--- /dev/null
+Qualcomm MSM8996 TLMM block
+
+This binding describes the Top Level Mode Multiplexer block found in the
+MSM8996 platform.
+
+- compatible:
+ Usage: required
+ Value type: <string>
+ Definition: must be "qcom,msm8996-pinctrl"
+
+- reg:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: the base address and size of the TLMM register space.
+
+- interrupts:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: should specify the TLMM summary IRQ.
+
+- interrupt-controller:
+ Usage: required
+ Value type: <none>
+ Definition: identifies this node as an interrupt controller
+
+- #interrupt-cells:
+ Usage: required
+ Value type: <u32>
+ Definition: must be 2. Specifying the pin number and flags, as defined
+ in <dt-bindings/interrupt-controller/irq.h>
+
+- gpio-controller:
+ Usage: required
+ Value type: <none>
+ Definition: identifies this node as a gpio controller
+
+- #gpio-cells:
+ Usage: required
+ Value type: <u32>
+ Definition: must be 2. Specifying the pin number and flags, as defined
+ in <dt-bindings/gpio/gpio.h>
+
+Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for
+a general description of GPIO and interrupt bindings.
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices, including the meaning of the
+phrase "pin configuration node".
+
+The pin configuration nodes act as a container for an arbitrary number of
+subnodes. Each of these subnodes represents some desired configuration for a
+pin, a group, or a list of pins or groups. This configuration can include the
+mux function to select on those pin(s)/group(s), and various pin configuration
+parameters, such as pull-up, drive strength, etc.
+
+
+PIN CONFIGURATION NODES:
+
+The name of each subnode is not important; all subnodes should be enumerated
+and processed purely based on their content.
+
+Each subnode only affects those parameters that are explicitly listed. In
+other words, a subnode that lists a mux function but no pin configuration
+parameters implies no information about any pin configuration parameters.
+Similarly, a pin subnode that describes a pullup parameter implies no
+information about e.g. the mux function.
+
+
+The following generic properties as defined in pinctrl-bindings.txt are valid
+to specify in a pin configuration subnode:
+
+- pins:
+ Usage: required
+ Value type: <string-array>
+ Definition: List of gpio pins affected by the properties specified in
+ this subnode.
+
+ Valid pins are:
+ gpio0-gpio149
+ Supports mux, bias and drive-strength
+
+ sdc1_clk, sdc1_cmd, sdc1_data sdc2_clk, sdc2_cmd,
+ sdc2_data sdc1_rclk
+ Supports bias and drive-strength
+
+- function:
+ Usage: required
+ Value type: <string>
+ Definition: Specify the alternative function to be configured for the
+ specified pins. Functions are only valid for gpio pins.
+ Valid values are:
+
+ blsp_uart1, blsp_spi1, blsp_i2c1, blsp_uim1, atest_tsens,
+ bimc_dte1, dac_calib0, blsp_spi8, blsp_uart8, blsp_uim8,
+ qdss_cti_trig_out_b, bimc_dte0, dac_calib1, qdss_cti_trig_in_b,
+ dac_calib2, atest_tsens2, atest_usb1, blsp_spi10, blsp_uart10,
+ blsp_uim10, atest_bbrx1, atest_usb13, atest_bbrx0, atest_usb12,
+ mdp_vsync, edp_lcd, blsp_i2c10, atest_gpsadc1, atest_usb11,
+ atest_gpsadc0, edp_hot, atest_usb10, m_voc, dac_gpio, atest_char,
+ cam_mclk, pll_bypassnl, qdss_stm7, blsp_i2c8, qdss_tracedata_b,
+ pll_reset, qdss_stm6, qdss_stm5, qdss_stm4, atest_usb2, cci_i2c,
+ qdss_stm3, dac_calib3, atest_usb23, atest_char3, dac_calib4,
+ qdss_stm2, atest_usb22, atest_char2, qdss_stm1, dac_calib5,
+ atest_usb21, atest_char1, dbg_out, qdss_stm0, dac_calib6,
+ atest_usb20, atest_char0, dac_calib10, qdss_stm10,
+ qdss_cti_trig_in_a, cci_timer4, blsp_spi6, blsp_uart6, blsp_uim6,
+ blsp2_spi, qdss_stm9, qdss_cti_trig_out_a, dac_calib11,
+ qdss_stm8, cci_timer0, qdss_stm13, dac_calib7, cci_timer1,
+ qdss_stm12, dac_calib8, cci_timer2, blsp1_spi, qdss_stm11,
+ dac_calib9, cci_timer3, cci_async, dac_calib12, blsp_i2c6,
+ qdss_tracectl_a, dac_calib13, qdss_traceclk_a, dac_calib14,
+ dac_calib15, hdmi_rcv, dac_calib16, hdmi_cec, pwr_modem,
+ dac_calib17, hdmi_ddc, pwr_nav, dac_calib18, pwr_crypto,
+ dac_calib19, hdmi_hot, dac_calib20, dac_calib21, pci_e0,
+ dac_calib22, dac_calib23, dac_calib24, tsif1_sync, dac_calib25,
+ sd_write, tsif1_error, blsp_spi2, blsp_uart2, blsp_uim2,
+ qdss_cti, blsp_i2c2, blsp_spi3, blsp_uart3, blsp_uim3, blsp_i2c3,
+ uim3, blsp_spi9, blsp_uart9, blsp_uim9, blsp10_spi, blsp_i2c9,
+ blsp_spi7, blsp_uart7, blsp_uim7, qdss_tracedata_a, blsp_i2c7,
+ qua_mi2s, gcc_gp1_clk_a, ssc_irq, uim4, blsp_spi11, blsp_uart11,
+ blsp_uim11, gcc_gp2_clk_a, gcc_gp3_clk_a, blsp_i2c11, cri_trng0,
+ cri_trng1, cri_trng, qdss_stm18, pri_mi2s, qdss_stm17, blsp_spi4,
+ blsp_uart4, blsp_uim4, qdss_stm16, qdss_stm15, blsp_i2c4,
+ qdss_stm14, dac_calib26, spkr_i2s, audio_ref, lpass_slimbus,
+ isense_dbg, tsense_pwm1, tsense_pwm2, btfm_slimbus, ter_mi2s,
+ qdss_stm22, qdss_stm21, qdss_stm20, qdss_stm19, gcc_gp1_clk_b,
+ sec_mi2s, blsp_spi5, blsp_uart5, blsp_uim5, gcc_gp2_clk_b,
+ gcc_gp3_clk_b, blsp_i2c5, blsp_spi12, blsp_uart12, blsp_uim12,
+ qdss_stm25, qdss_stm31, blsp_i2c12, qdss_stm30, qdss_stm29,
+ tsif1_clk, qdss_stm28, tsif1_en, tsif1_data, sdc4_cmd, qdss_stm27,
+ qdss_traceclk_b, tsif2_error, sdc43, vfr_1, qdss_stm26, tsif2_clk,
+ sdc4_clk, qdss_stm24, tsif2_en, sdc42, qdss_stm23, qdss_tracectl_b,
+ sd_card, tsif2_data, sdc41, tsif2_sync, sdc40, mdp_vsync_p_b,
+ ldo_en, mdp_vsync_s_b, ldo_update, blsp11_uart_tx_b, blsp11_uart_rx_b,
+ blsp11_i2c_sda_b, prng_rosc, blsp11_i2c_scl_b, uim2, uim1, uim_batt,
+ pci_e2, pa_indicator, adsp_ext, ddr_bist, qdss_tracedata_11,
+ qdss_tracedata_12, modem_tsync, nav_dr, nav_pps, pci_e1, gsm_tx,
+ qspi_cs, ssbi2, ssbi1, mss_lte, qspi_clk, qspi0, qspi1, qspi2, qspi3,
+ gpio
+
+- bias-disable:
+ Usage: optional
+ Value type: <none>
+ Definition: The specified pins should be configued as no pull.
+
+- bias-pull-down:
+ Usage: optional
+ Value type: <none>
+ Definition: The specified pins should be configued as pull down.
+
+- bias-pull-up:
+ Usage: optional
+ Value type: <none>
+ Definition: The specified pins should be configued as pull up.
+
+- output-high:
+ Usage: optional
+ Value type: <none>
+ Definition: The specified pins are configured in output mode, driven
+ high.
+ Not valid for sdc pins.
+
+- output-low:
+ Usage: optional
+ Value type: <none>
+ Definition: The specified pins are configured in output mode, driven
+ low.
+ Not valid for sdc pins.
+
+- drive-strength:
+ Usage: optional
+ Value type: <u32>
+ Definition: Selects the drive strength for the specified pins, in mA.
+ Valid values are: 2, 4, 6, 8, 10, 12, 14 and 16
+
+Example:
+
+ tlmm: pinctrl@01010000 {
+ compatible = "qcom,msm8996-pinctrl";
+ reg = <0x01010000 0x300000>;
+ interrupts = <0 208 0>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ uart_console_active: uart_console_active {
+ mux {
+ pins = "gpio4", "gpio5";
+ function = "blsp_uart8";
+ };
+
+ config {
+ pins = "gpio4", "gpio5";
+ drive-strength = <2>;
+ bias-disable;
+ };
+ };
+ };
git.samba.org / sfrench / cifs-2.6.git / blobdiff