avr32: remove support for AVR32 architecture

[sfrench/cifs-2.6.git] / arch / avr32 / boards / atstk1000 / Kconfig

diff --git a/arch/avr32/boards/atstk1000/Kconfig b/arch/avr32/boards/atstk1000/Kconfig
deleted file mode 100644 (file)
index 8dc4821..0000000
--- a/arch/avr32/boards/atstk1000/Kconfig
+++ /dev/null
@@ -1,109 +0,0 @@
-# STK1000 customization
-
-if BOARD_ATSTK1000
-
-choice
-       prompt "ATSTK1000 CPU daughterboard type"
-       default BOARD_ATSTK1002
-
-config BOARD_ATSTK1002
-       bool "ATSTK1002"
-       select CPU_AT32AP7000
-
-config BOARD_ATSTK1003
-       bool "ATSTK1003"
-       select CPU_AT32AP7001
-
-config BOARD_ATSTK1004
-       bool "ATSTK1004"
-       select CPU_AT32AP7002
-
-config BOARD_ATSTK1006
-       bool "ATSTK1006"
-       select CPU_AT32AP7000
-
-endchoice
-
-
-config BOARD_ATSTK100X_CUSTOM
-       bool "Non-default STK1002/STK1003/STK1004 jumper settings"
-       help
-         You will normally leave the jumpers on the CPU card at their
-         default settings.  If you need to use certain peripherals,
-         you will need to change some of those jumpers.
-
-if BOARD_ATSTK100X_CUSTOM
-
-config BOARD_ATSTK100X_SW1_CUSTOM
-       bool "SW1: use SSC1 (not SPI0)"
-       help
-         This also prevents using the external DAC as an audio interface,
-         and means you can't initialize the on-board QVGA display.
-
-config BOARD_ATSTK100X_SW2_CUSTOM
-       bool "SW2: use IRDA or TIMER0 (not UART-A, MMC/SD, and PS2-A)"
-       help
-         If you change this you'll want an updated boot loader putting
-         the console on UART-C not UART-A.
-
-config BOARD_ATSTK100X_SW3_CUSTOM
-       bool "SW3: use TIMER1 (not SSC0 and GCLK)"
-       help
-         This also prevents using the external DAC as an audio interface.
-
-config BOARD_ATSTK100X_SW4_CUSTOM
-       bool "SW4: use ISI/Camera (not GPIOs, SPI1, and PS2-B)"
-       help
-         To use the camera interface you'll need a custom card (on the
-         PCI-format connector) connect a video sensor.
-
-config BOARD_ATSTK1002_SW5_CUSTOM
-       bool "SW5: use MACB1 (not LCDC)"
-       depends on BOARD_ATSTK1002
-
-config BOARD_ATSTK1002_SW6_CUSTOM
-       bool "SW6: more GPIOs (not MACB0)"
-       depends on BOARD_ATSTK1002
-
-endif  # custom
-
-config BOARD_ATSTK100X_SPI1
-       bool "Configure SPI1 controller"
-       depends on !BOARD_ATSTK100X_SW4_CUSTOM
-       help
-         All the signals for the second SPI controller are available on
-         GPIO lines and accessed through the J1 jumper block.  Say "y"
-         here to configure that SPI controller.
-
-config BOARD_ATSTK1000_J2_LED
-       bool
-       default BOARD_ATSTK1000_J2_LED8 || BOARD_ATSTK1000_J2_RGB
-
-choice
-       prompt "LEDs connected to J2:"
-       depends on LEDS_GPIO && !BOARD_ATSTK100X_SW4_CUSTOM
-       optional
-       help
-         Select this if you have jumpered the J2 jumper block to the
-         LED0..LED7 amber leds, or to the RGB leds, using a ten-pin
-         IDC cable.  A default "heartbeat" trigger is provided, but
-         you can of course override this.
-
-config BOARD_ATSTK1000_J2_LED8
-       bool "LED0..LED7"
-       help
-         Select this if J2 is jumpered to LED0..LED7 amber leds.
-
-config BOARD_ATSTK1000_J2_RGB
-       bool "RGB leds"
-       help
-         Select this if J2 is jumpered to the RGB leds.
-
-endchoice
-
-config BOARD_ATSTK1000_EXTDAC
-       bool
-       depends on !BOARD_ATSTK100X_SW1_CUSTOM && !BOARD_ATSTK100X_SW3_CUSTOM
-       default y
-
-endif  # stk 1000