+++ /dev/null
-/*
- * Copyright 2004-2009 Analog Devices Inc.
- * 2005 National ICT Australia (NICTA)
- * Aidan Williams <aidan@nicta.com.au>
- *
- * Licensed under the GPL-2 or later.
- */
-
-#include <linux/device.h>
-#include <linux/export.h>
-#include <linux/platform_device.h>
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/partitions.h>
-#include <linux/mtd/physmap.h>
-#include <linux/spi/spi.h>
-#include <linux/spi/flash.h>
-
-#include <linux/i2c.h>
-#include <linux/irq.h>
-#include <linux/interrupt.h>
-#include <linux/usb/musb.h>
-#include <asm/dma.h>
-#include <asm/bfin5xx_spi.h>
-#include <asm/reboot.h>
-#include <asm/nand.h>
-#include <asm/portmux.h>
-#include <asm/dpmc.h>
-#include <linux/spi/ad7877.h>
-
-/*
- * Name the Board for the /proc/cpuinfo
- */
-const char bfin_board_name[] = "ADI BF526-EZBRD";
-
-/*
- * Driver needs to know address, irq and flag pin.
- */
-
-#if IS_ENABLED(CONFIG_USB_MUSB_HDRC)
-static struct resource musb_resources[] = {
- [0] = {
- .start = 0xffc03800,
- .end = 0xffc03cff,
- .flags = IORESOURCE_MEM,
- },
- [1] = { /* general IRQ */
- .start = IRQ_USB_INT0,
- .end = IRQ_USB_INT0,
- .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
- .name = "mc"
- },
- [2] = { /* DMA IRQ */
- .start = IRQ_USB_DMA,
- .end = IRQ_USB_DMA,
- .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
- .name = "dma"
- },
-};
-
-static struct musb_hdrc_config musb_config = {
- .multipoint = 0,
- .dyn_fifo = 0,
- .soft_con = 1,
- .dma = 1,
- .num_eps = 8,
- .dma_channels = 8,
- .gpio_vrsel = GPIO_PG13,
- /* Some custom boards need to be active low, just set it to "0"
- * if it is the case.
- */
- .gpio_vrsel_active = 1,
- .clkin = 24, /* musb CLKIN in MHZ */
-};
-
-static struct musb_hdrc_platform_data musb_plat = {
-#if defined(CONFIG_USB_MUSB_OTG)
- .mode = MUSB_OTG,
-#elif defined(CONFIG_USB_MUSB_HDRC_HCD)
- .mode = MUSB_HOST,
-#elif defined(CONFIG_USB_GADGET_MUSB_HDRC)
- .mode = MUSB_PERIPHERAL,
-#endif
- .config = &musb_config,
-};
-
-static u64 musb_dmamask = ~(u32)0;
-
-static struct platform_device musb_device = {
- .name = "musb-blackfin",
- .id = 0,
- .dev = {
- .dma_mask = &musb_dmamask,
- .coherent_dma_mask = 0xffffffff,
- .platform_data = &musb_plat,
- },
- .num_resources = ARRAY_SIZE(musb_resources),
- .resource = musb_resources,
-};
-#endif
-
-#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
-static struct mtd_partition ezbrd_partitions[] = {
- {
- .name = "bootloader(nor)",
- .size = 0x40000,
- .offset = 0,
- }, {
- .name = "linux kernel(nor)",
- .size = 0x1C0000,
- .offset = MTDPART_OFS_APPEND,
- }, {
- .name = "file system(nor)",
- .size = MTDPART_SIZ_FULL,
- .offset = MTDPART_OFS_APPEND,
- }
-};
-
-static struct physmap_flash_data ezbrd_flash_data = {
- .width = 2,
- .parts = ezbrd_partitions,
- .nr_parts = ARRAY_SIZE(ezbrd_partitions),
-};
-
-static struct resource ezbrd_flash_resource = {
- .start = 0x20000000,
- .end = 0x203fffff,
- .flags = IORESOURCE_MEM,
-};
-
-static struct platform_device ezbrd_flash_device = {
- .name = "physmap-flash",
- .id = 0,
- .dev = {
- .platform_data = &ezbrd_flash_data,
- },
- .num_resources = 1,
- .resource = &ezbrd_flash_resource,
-};
-#endif
-
-#if IS_ENABLED(CONFIG_MTD_NAND_BF5XX)
-static struct mtd_partition partition_info[] = {
- {
- .name = "bootloader(nand)",
- .offset = 0,
- .size = 0x40000,
- }, {
- .name = "linux kernel(nand)",
- .offset = MTDPART_OFS_APPEND,
- .size = 4 * 1024 * 1024,
- },
- {
- .name = "file system(nand)",
- .offset = MTDPART_OFS_APPEND,
- .size = MTDPART_SIZ_FULL,
- },
-};
-
-static struct bf5xx_nand_platform bf5xx_nand_platform = {
- .data_width = NFC_NWIDTH_8,
- .partitions = partition_info,
- .nr_partitions = ARRAY_SIZE(partition_info),
- .rd_dly = 3,
- .wr_dly = 3,
-};
-
-static struct resource bf5xx_nand_resources[] = {
- {
- .start = NFC_CTL,
- .end = NFC_DATA_RD + 2,
- .flags = IORESOURCE_MEM,
- },
- {
- .start = CH_NFC,
- .end = CH_NFC,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device bf5xx_nand_device = {
- .name = "bf5xx-nand",
- .id = 0,
- .num_resources = ARRAY_SIZE(bf5xx_nand_resources),
- .resource = bf5xx_nand_resources,
- .dev = {
- .platform_data = &bf5xx_nand_platform,
- },
-};
-#endif
-
-#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
-static struct platform_device rtc_device = {
- .name = "rtc-bfin",
- .id = -1,
-};
-#endif
-
-
-#if IS_ENABLED(CONFIG_BFIN_MAC)
-#include <linux/bfin_mac.h>
-static const unsigned short bfin_mac_peripherals[] = P_RMII0;
-
-static struct bfin_phydev_platform_data bfin_phydev_data[] = {
- {
- .addr = 1,
- .irq = IRQ_MAC_PHYINT,
- },
-};
-
-static struct bfin_mii_bus_platform_data bfin_mii_bus_data = {
- .phydev_number = 1,
- .phydev_data = bfin_phydev_data,
- .phy_mode = PHY_INTERFACE_MODE_RMII,
- .mac_peripherals = bfin_mac_peripherals,
-};
-
-static struct platform_device bfin_mii_bus = {
- .name = "bfin_mii_bus",
- .dev = {
- .platform_data = &bfin_mii_bus_data,
- }
-};
-
-static struct platform_device bfin_mac_device = {
- .name = "bfin_mac",
- .dev = {
- .platform_data = &bfin_mii_bus,
- }
-};
-#endif
-
-#if IS_ENABLED(CONFIG_MTD_M25P80)
-static struct mtd_partition bfin_spi_flash_partitions[] = {
- {
- .name = "bootloader(spi)",
- .size = 0x00040000,
- .offset = 0,
- .mask_flags = MTD_CAP_ROM
- }, {
- .name = "linux kernel(spi)",
- .size = MTDPART_SIZ_FULL,
- .offset = MTDPART_OFS_APPEND,
- }
-};
-
-static struct flash_platform_data bfin_spi_flash_data = {
- .name = "m25p80",
- .parts = bfin_spi_flash_partitions,
- .nr_parts = ARRAY_SIZE(bfin_spi_flash_partitions),
- .type = "sst25wf040",
-};
-
-/* SPI flash chip (sst25wf040) */
-static struct bfin5xx_spi_chip spi_flash_chip_info = {
- .enable_dma = 0, /* use dma transfer with this chip*/
-};
-#endif
-
-#if IS_ENABLED(CONFIG_MMC_SPI)
-static struct bfin5xx_spi_chip mmc_spi_chip_info = {
- .enable_dma = 0,
-};
-#endif
-
-#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7877)
-static const struct ad7877_platform_data bfin_ad7877_ts_info = {
- .model = 7877,
- .vref_delay_usecs = 50, /* internal, no capacitor */
- .x_plate_ohms = 419,
- .y_plate_ohms = 486,
- .pressure_max = 1000,
- .pressure_min = 0,
- .stopacq_polarity = 1,
- .first_conversion_delay = 3,
- .acquisition_time = 1,
- .averaging = 1,
- .pen_down_acc_interval = 1,
-};
-#endif
-
-#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7879)
-#include <linux/platform_data/ad7879.h>
-static const struct ad7879_platform_data bfin_ad7879_ts_info = {
- .model = 7879, /* Model = AD7879 */
- .x_plate_ohms = 620, /* 620 Ohm from the touch datasheet */
- .pressure_max = 10000,
- .pressure_min = 0,
- .first_conversion_delay = 3, /* wait 512us before do a first conversion */
- .acquisition_time = 1, /* 4us acquisition time per sample */
- .median = 2, /* do 8 measurements */
- .averaging = 1, /* take the average of 4 middle samples */
- .pen_down_acc_interval = 255, /* 9.4 ms */
- .gpio_export = 1, /* Export GPIO to gpiolib */
- .gpio_base = -1, /* Dynamic allocation */
-};
-#endif
-
-static struct spi_board_info bfin_spi_board_info[] __initdata = {
-#if IS_ENABLED(CONFIG_MTD_M25P80)
- {
- /* the modalias must be the same as spi device driver name */
- .modalias = "m25p80", /* Name of spi_driver for this device */
- .max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 0, /* Framework bus number */
- .chip_select = 1, /* Framework chip select. On STAMP537 it is SPISSEL1*/
- .platform_data = &bfin_spi_flash_data,
- .controller_data = &spi_flash_chip_info,
- .mode = SPI_MODE_3,
- },
-#endif
-
-#if IS_ENABLED(CONFIG_MMC_SPI)
- {
- .modalias = "mmc_spi",
- .max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 0,
- .chip_select = 5,
- .controller_data = &mmc_spi_chip_info,
- .mode = SPI_MODE_3,
- },
-#endif
-#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7877)
- {
- .modalias = "ad7877",
- .platform_data = &bfin_ad7877_ts_info,
- .irq = IRQ_PF8,
- .max_speed_hz = 12500000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 0,
- .chip_select = 2,
- },
-#endif
-#if IS_ENABLED(CONFIG_TOUCHSCREEN_AD7879_SPI)
- {
- .modalias = "ad7879",
- .platform_data = &bfin_ad7879_ts_info,
- .irq = IRQ_PG0,
- .max_speed_hz = 5000000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 0,
- .chip_select = 5,
- .mode = SPI_CPHA | SPI_CPOL,
- },
-#endif
-#if IS_ENABLED(CONFIG_SND_SOC_WM8731) \
- && defined(CONFIG_SND_SOC_WM8731_SPI)
- {
- .modalias = "wm8731",
- .max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 0,
- .chip_select = 5,
- .mode = SPI_MODE_0,
- },
-#endif
-#if IS_ENABLED(CONFIG_SPI_SPIDEV)
- {
- .modalias = "spidev",
- .max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 0,
- .chip_select = 1,
- },
-#endif
-#if IS_ENABLED(CONFIG_FB_BFIN_LQ035Q1)
- {
- .modalias = "bfin-lq035q1-spi",
- .max_speed_hz = 20000000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 0,
- .chip_select = 1,
- .mode = SPI_CPHA | SPI_CPOL,
- },
-#endif
-};
-
-#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
-/* SPI controller data */
-static struct bfin5xx_spi_master bfin_spi0_info = {
- .num_chipselect = 8,
- .enable_dma = 1, /* master has the ability to do dma transfer */
- .pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0},
-};
-
-/* SPI (0) */
-static struct resource bfin_spi0_resource[] = {
- [0] = {
- .start = SPI0_REGBASE,
- .end = SPI0_REGBASE + 0xFF,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = CH_SPI,
- .end = CH_SPI,
- .flags = IORESOURCE_DMA,
- },
- [2] = {
- .start = IRQ_SPI,
- .end = IRQ_SPI,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device bfin_spi0_device = {
- .name = "bfin-spi",
- .id = 0, /* Bus number */
- .num_resources = ARRAY_SIZE(bfin_spi0_resource),
- .resource = bfin_spi0_resource,
- .dev = {
- .platform_data = &bfin_spi0_info, /* Passed to driver */
- },
-};
-#endif /* spi master and devices */
-
-#if IS_ENABLED(CONFIG_SERIAL_BFIN)
-#ifdef CONFIG_SERIAL_BFIN_UART0
-static struct resource bfin_uart0_resources[] = {
- {
- .start = UART0_THR,
- .end = UART0_GCTL+2,
- .flags = IORESOURCE_MEM,
- },
- {
- .start = IRQ_UART0_TX,
- .end = IRQ_UART0_TX,
- .flags = IORESOURCE_IRQ,
- },
- {
- .start = IRQ_UART0_RX,
- .end = IRQ_UART0_RX,
- .flags = IORESOURCE_IRQ,
- },
- {
- .start = IRQ_UART0_ERROR,
- .end = IRQ_UART0_ERROR,
- .flags = IORESOURCE_IRQ,
- },
- {
- .start = CH_UART0_TX,
- .end = CH_UART0_TX,
- .flags = IORESOURCE_DMA,
- },
- {
- .start = CH_UART0_RX,
- .end = CH_UART0_RX,
- .flags = IORESOURCE_DMA,
- },
-};
-
-static unsigned short bfin_uart0_peripherals[] = {
- P_UART0_TX, P_UART0_RX, 0
-};
-
-static struct platform_device bfin_uart0_device = {
- .name = "bfin-uart",
- .id = 0,
- .num_resources = ARRAY_SIZE(bfin_uart0_resources),
- .resource = bfin_uart0_resources,
- .dev = {
- .platform_data = &bfin_uart0_peripherals, /* Passed to driver */
- },
-};
-#endif
-#ifdef CONFIG_SERIAL_BFIN_UART1
-static struct resource bfin_uart1_resources[] = {
- {
- .start = UART1_THR,
- .end = UART1_GCTL+2,
- .flags = IORESOURCE_MEM,
- },
- {
- .start = IRQ_UART1_TX,
- .end = IRQ_UART1_TX,
- .flags = IORESOURCE_IRQ,
- },
- {
- .start = IRQ_UART1_RX,
- .end = IRQ_UART1_RX,
- .flags = IORESOURCE_IRQ,
- },
- {
- .start = IRQ_UART1_ERROR,
- .end = IRQ_UART1_ERROR,
- .flags = IORESOURCE_IRQ,
- },
- {
- .start = CH_UART1_TX,
- .end = CH_UART1_TX,
- .flags = IORESOURCE_DMA,
- },
- {
- .start = CH_UART1_RX,
- .end = CH_UART1_RX,
- .flags = IORESOURCE_DMA,
- },
-#ifdef CONFIG_BFIN_UART1_CTSRTS
- { /* CTS pin */
- .start = GPIO_PG0,
- .end = GPIO_PG0,
- .flags = IORESOURCE_IO,
- },
- { /* RTS pin */
- .start = GPIO_PF10,
- .end = GPIO_PF10,
- .flags = IORESOURCE_IO,
- },
-#endif
-};
-
-static unsigned short bfin_uart1_peripherals[] = {
- P_UART1_TX, P_UART1_RX, 0
-};
-
-static struct platform_device bfin_uart1_device = {
- .name = "bfin-uart",
- .id = 1,
- .num_resources = ARRAY_SIZE(bfin_uart1_resources),
- .resource = bfin_uart1_resources,
- .dev = {
- .platform_data = &bfin_uart1_peripherals, /* Passed to driver */
- },
-};
-#endif
-#endif
-
-#if IS_ENABLED(CONFIG_BFIN_SIR)
-#ifdef CONFIG_BFIN_SIR0
-static struct resource bfin_sir0_resources[] = {
- {
- .start = 0xFFC00400,
- .end = 0xFFC004FF,
- .flags = IORESOURCE_MEM,
- },
- {
- .start = IRQ_UART0_RX,
- .end = IRQ_UART0_RX+1,
- .flags = IORESOURCE_IRQ,
- },
- {
- .start = CH_UART0_RX,
- .end = CH_UART0_RX+1,
- .flags = IORESOURCE_DMA,
- },
-};
-
-static struct platform_device bfin_sir0_device = {
- .name = "bfin_sir",
- .id = 0,
- .num_resources = ARRAY_SIZE(bfin_sir0_resources),
- .resource = bfin_sir0_resources,
-};
-#endif
-#ifdef CONFIG_BFIN_SIR1
-static struct resource bfin_sir1_resources[] = {
- {
- .start = 0xFFC02000,
- .end = 0xFFC020FF,
- .flags = IORESOURCE_MEM,
- },
- {
- .start = IRQ_UART1_RX,
- .end = IRQ_UART1_RX+1,
- .flags = IORESOURCE_IRQ,
- },
- {
- .start = CH_UART1_RX,
- .end = CH_UART1_RX+1,
- .flags = IORESOURCE_DMA,
- },
-};
-
-static struct platform_device bfin_sir1_device = {
- .name = "bfin_sir",
- .id = 1,
- .num_resources = ARRAY_SIZE(bfin_sir1_resources),
- .resource = bfin_sir1_resources,
-};
-#endif
-#endif
-
-#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
-static const u16 bfin_twi0_pins[] = {P_TWI0_SCL, P_TWI0_SDA, 0};
-
-static struct resource bfin_twi0_resource[] = {
- [0] = {
- .start = TWI0_REGBASE,
- .end = TWI0_REGBASE,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = IRQ_TWI,
- .end = IRQ_TWI,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device i2c_bfin_twi_device = {
- .name = "i2c-bfin-twi",
- .id = 0,
- .num_resources = ARRAY_SIZE(bfin_twi0_resource),
- .resource = bfin_twi0_resource,
- .dev = {
- .platform_data = &bfin_twi0_pins,
- },
-};
-#endif
-
-static struct i2c_board_info __initdata bfin_i2c_board_info[] = {
-#if IS_ENABLED(CONFIG_BFIN_TWI_LCD)
- {
- I2C_BOARD_INFO("pcf8574_lcd", 0x22),
- },
-#endif
-#if IS_ENABLED(CONFIG_INPUT_PCF8574)
- {
- I2C_BOARD_INFO("pcf8574_keypad", 0x27),
- .irq = IRQ_PF8,
- },
-#endif
-};
-
-#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
-#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
-static struct resource bfin_sport0_uart_resources[] = {
- {
- .start = SPORT0_TCR1,
- .end = SPORT0_MRCS3+4,
- .flags = IORESOURCE_MEM,
- },
- {
- .start = IRQ_SPORT0_RX,
- .end = IRQ_SPORT0_RX+1,
- .flags = IORESOURCE_IRQ,
- },
- {
- .start = IRQ_SPORT0_ERROR,
- .end = IRQ_SPORT0_ERROR,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static unsigned short bfin_sport0_peripherals[] = {
- P_SPORT0_TFS, P_SPORT0_DTPRI, P_SPORT0_TSCLK, P_SPORT0_RFS,
- P_SPORT0_DRPRI, P_SPORT0_RSCLK, 0
-};
-
-static struct platform_device bfin_sport0_uart_device = {
- .name = "bfin-sport-uart",
- .id = 0,
- .num_resources = ARRAY_SIZE(bfin_sport0_uart_resources),
- .resource = bfin_sport0_uart_resources,
- .dev = {
- .platform_data = &bfin_sport0_peripherals, /* Passed to driver */
- },
-};
-#endif
-#ifdef CONFIG_SERIAL_BFIN_SPORT1_UART
-static struct resource bfin_sport1_uart_resources[] = {
- {
- .start = SPORT1_TCR1,
- .end = SPORT1_MRCS3+4,
- .flags = IORESOURCE_MEM,
- },
- {
- .start = IRQ_SPORT1_RX,
- .end = IRQ_SPORT1_RX+1,
- .flags = IORESOURCE_IRQ,
- },
- {
- .start = IRQ_SPORT1_ERROR,
- .end = IRQ_SPORT1_ERROR,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static unsigned short bfin_sport1_peripherals[] = {
- P_SPORT1_TFS, P_SPORT1_DTPRI, P_SPORT1_TSCLK, P_SPORT1_RFS,
- P_SPORT1_DRPRI, P_SPORT1_RSCLK, 0
-};
-
-static struct platform_device bfin_sport1_uart_device = {
- .name = "bfin-sport-uart",
- .id = 1,
- .num_resources = ARRAY_SIZE(bfin_sport1_uart_resources),
- .resource = bfin_sport1_uart_resources,
- .dev = {
- .platform_data = &bfin_sport1_peripherals, /* Passed to driver */
- },
-};
-#endif
-#endif
-
-#if IS_ENABLED(CONFIG_KEYBOARD_GPIO)
-#include <linux/input.h>
-#include <linux/gpio_keys.h>
-
-static struct gpio_keys_button bfin_gpio_keys_table[] = {
- {BTN_0, GPIO_PG0, 1, "gpio-keys: BTN0"},
- {BTN_1, GPIO_PG13, 1, "gpio-keys: BTN1"},
-};
-
-static struct gpio_keys_platform_data bfin_gpio_keys_data = {
- .buttons = bfin_gpio_keys_table,
- .nbuttons = ARRAY_SIZE(bfin_gpio_keys_table),
-};
-
-static struct platform_device bfin_device_gpiokeys = {
- .name = "gpio-keys",
- .dev = {
- .platform_data = &bfin_gpio_keys_data,
- },
-};
-#endif
-
-static const unsigned int cclk_vlev_datasheet[] =
-{
- VRPAIR(VLEV_100, 400000000),
- VRPAIR(VLEV_105, 426000000),
- VRPAIR(VLEV_110, 500000000),
- VRPAIR(VLEV_115, 533000000),
- VRPAIR(VLEV_120, 600000000),
-};
-
-static struct bfin_dpmc_platform_data bfin_dmpc_vreg_data = {
- .tuple_tab = cclk_vlev_datasheet,
- .tabsize = ARRAY_SIZE(cclk_vlev_datasheet),
- .vr_settling_time = 25 /* us */,
-};
-
-static struct platform_device bfin_dpmc = {
- .name = "bfin dpmc",
- .dev = {
- .platform_data = &bfin_dmpc_vreg_data,
- },
-};
-
-#if IS_ENABLED(CONFIG_FB_BFIN_LQ035Q1)
-#include <asm/bfin-lq035q1.h>
-
-static struct bfin_lq035q1fb_disp_info bfin_lq035q1_data = {
- .mode = LQ035_NORM | LQ035_RGB | LQ035_RL | LQ035_TB,
- .ppi_mode = USE_RGB565_16_BIT_PPI,
- .use_bl = 1,
- .gpio_bl = GPIO_PG12,
-};
-
-static struct resource bfin_lq035q1_resources[] = {
- {
- .start = IRQ_PPI_ERROR,
- .end = IRQ_PPI_ERROR,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device bfin_lq035q1_device = {
- .name = "bfin-lq035q1",
- .id = -1,
- .num_resources = ARRAY_SIZE(bfin_lq035q1_resources),
- .resource = bfin_lq035q1_resources,
- .dev = {
- .platform_data = &bfin_lq035q1_data,
- },
-};
-#endif
-
-static struct platform_device *stamp_devices[] __initdata = {
-
- &bfin_dpmc,
-
-#if IS_ENABLED(CONFIG_MTD_NAND_BF5XX)
- &bf5xx_nand_device,
-#endif
-
-#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
- &rtc_device,
-#endif
-
-#if IS_ENABLED(CONFIG_USB_MUSB_HDRC)
- &musb_device,
-#endif
-
-#if IS_ENABLED(CONFIG_BFIN_MAC)
- &bfin_mii_bus,
- &bfin_mac_device,
-#endif
-
-#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
- &bfin_spi0_device,
-#endif
-
-#if IS_ENABLED(CONFIG_SERIAL_BFIN)
-#ifdef CONFIG_SERIAL_BFIN_UART0
- &bfin_uart0_device,
-#endif
-#ifdef CONFIG_SERIAL_BFIN_UART1
- &bfin_uart1_device,
-#endif
-#endif
-
-#if IS_ENABLED(CONFIG_FB_BFIN_LQ035Q1)
- &bfin_lq035q1_device,
-#endif
-
-#if IS_ENABLED(CONFIG_BFIN_SIR)
-#ifdef CONFIG_BFIN_SIR0
- &bfin_sir0_device,
-#endif
-#ifdef CONFIG_BFIN_SIR1
- &bfin_sir1_device,
-#endif
-#endif
-
-#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
- &i2c_bfin_twi_device,
-#endif
-
-#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
-#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
- &bfin_sport0_uart_device,
-#endif
-#ifdef CONFIG_SERIAL_BFIN_SPORT1_UART
- &bfin_sport1_uart_device,
-#endif
-#endif
-
-#if IS_ENABLED(CONFIG_KEYBOARD_GPIO)
- &bfin_device_gpiokeys,
-#endif
-
-#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
- &ezbrd_flash_device,
-#endif
-};
-
-static int __init ezbrd_init(void)
-{
- printk(KERN_INFO "%s(): registering device resources\n", __func__);
- i2c_register_board_info(0, bfin_i2c_board_info,
- ARRAY_SIZE(bfin_i2c_board_info));
- platform_add_devices(stamp_devices, ARRAY_SIZE(stamp_devices));
- spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
- return 0;
-}
-
-arch_initcall(ezbrd_init);
-
-static struct platform_device *ezbrd_early_devices[] __initdata = {
-#if defined(CONFIG_SERIAL_BFIN_CONSOLE) || defined(CONFIG_EARLY_PRINTK)
-#ifdef CONFIG_SERIAL_BFIN_UART0
- &bfin_uart0_device,
-#endif
-#ifdef CONFIG_SERIAL_BFIN_UART1
- &bfin_uart1_device,
-#endif
-#endif
-
-#if defined(CONFIG_SERIAL_BFIN_SPORT_CONSOLE)
-#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
- &bfin_sport0_uart_device,
-#endif
-#ifdef CONFIG_SERIAL_BFIN_SPORT1_UART
- &bfin_sport1_uart_device,
-#endif
-#endif
-};
-
-void __init native_machine_early_platform_add_devices(void)
-{
- printk(KERN_INFO "register early platform devices\n");
- early_platform_add_devices(ezbrd_early_devices,
- ARRAY_SIZE(ezbrd_early_devices));
-}
-
-void native_machine_restart(char *cmd)
-{
- /* workaround reboot hang when booting from SPI */
- if ((bfin_read_SYSCR() & 0x7) == 0x3)
- bfin_reset_boot_spi_cs(P_DEFAULT_BOOT_SPI_CS);
-}
-
-int bfin_get_ether_addr(char *addr)
-{
- /* the MAC is stored in OTP memory page 0xDF */
- u32 ret;
- u64 otp_mac;
- u32 (*otp_read)(u32 page, u32 flags, u64 *page_content) = (void *)0xEF00001A;
-
- ret = otp_read(0xDF, 0x00, &otp_mac);
- if (!(ret & 0x1)) {
- char *otp_mac_p = (char *)&otp_mac;
- for (ret = 0; ret < 6; ++ret)
- addr[ret] = otp_mac_p[5 - ret];
- }
- return 0;
-}
-EXPORT_SYMBOL(bfin_get_ether_addr);
git.samba.org / sfrench / cifs-2.6.git / blobdiff