
- help
- Enables support for NAND Flash chips on Allwinner SoCs.
-
-config MTD_NAND_HISI504
- tristate "Support for NAND controller on Hisilicon SoC Hip04"
- depends on ARCH_HISI || COMPILE_TEST
- depends on HAS_DMA
- help
- Enables support for NAND controller on Hisilicon SoC Hip04.
-
-config MTD_NAND_QCOM
- tristate "Support for NAND on QCOM SoCs"
- depends on ARCH_QCOM
- help
- Enables support for NAND flash chips on SoCs containing the EBI2 NAND
- controller. This controller is found on IPQ806x SoC.
-
-config MTD_NAND_MTK
- tristate "Support for NAND controller on MTK SoCs"
- depends on ARCH_MEDIATEK || COMPILE_TEST
- depends on HAS_DMA
- help
- Enables support for NAND controller on MTK SoCs.
- This controller is found on mt27xx, mt81xx, mt65xx SoCs.
-
-endif # MTD_NAND
+source "drivers/mtd/nand/raw/Kconfig"
git.samba.org / sfrench / cifs-2.6.git / blobdiff