powerpc: Remove arch/ppc and include/asm-ppc

[sfrench/cifs-2.6.git] / arch / ppc / platforms / sandpoint.h

diff --git a/arch/ppc/platforms/sandpoint.h b/arch/ppc/platforms/sandpoint.h
deleted file mode 100644 (file)
index ed83759..0000000
--- a/arch/ppc/platforms/sandpoint.h
+++ /dev/null
@@ -1,75 +0,0 @@
-/*
- * Definitions for Motorola SPS Sandpoint Test Platform
- *
- * Author: Mark A. Greer
- *         mgreer@mvista.com
- *
- * 2000-2003 (c) MontaVista, Software, Inc.  This file is licensed under
- * the terms of the GNU General Public License version 2.  This program
- * is licensed "as is" without any warranty of any kind, whether express
- * or implied.
- */
-
-/*
- * Sandpoint uses the CHRP map (Map B).
- */
-
-#ifndef __PPC_PLATFORMS_SANDPOINT_H
-#define __PPC_PLATFORMS_SANDPOINT_H
-
-#include <asm/ppcboot.h>
-
-#if 0
-/* The Sandpoint X3 allows the IDE interrupt to be directly connected
- * from the Windbond (PCI INTC or INTD) to the serial EPIC.  Someday
- * we should try this, but it was easier to use the existing 83c553
- * initialization than change it to route the different interrupts :-).
- *     -- Dan
- */
-#define SANDPOINT_IDE_INT0             23      /* EPIC 7 */
-#define SANDPOINT_IDE_INT1             24      /* EPIC 8 */
-#endif
-
-/*
- * The sandpoint boards have processor modules that either have an 8240 or
- * an MPC107 host bridge on them.  These bridges have an IDSEL line that allows
- * them to respond to PCI transactions as if they were a normal PCI devices.
- * However, the processor on the processor side of the bridge can not reach
- * out onto the PCI bus and then select the bridge or bad things will happen
- * (documented in the 8240 and 107 manuals).
- * Because of this, we always skip the bridge PCI device when accessing the
- * PCI bus.  The PCI slot that the bridge occupies is defined by the macro
- * below.
- */
-#define SANDPOINT_HOST_BRIDGE_IDSEL     12
-
-/*
- * Serial defines.
- */
-#define SANDPOINT_SERIAL_0             0xfe0003f8
-#define SANDPOINT_SERIAL_1             0xfe0002f8
-
-#define RS_TABLE_SIZE  2
-
-/* Rate for the 1.8432 Mhz clock for the onboard serial chip */
-#define BASE_BAUD                      ( 1843200 / 16 )
-#define UART_CLK                       1843200
-
-#ifdef CONFIG_SERIAL_DETECT_IRQ
-#define STD_COM_FLAGS (ASYNC_BOOT_AUTOCONF|ASYNC_AUTO_IRQ)
-#else
-#define STD_COM_FLAGS (ASYNC_BOOT_AUTOCONF)
-#endif
-
-#define STD_SERIAL_PORT_DFNS \
-        { 0, BASE_BAUD, SANDPOINT_SERIAL_0, 4, STD_COM_FLAGS, /* ttyS0 */ \
-               iomem_base: (u8 *)SANDPOINT_SERIAL_0,                     \
-               io_type: SERIAL_IO_MEM },                                 \
-        { 0, BASE_BAUD, SANDPOINT_SERIAL_1, 3, STD_COM_FLAGS, /* ttyS1 */ \
-               iomem_base: (u8 *)SANDPOINT_SERIAL_1,                     \
-               io_type: SERIAL_IO_MEM },
-
-#define SERIAL_PORT_DFNS \
-        STD_SERIAL_PORT_DFNS
-
-#endif /* __PPC_PLATFORMS_SANDPOINT_H */