+++ /dev/null
-Kernel driver smm665
-====================
-
-Supported chips:
-
- * Summit Microelectronics SMM465
-
- Prefix: 'smm465'
-
- Addresses scanned: -
-
- Datasheet:
-
- http://www.summitmicro.com/prod_select/summary/SMM465/SMM465DS.pdf
-
- * Summit Microelectronics SMM665, SMM665B
-
- Prefix: 'smm665'
-
- Addresses scanned: -
-
- Datasheet:
-
- http://www.summitmicro.com/prod_select/summary/SMM665/SMM665B_2089_20.pdf
-
- * Summit Microelectronics SMM665C
-
- Prefix: 'smm665c'
-
- Addresses scanned: -
-
- Datasheet:
-
- http://www.summitmicro.com/prod_select/summary/SMM665C/SMM665C_2125.pdf
-
- * Summit Microelectronics SMM764
-
- Prefix: 'smm764'
-
- Addresses scanned: -
-
- Datasheet:
-
- http://www.summitmicro.com/prod_select/summary/SMM764/SMM764_2098.pdf
-
- * Summit Microelectronics SMM766, SMM766B
-
- Prefix: 'smm766'
-
- Addresses scanned: -
-
- Datasheets:
-
- http://www.summitmicro.com/prod_select/summary/SMM766/SMM766_2086.pdf
-
- http://www.summitmicro.com/prod_select/summary/SMM766B/SMM766B_2122.pdf
-
-Author: Guenter Roeck <linux@roeck-us.net>
-
-
-Module Parameters
------------------
-
-* vref: int
- Default: 1250 (mV)
-
- Reference voltage on VREF_ADC pin in mV. It should not be necessary to set
- this parameter unless a non-default reference voltage is used.
-
-
-Description
------------
-
-[From datasheet] The SMM665 is an Active DC Output power supply Controller
-that monitors, margins and cascade sequences power. The part monitors six
-power supply channels as well as VDD, 12V input, two general-purpose analog
-inputs and an internal temperature sensor using a 10-bit ADC.
-
-Each monitored channel has its own high and low limits, plus a critical
-limit.
-
-Support for SMM465, SMM764, and SMM766 has been implemented but is untested.
-
-
-Usage Notes
------------
-
-This driver does not probe for devices, since there is no register which
-can be safely used to identify the chip. You will have to instantiate
-the devices explicitly. When instantiating the device, you have to specify
-its configuration register address.
-
-Example: the following will load the driver for an SMM665 at address 0x57
-on I2C bus #1::
-
- $ modprobe smm665
- $ echo smm665 0x57 > /sys/bus/i2c/devices/i2c-1/new_device
-
-
-Sysfs entries
--------------
-
-This driver uses the values in the datasheet to convert ADC register values
-into the values specified in the sysfs-interface document. All attributes are
-read only.
-
-Min, max, lcrit, and crit values are used by the chip to trigger external signals
-and/or other activity. Triggered signals can include HEALTHY, RST, Power Off,
-or Fault depending on the chip configuration. The driver reports values as lcrit
-or crit if exceeding the limits triggers RST, Power Off, or Fault, and as min or
-max otherwise. For details please see the SMM665 datasheet.
-
-For SMM465 and SMM764, values for Channel E and F are reported but undefined.
-
-======================= =======================================================
-in1_input 12V input voltage (mV)
-in2_input 3.3V (VDD) input voltage (mV)
-in3_input Channel A voltage (mV)
-in4_input Channel B voltage (mV)
-in5_input Channel C voltage (mV)
-in6_input Channel D voltage (mV)
-in7_input Channel E voltage (mV)
-in8_input Channel F voltage (mV)
-in9_input AIN1 voltage (mV)
-in10_input AIN2 voltage (mV)
-
-in1_min 12v input minimum voltage (mV)
-in2_min 3.3V (VDD) input minimum voltage (mV)
-in3_min Channel A minimum voltage (mV)
-in4_min Channel B minimum voltage (mV)
-in5_min Channel C minimum voltage (mV)
-in6_min Channel D minimum voltage (mV)
-in7_min Channel E minimum voltage (mV)
-in8_min Channel F minimum voltage (mV)
-in9_min AIN1 minimum voltage (mV)
-in10_min AIN2 minimum voltage (mV)
-
-in1_max 12v input maximum voltage (mV)
-in2_max 3.3V (VDD) input maximum voltage (mV)
-in3_max Channel A maximum voltage (mV)
-in4_max Channel B maximum voltage (mV)
-in5_max Channel C maximum voltage (mV)
-in6_max Channel D maximum voltage (mV)
-in7_max Channel E maximum voltage (mV)
-in8_max Channel F maximum voltage (mV)
-in9_max AIN1 maximum voltage (mV)
-in10_max AIN2 maximum voltage (mV)
-
-in1_lcrit 12v input critical minimum voltage (mV)
-in2_lcrit 3.3V (VDD) input critical minimum voltage (mV)
-in3_lcrit Channel A critical minimum voltage (mV)
-in4_lcrit Channel B critical minimum voltage (mV)
-in5_lcrit Channel C critical minimum voltage (mV)
-in6_lcrit Channel D critical minimum voltage (mV)
-in7_lcrit Channel E critical minimum voltage (mV)
-in8_lcrit Channel F critical minimum voltage (mV)
-in9_lcrit AIN1 critical minimum voltage (mV)
-in10_lcrit AIN2 critical minimum voltage (mV)
-
-in1_crit 12v input critical maximum voltage (mV)
-in2_crit 3.3V (VDD) input critical maximum voltage (mV)
-in3_crit Channel A critical maximum voltage (mV)
-in4_crit Channel B critical maximum voltage (mV)
-in5_crit Channel C critical maximum voltage (mV)
-in6_crit Channel D critical maximum voltage (mV)
-in7_crit Channel E critical maximum voltage (mV)
-in8_crit Channel F critical maximum voltage (mV)
-in9_crit AIN1 critical maximum voltage (mV)
-in10_crit AIN2 critical maximum voltage (mV)
-
-in1_crit_alarm 12v input critical alarm
-in2_crit_alarm 3.3V (VDD) input critical alarm
-in3_crit_alarm Channel A critical alarm
-in4_crit_alarm Channel B critical alarm
-in5_crit_alarm Channel C critical alarm
-in6_crit_alarm Channel D critical alarm
-in7_crit_alarm Channel E critical alarm
-in8_crit_alarm Channel F critical alarm
-in9_crit_alarm AIN1 critical alarm
-in10_crit_alarm AIN2 critical alarm
-
-temp1_input Chip temperature
-temp1_min Mimimum chip temperature
-temp1_max Maximum chip temperature
-temp1_crit Critical chip temperature
-temp1_crit_alarm Temperature critical alarm
-======================= =======================================================
git.samba.org / sfrench / cifs-2.6.git / blobdiff