drivers/tty/serial/stm32-usart.c

   1 // SPDX-License-Identifier: GPL-2.0
   2 /*
   3  * Copyright (C) Maxime Coquelin 2015
   4  * Copyright (C) STMicroelectronics SA 2017
   5  * Authors:  Maxime Coquelin <mcoquelin.stm32@gmail.com>
   6  *           Gerald Baeza <gerald.baeza@foss.st.com>
   7  *           Erwan Le Ray <erwan.leray@foss.st.com>
   8  *
   9  * Inspired by st-asc.c from STMicroelectronics (c)
  10  */
  11
  12 #include <linux/clk.h>
  13 #include <linux/console.h>
  14 #include <linux/delay.h>
  15 #include <linux/dma-direction.h>
  16 #include <linux/dmaengine.h>
  17 #include <linux/dma-mapping.h>
  18 #include <linux/io.h>
  19 #include <linux/iopoll.h>
  20 #include <linux/irq.h>
  21 #include <linux/module.h>
  22 #include <linux/of.h>
  23 #include <linux/of_platform.h>
  24 #include <linux/pinctrl/consumer.h>
  25 #include <linux/platform_device.h>
  26 #include <linux/pm_runtime.h>
  27 #include <linux/pm_wakeirq.h>
  28 #include <linux/serial_core.h>
  29 #include <linux/serial.h>
  30 #include <linux/spinlock.h>
  31 #include <linux/sysrq.h>
  32 #include <linux/tty_flip.h>
  33 #include <linux/tty.h>
  34
  35 #include "serial_mctrl_gpio.h"
  36 #include "stm32-usart.h"
  37
  38
  39 /* Register offsets */
  40 static struct stm32_usart_info __maybe_unused stm32f4_info = {
  41         .ofs = {
  42                 .isr    = 0x00,
  43                 .rdr    = 0x04,
  44                 .tdr    = 0x04,
  45                 .brr    = 0x08,
  46                 .cr1    = 0x0c,
  47                 .cr2    = 0x10,
  48                 .cr3    = 0x14,
  49                 .gtpr   = 0x18,
  50                 .rtor   = UNDEF_REG,
  51                 .rqr    = UNDEF_REG,
  52                 .icr    = UNDEF_REG,
  53         },
  54         .cfg = {
  55                 .uart_enable_bit = 13,
  56                 .has_7bits_data = false,
  57                 .fifosize = 1,
  58         }
  59 };
  60
  61 static struct stm32_usart_info __maybe_unused stm32f7_info = {
  62         .ofs = {
  63                 .cr1    = 0x00,
  64                 .cr2    = 0x04,
  65                 .cr3    = 0x08,
  66                 .brr    = 0x0c,
  67                 .gtpr   = 0x10,
  68                 .rtor   = 0x14,
  69                 .rqr    = 0x18,
  70                 .isr    = 0x1c,
  71                 .icr    = 0x20,
  72                 .rdr    = 0x24,
  73                 .tdr    = 0x28,
  74         },
  75         .cfg = {
  76                 .uart_enable_bit = 0,
  77                 .has_7bits_data = true,
  78                 .has_swap = true,
  79                 .fifosize = 1,
  80         }
  81 };
  82
  83 static struct stm32_usart_info __maybe_unused stm32h7_info = {
  84         .ofs = {
  85                 .cr1    = 0x00,
  86                 .cr2    = 0x04,
  87                 .cr3    = 0x08,
  88                 .brr    = 0x0c,
  89                 .gtpr   = 0x10,
  90                 .rtor   = 0x14,
  91                 .rqr    = 0x18,
  92                 .isr    = 0x1c,
  93                 .icr    = 0x20,
  94                 .rdr    = 0x24,
  95                 .tdr    = 0x28,
  96         },
  97         .cfg = {
  98                 .uart_enable_bit = 0,
  99                 .has_7bits_data = true,
 100                 .has_swap = true,
 101                 .has_wakeup = true,
 102                 .has_fifo = true,
 103                 .fifosize = 16,
 104         }
 105 };
 106
 107 static void stm32_usart_stop_tx(struct uart_port *port);
 108 static void stm32_usart_transmit_chars(struct uart_port *port);
 109 static void __maybe_unused stm32_usart_console_putchar(struct uart_port *port, unsigned char ch);
 110
 111 static inline struct stm32_port *to_stm32_port(struct uart_port *port)
 112 {
 113         return container_of(port, struct stm32_port, port);
 114 }
 115
 116 static void stm32_usart_set_bits(struct uart_port *port, u32 reg, u32 bits)
 117 {
 118         u32 val;
 119
 120         val = readl_relaxed(port->membase + reg);
 121         val |= bits;
 122         writel_relaxed(val, port->membase + reg);
 123 }
 124
 125 static void stm32_usart_clr_bits(struct uart_port *port, u32 reg, u32 bits)
 126 {
 127         u32 val;
 128
 129         val = readl_relaxed(port->membase + reg);
 130         val &= ~bits;
 131         writel_relaxed(val, port->membase + reg);
 132 }
 133
 134 static unsigned int stm32_usart_tx_empty(struct uart_port *port)
 135 {
 136         struct stm32_port *stm32_port = to_stm32_port(port);
 137         const struct stm32_usart_offsets *ofs = &stm32_port->info->ofs;
 138
 139         if (readl_relaxed(port->membase + ofs->isr) & USART_SR_TC)
 140                 return TIOCSER_TEMT;
 141
 142         return 0;
 143 }
 144
 145 static void stm32_usart_rs485_rts_enable(struct uart_port *port)
 146 {
 147         struct stm32_port *stm32_port = to_stm32_port(port);
 148         struct serial_rs485 *rs485conf = &port->rs485;
 149
 150         if (stm32_port->hw_flow_control ||
 151             !(rs485conf->flags & SER_RS485_ENABLED))
 152                 return;
 153
 154         if (rs485conf->flags & SER_RS485_RTS_ON_SEND) {
 155                 mctrl_gpio_set(stm32_port->gpios,
 156                                stm32_port->port.mctrl | TIOCM_RTS);
 157         } else {
 158                 mctrl_gpio_set(stm32_port->gpios,
 159                                stm32_port->port.mctrl & ~TIOCM_RTS);
 160         }
 161 }
 162
 163 static void stm32_usart_rs485_rts_disable(struct uart_port *port)
 164 {
 165         struct stm32_port *stm32_port = to_stm32_port(port);
 166         struct serial_rs485 *rs485conf = &port->rs485;
 167
 168         if (stm32_port->hw_flow_control ||
 169             !(rs485conf->flags & SER_RS485_ENABLED))
 170                 return;
 171
 172         if (rs485conf->flags & SER_RS485_RTS_ON_SEND) {
 173                 mctrl_gpio_set(stm32_port->gpios,
 174                                stm32_port->port.mctrl & ~TIOCM_RTS);
 175         } else {
 176                 mctrl_gpio_set(stm32_port->gpios,
 177                                stm32_port->port.mctrl | TIOCM_RTS);
 178         }
 179 }
 180
 181 static void stm32_usart_config_reg_rs485(u32 *cr1, u32 *cr3, u32 delay_ADE,
 182                                          u32 delay_DDE, u32 baud)
 183 {
 184         u32 rs485_deat_dedt;
 185         u32 rs485_deat_dedt_max = (USART_CR1_DEAT_MASK >> USART_CR1_DEAT_SHIFT);
 186         bool over8;
 187
 188         *cr3 |= USART_CR3_DEM;
 189         over8 = *cr1 & USART_CR1_OVER8;
 190
 191         *cr1 &= ~(USART_CR1_DEDT_MASK | USART_CR1_DEAT_MASK);
 192
 193         if (over8)
 194                 rs485_deat_dedt = delay_ADE * baud * 8;
 195         else
 196                 rs485_deat_dedt = delay_ADE * baud * 16;
 197
 198         rs485_deat_dedt = DIV_ROUND_CLOSEST(rs485_deat_dedt, 1000);
 199         rs485_deat_dedt = rs485_deat_dedt > rs485_deat_dedt_max ?
 200                           rs485_deat_dedt_max : rs485_deat_dedt;
 201         rs485_deat_dedt = (rs485_deat_dedt << USART_CR1_DEAT_SHIFT) &
 202                            USART_CR1_DEAT_MASK;
 203         *cr1 |= rs485_deat_dedt;
 204
 205         if (over8)
 206                 rs485_deat_dedt = delay_DDE * baud * 8;
 207         else
 208                 rs485_deat_dedt = delay_DDE * baud * 16;
 209
 210         rs485_deat_dedt = DIV_ROUND_CLOSEST(rs485_deat_dedt, 1000);
 211         rs485_deat_dedt = rs485_deat_dedt > rs485_deat_dedt_max ?
 212                           rs485_deat_dedt_max : rs485_deat_dedt;
 213         rs485_deat_dedt = (rs485_deat_dedt << USART_CR1_DEDT_SHIFT) &
 214                            USART_CR1_DEDT_MASK;
 215         *cr1 |= rs485_deat_dedt;
 216 }
 217
 218 static int stm32_usart_config_rs485(struct uart_port *port, struct ktermios *termios,
 219                                     struct serial_rs485 *rs485conf)
 220 {
 221         struct stm32_port *stm32_port = to_stm32_port(port);
 222         const struct stm32_usart_offsets *ofs = &stm32_port->info->ofs;
 223         const struct stm32_usart_config *cfg = &stm32_port->info->cfg;
 224         u32 usartdiv, baud, cr1, cr3;
 225         bool over8;
 226
 227         stm32_usart_clr_bits(port, ofs->cr1, BIT(cfg->uart_enable_bit));
 228
 229         if (rs485conf->flags & SER_RS485_ENABLED) {
 230                 cr1 = readl_relaxed(port->membase + ofs->cr1);
 231                 cr3 = readl_relaxed(port->membase + ofs->cr3);
 232                 usartdiv = readl_relaxed(port->membase + ofs->brr);
 233                 usartdiv = usartdiv & GENMASK(15, 0);
 234                 over8 = cr1 & USART_CR1_OVER8;
 235
 236                 if (over8)
 237                         usartdiv = usartdiv | (usartdiv & GENMASK(4, 0))
 238                                    << USART_BRR_04_R_SHIFT;
 239
 240                 baud = DIV_ROUND_CLOSEST(port->uartclk, usartdiv);
 241                 stm32_usart_config_reg_rs485(&cr1, &cr3,
 242                                              rs485conf->delay_rts_before_send,
 243                                              rs485conf->delay_rts_after_send,
 244                                              baud);
 245
 246                 if (rs485conf->flags & SER_RS485_RTS_ON_SEND)
 247                         cr3 &= ~USART_CR3_DEP;
 248                 else
 249                         cr3 |= USART_CR3_DEP;
 250
 251                 writel_relaxed(cr3, port->membase + ofs->cr3);
 252                 writel_relaxed(cr1, port->membase + ofs->cr1);
 253
 254                 rs485conf->flags |= SER_RS485_RX_DURING_TX;
 255         } else {
 256                 stm32_usart_clr_bits(port, ofs->cr3,
 257                                      USART_CR3_DEM | USART_CR3_DEP);
 258                 stm32_usart_clr_bits(port, ofs->cr1,
 259                                      USART_CR1_DEDT_MASK | USART_CR1_DEAT_MASK);
 260         }
 261
 262         stm32_usart_set_bits(port, ofs->cr1, BIT(cfg->uart_enable_bit));
 263
 264         /* Adjust RTS polarity in case it's driven in software */
 265         if (stm32_usart_tx_empty(port))
 266                 stm32_usart_rs485_rts_disable(port);
 267         else
 268                 stm32_usart_rs485_rts_enable(port);
 269
 270         return 0;
 271 }
 272
 273 static int stm32_usart_init_rs485(struct uart_port *port,
 274                                   struct platform_device *pdev)
 275 {
 276         struct serial_rs485 *rs485conf = &port->rs485;
 277
 278         rs485conf->flags = 0;
 279         rs485conf->delay_rts_before_send = 0;
 280         rs485conf->delay_rts_after_send = 0;
 281
 282         if (!pdev->dev.of_node)
 283                 return -ENODEV;
 284
 285         return uart_get_rs485_mode(port);
 286 }
 287
 288 static bool stm32_usart_rx_dma_started(struct stm32_port *stm32_port)
 289 {
 290         return stm32_port->rx_ch ? stm32_port->rx_dma_busy : false;
 291 }
 292
 293 static void stm32_usart_rx_dma_terminate(struct stm32_port *stm32_port)
 294 {
 295         dmaengine_terminate_async(stm32_port->rx_ch);
 296         stm32_port->rx_dma_busy = false;
 297 }
 298
 299 static int stm32_usart_dma_pause_resume(struct stm32_port *stm32_port,
 300                                         struct dma_chan *chan,
 301                                         enum dma_status expected_status,
 302                                         int dmaengine_pause_or_resume(struct dma_chan *),
 303                                         bool stm32_usart_xx_dma_started(struct stm32_port *),
 304                                         void stm32_usart_xx_dma_terminate(struct stm32_port *))
 305 {
 306         struct uart_port *port = &stm32_port->port;
 307         enum dma_status dma_status;
 308         int ret;
 309
 310         if (!stm32_usart_xx_dma_started(stm32_port))
 311                 return -EPERM;
 312
 313         dma_status = dmaengine_tx_status(chan, chan->cookie, NULL);
 314         if (dma_status != expected_status)
 315                 return -EAGAIN;
 316
 317         ret = dmaengine_pause_or_resume(chan);
 318         if (ret) {
 319                 dev_err(port->dev, "DMA failed with error code: %d\n", ret);
 320                 stm32_usart_xx_dma_terminate(stm32_port);
 321         }
 322         return ret;
 323 }
 324
 325 static int stm32_usart_rx_dma_pause(struct stm32_port *stm32_port)
 326 {
 327         return stm32_usart_dma_pause_resume(stm32_port, stm32_port->rx_ch,
 328                                             DMA_IN_PROGRESS, dmaengine_pause,
 329                                             stm32_usart_rx_dma_started,
 330                                             stm32_usart_rx_dma_terminate);
 331 }
 332
 333 static int stm32_usart_rx_dma_resume(struct stm32_port *stm32_port)
 334 {
 335         return stm32_usart_dma_pause_resume(stm32_port, stm32_port->rx_ch,
 336                                             DMA_PAUSED, dmaengine_resume,
 337                                             stm32_usart_rx_dma_started,
 338                                             stm32_usart_rx_dma_terminate);
 339 }
 340
 341 /* Return true when data is pending (in pio mode), and false when no data is pending. */
 342 static bool stm32_usart_pending_rx_pio(struct uart_port *port, u32 *sr)
 343 {
 344         struct stm32_port *stm32_port = to_stm32_port(port);
 345         const struct stm32_usart_offsets *ofs = &stm32_port->info->ofs;
 346
 347         *sr = readl_relaxed(port->membase + ofs->isr);
 348         /* Get pending characters in RDR or FIFO */
 349         if (*sr & USART_SR_RXNE) {
 350                 /* Get all pending characters from the RDR or the FIFO when using interrupts */
 351                 if (!stm32_usart_rx_dma_started(stm32_port))
 352                         return true;
 353
 354                 /* Handle only RX data errors when using DMA */
 355                 if (*sr & USART_SR_ERR_MASK)
 356                         return true;
 357         }
 358
 359         return false;
 360 }
 361
 362 static u8 stm32_usart_get_char_pio(struct uart_port *port)
 363 {
 364         struct stm32_port *stm32_port = to_stm32_port(port);
 365         const struct stm32_usart_offsets *ofs = &stm32_port->info->ofs;
 366         unsigned long c;
 367
 368         c = readl_relaxed(port->membase + ofs->rdr);
 369         /* Apply RDR data mask */
 370         c &= stm32_port->rdr_mask;
 371
 372         return c;
 373 }
 374
 375 static unsigned int stm32_usart_receive_chars_pio(struct uart_port *port)
 376 {
 377         struct stm32_port *stm32_port = to_stm32_port(port);
 378         const struct stm32_usart_offsets *ofs = &stm32_port->info->ofs;
 379         unsigned int size = 0;
 380         u32 sr;
 381         u8 c, flag;
 382
 383         while (stm32_usart_pending_rx_pio(port, &sr)) {
 384                 sr |= USART_SR_DUMMY_RX;
 385                 flag = TTY_NORMAL;
 386
 387                 /*
 388                  * Status bits has to be cleared before reading the RDR:
 389                  * In FIFO mode, reading the RDR will pop the next data
 390                  * (if any) along with its status bits into the SR.
 391                  * Not doing so leads to misalignement between RDR and SR,
 392                  * and clear status bits of the next rx data.
 393                  *
 394                  * Clear errors flags for stm32f7 and stm32h7 compatible
 395                  * devices. On stm32f4 compatible devices, the error bit is
 396                  * cleared by the sequence [read SR - read DR].
 397                  */
 398                 if ((sr & USART_SR_ERR_MASK) && ofs->icr != UNDEF_REG)
 399                         writel_relaxed(sr & USART_SR_ERR_MASK,
 400                                        port->membase + ofs->icr);
 401
 402                 c = stm32_usart_get_char_pio(port);
 403                 port->icount.rx++;
 404                 size++;
 405                 if (sr & USART_SR_ERR_MASK) {
 406                         if (sr & USART_SR_ORE) {
 407                                 port->icount.overrun++;
 408                         } else if (sr & USART_SR_PE) {
 409                                 port->icount.parity++;
 410                         } else if (sr & USART_SR_FE) {
 411                                 /* Break detection if character is null */
 412                                 if (!c) {
 413                                         port->icount.brk++;
 414                                         if (uart_handle_break(port))
 415                                                 continue;
 416                                 } else {
 417                                         port->icount.frame++;
 418                                 }
 419                         }
 420
 421                         sr &= port->read_status_mask;
 422
 423                         if (sr & USART_SR_PE) {
 424                                 flag = TTY_PARITY;
 425                         } else if (sr & USART_SR_FE) {
 426                                 if (!c)
 427                                         flag = TTY_BREAK;
 428                                 else
 429                                         flag = TTY_FRAME;
 430                         }
 431                 }
 432
 433                 if (uart_prepare_sysrq_char(port, c))
 434                         continue;
 435                 uart_insert_char(port, sr, USART_SR_ORE, c, flag);
 436         }
 437
 438         return size;
 439 }
 440
 441 static void stm32_usart_push_buffer_dma(struct uart_port *port, unsigned int dma_size)
 442 {
 443         struct stm32_port *stm32_port = to_stm32_port(port);
 444         struct tty_port *ttyport = &stm32_port->port.state->port;
 445         unsigned char *dma_start;
 446         int dma_count, i;
 447
 448         dma_start = stm32_port->rx_buf + (RX_BUF_L - stm32_port->last_res);
 449
 450         /*
 451          * Apply rdr_mask on buffer in order to mask parity bit.
 452          * This loop is useless in cs8 mode because DMA copies only
 453          * 8 bits and already ignores parity bit.
 454          */
 455         if (!(stm32_port->rdr_mask == (BIT(8) - 1)))
 456                 for (i = 0; i < dma_size; i++)
 457                         *(dma_start + i) &= stm32_port->rdr_mask;
 458
 459         dma_count = tty_insert_flip_string(ttyport, dma_start, dma_size);
 460         port->icount.rx += dma_count;
 461         if (dma_count != dma_size)
 462                 port->icount.buf_overrun++;
 463         stm32_port->last_res -= dma_count;
 464         if (stm32_port->last_res == 0)
 465                 stm32_port->last_res = RX_BUF_L;
 466 }
 467
 468 static unsigned int stm32_usart_receive_chars_dma(struct uart_port *port)
 469 {
 470         struct stm32_port *stm32_port = to_stm32_port(port);
 471         unsigned int dma_size, size = 0;
 472
 473         /* DMA buffer is configured in cyclic mode and handles the rollback of the buffer. */
 474         if (stm32_port->rx_dma_state.residue > stm32_port->last_res) {
 475                 /* Conditional first part: from last_res to end of DMA buffer */
 476                 dma_size = stm32_port->last_res;
 477                 stm32_usart_push_buffer_dma(port, dma_size);
 478                 size = dma_size;
 479         }
 480
 481         dma_size = stm32_port->last_res - stm32_port->rx_dma_state.residue;
 482         stm32_usart_push_buffer_dma(port, dma_size);
 483         size += dma_size;
 484
 485         return size;
 486 }
 487
 488 static unsigned int stm32_usart_receive_chars(struct uart_port *port, bool force_dma_flush)
 489 {
 490         struct stm32_port *stm32_port = to_stm32_port(port);
 491         const struct stm32_usart_offsets *ofs = &stm32_port->info->ofs;
 492         enum dma_status rx_dma_status;
 493         u32 sr;
 494         unsigned int size = 0;
 495
 496         if (stm32_usart_rx_dma_started(stm32_port) || force_dma_flush) {
 497                 rx_dma_status = dmaengine_tx_status(stm32_port->rx_ch,
 498                                                     stm32_port->rx_ch->cookie,
 499                                                     &stm32_port->rx_dma_state);
 500                 if (rx_dma_status == DMA_IN_PROGRESS ||
 501                     rx_dma_status == DMA_PAUSED) {
 502                         /* Empty DMA buffer */
 503                         size = stm32_usart_receive_chars_dma(port);
 504                         sr = readl_relaxed(port->membase + ofs->isr);
 505                         if (sr & USART_SR_ERR_MASK) {
 506                                 /* Disable DMA request line */
 507                                 stm32_usart_clr_bits(port, ofs->cr3, USART_CR3_DMAR);
 508
 509                                 /* Switch to PIO mode to handle the errors */
 510                                 size += stm32_usart_receive_chars_pio(port);
 511
 512                                 /* Switch back to DMA mode */
 513                                 stm32_usart_set_bits(port, ofs->cr3, USART_CR3_DMAR);
 514                         }
 515                 } else {
 516                         /* Disable RX DMA */
 517                         stm32_usart_rx_dma_terminate(stm32_port);
 518                         /* Fall back to interrupt mode */
 519                         dev_dbg(port->dev, "DMA error, fallback to irq mode\n");
 520                         size = stm32_usart_receive_chars_pio(port);
 521                 }
 522         } else {
 523                 size = stm32_usart_receive_chars_pio(port);
 524         }
 525
 526         return size;
 527 }
 528
 529 static void stm32_usart_rx_dma_complete(void *arg)
 530 {
 531         struct uart_port *port = arg;
 532         struct tty_port *tport = &port->state->port;
 533         unsigned int size;
 534         unsigned long flags;
 535
 536         uart_port_lock_irqsave(port, &flags);
 537         size = stm32_usart_receive_chars(port, false);
 538         uart_unlock_and_check_sysrq_irqrestore(port, flags);
 539         if (size)
 540                 tty_flip_buffer_push(tport);
 541 }
 542
 543 static int stm32_usart_rx_dma_start_or_resume(struct uart_port *port)
 544 {
 545         struct stm32_port *stm32_port = to_stm32_port(port);
 546         struct dma_async_tx_descriptor *desc;
 547         enum dma_status rx_dma_status;
 548         int ret;
 549
 550         if (stm32_port->throttled)
 551                 return 0;
 552
 553         if (stm32_port->rx_dma_busy) {
 554                 rx_dma_status = dmaengine_tx_status(stm32_port->rx_ch,
 555                                                     stm32_port->rx_ch->cookie,
 556                                                     NULL);
 557                 if (rx_dma_status == DMA_IN_PROGRESS)
 558                         return 0;
 559
 560                 if (rx_dma_status == DMA_PAUSED && !stm32_usart_rx_dma_resume(stm32_port))
 561                         return 0;
 562
 563                 dev_err(port->dev, "DMA failed : status error.\n");
 564                 stm32_usart_rx_dma_terminate(stm32_port);
 565         }
 566
 567         stm32_port->rx_dma_busy = true;
 568
 569         stm32_port->last_res = RX_BUF_L;
 570         /* Prepare a DMA cyclic transaction */
 571         desc = dmaengine_prep_dma_cyclic(stm32_port->rx_ch,
 572                                          stm32_port->rx_dma_buf,
 573                                          RX_BUF_L, RX_BUF_P,
 574                                          DMA_DEV_TO_MEM,
 575                                          DMA_PREP_INTERRUPT);
 576         if (!desc) {
 577                 dev_err(port->dev, "rx dma prep cyclic failed\n");
 578                 stm32_port->rx_dma_busy = false;
 579                 return -ENODEV;
 580         }
 581
 582         desc->callback = stm32_usart_rx_dma_complete;
 583         desc->callback_param = port;
 584
 585         /* Push current DMA transaction in the pending queue */
 586         ret = dma_submit_error(dmaengine_submit(desc));
 587         if (ret) {
 588                 dmaengine_terminate_sync(stm32_port->rx_ch);
 589                 stm32_port->rx_dma_busy = false;
 590                 return ret;
 591         }
 592
 593         /* Issue pending DMA requests */
 594         dma_async_issue_pending(stm32_port->rx_ch);
 595
 596         return 0;
 597 }
 598
 599 static void stm32_usart_tx_dma_terminate(struct stm32_port *stm32_port)
 600 {
 601         dmaengine_terminate_async(stm32_port->tx_ch);
 602         stm32_port->tx_dma_busy = false;
 603 }
 604
 605 static bool stm32_usart_tx_dma_started(struct stm32_port *stm32_port)
 606 {
 607         /*
 608          * We cannot use the function "dmaengine_tx_status" to know the
 609          * status of DMA. This function does not show if the "dma complete"
 610          * callback of the DMA transaction has been called. So we prefer
 611          * to use "tx_dma_busy" flag to prevent dual DMA transaction at the
 612          * same time.
 613          */
 614         return stm32_port->tx_dma_busy;
 615 }
 616
 617 static int stm32_usart_tx_dma_pause(struct stm32_port *stm32_port)
 618 {
 619         return stm32_usart_dma_pause_resume(stm32_port, stm32_port->tx_ch,
 620                                             DMA_IN_PROGRESS, dmaengine_pause,
 621                                             stm32_usart_tx_dma_started,
 622                                             stm32_usart_tx_dma_terminate);
 623 }
 624
 625 static int stm32_usart_tx_dma_resume(struct stm32_port *stm32_port)
 626 {
 627         return stm32_usart_dma_pause_resume(stm32_port, stm32_port->tx_ch,
 628                                             DMA_PAUSED, dmaengine_resume,
 629                                             stm32_usart_tx_dma_started,
 630                                             stm32_usart_tx_dma_terminate);
 631 }
 632
 633 static void stm32_usart_tx_dma_complete(void *arg)
 634 {
 635         struct uart_port *port = arg;
 636         struct stm32_port *stm32port = to_stm32_port(port);
 637         unsigned long flags;
 638
 639         stm32_usart_tx_dma_terminate(stm32port);
 640
 641         /* Let's see if we have pending data to send */
 642         uart_port_lock_irqsave(port, &flags);
 643         stm32_usart_transmit_chars(port);
 644         uart_port_unlock_irqrestore(port, flags);
 645 }
 646
 647 static void stm32_usart_tx_interrupt_enable(struct uart_port *port)
 648 {
 649         struct stm32_port *stm32_port = to_stm32_port(port);
 650         const struct stm32_usart_offsets *ofs = &stm32_port->info->ofs;
 651
 652         /*
 653          * Enables TX FIFO threashold irq when FIFO is enabled,
 654          * or TX empty irq when FIFO is disabled
 655          */
 656         if (stm32_port->fifoen && stm32_port->txftcfg >= 0)
 657                 stm32_usart_set_bits(port, ofs->cr3, USART_CR3_TXFTIE);
 658         else
 659                 stm32_usart_set_bits(port, ofs->cr1, USART_CR1_TXEIE);
 660 }
 661
 662 static void stm32_usart_tc_interrupt_enable(struct uart_port *port)
 663 {
 664         struct stm32_port *stm32_port = to_stm32_port(port);
 665         const struct stm32_usart_offsets *ofs = &stm32_port->info->ofs;
 666
 667         stm32_usart_set_bits(port, ofs->cr1, USART_CR1_TCIE);
 668 }
 669
 670 static void stm32_usart_tx_interrupt_disable(struct uart_port *port)
 671 {
 672         struct stm32_port *stm32_port = to_stm32_port(port);
 673         const struct stm32_usart_offsets *ofs = &stm32_port->info->ofs;
 674
 675         if (stm32_port->fifoen && stm32_port->txftcfg >= 0)
 676                 stm32_usart_clr_bits(port, ofs->cr3, USART_CR3_TXFTIE);
 677         else
 678                 stm32_usart_clr_bits(port, ofs->cr1, USART_CR1_TXEIE);
 679 }
 680
 681 static void stm32_usart_tc_interrupt_disable(struct uart_port *port)
 682 {
 683         struct stm32_port *stm32_port = to_stm32_port(port);
 684         const struct stm32_usart_offsets *ofs = &stm32_port->info->ofs;
 685
 686         stm32_usart_clr_bits(port, ofs->cr1, USART_CR1_TCIE);
 687 }
 688
 689 static void stm32_usart_transmit_chars_pio(struct uart_port *port)
 690 {
 691         struct stm32_port *stm32_port = to_stm32_port(port);
 692         const struct stm32_usart_offsets *ofs = &stm32_port->info->ofs;
 693         struct circ_buf *xmit = &port->state->xmit;
 694
 695         while (!uart_circ_empty(xmit)) {
 696                 /* Check that TDR is empty before filling FIFO */
 697                 if (!(readl_relaxed(port->membase + ofs->isr) & USART_SR_TXE))
 698                         break;
 699                 writel_relaxed(xmit->buf[xmit->tail], port->membase + ofs->tdr);
 700                 uart_xmit_advance(port, 1);
 701         }
 702
 703         /* rely on TXE irq (mask or unmask) for sending remaining data */
 704         if (uart_circ_empty(xmit))
 705                 stm32_usart_tx_interrupt_disable(port);
 706         else
 707                 stm32_usart_tx_interrupt_enable(port);
 708 }
 709
 710 static void stm32_usart_transmit_chars_dma(struct uart_port *port)
 711 {
 712         struct stm32_port *stm32port = to_stm32_port(port);
 713         struct circ_buf *xmit = &port->state->xmit;
 714         struct dma_async_tx_descriptor *desc = NULL;
 715         unsigned int count;
 716         int ret;
 717
 718         if (stm32_usart_tx_dma_started(stm32port)) {
 719                 ret = stm32_usart_tx_dma_resume(stm32port);
 720                 if (ret < 0 && ret != -EAGAIN)
 721                         goto fallback_err;
 722                 return;
 723         }
 724
 725         count = uart_circ_chars_pending(xmit);
 726
 727         if (count > TX_BUF_L)
 728                 count = TX_BUF_L;
 729
 730         if (xmit->tail < xmit->head) {
 731                 memcpy(&stm32port->tx_buf[0], &xmit->buf[xmit->tail], count);
 732         } else {
 733                 size_t one = UART_XMIT_SIZE - xmit->tail;
 734                 size_t two;
 735
 736                 if (one > count)
 737                         one = count;
 738                 two = count - one;
 739
 740                 memcpy(&stm32port->tx_buf[0], &xmit->buf[xmit->tail], one);
 741                 if (two)
 742                         memcpy(&stm32port->tx_buf[one], &xmit->buf[0], two);
 743         }
 744
 745         desc = dmaengine_prep_slave_single(stm32port->tx_ch,
 746                                            stm32port->tx_dma_buf,
 747                                            count,
 748                                            DMA_MEM_TO_DEV,
 749                                            DMA_PREP_INTERRUPT);
 750
 751         if (!desc)
 752                 goto fallback_err;
 753
 754         /*
 755          * Set "tx_dma_busy" flag. This flag will be released when
 756          * dmaengine_terminate_async will be called. This flag helps
 757          * transmit_chars_dma not to start another DMA transaction
 758          * if the callback of the previous is not yet called.
 759          */
 760         stm32port->tx_dma_busy = true;
 761
 762         desc->callback = stm32_usart_tx_dma_complete;
 763         desc->callback_param = port;
 764
 765         /* Push current DMA TX transaction in the pending queue */
 766         /* DMA no yet started, safe to free resources */
 767         ret = dma_submit_error(dmaengine_submit(desc));
 768         if (ret) {
 769                 dev_err(port->dev, "DMA failed with error code: %d\n", ret);
 770                 stm32_usart_tx_dma_terminate(stm32port);
 771                 goto fallback_err;
 772         }
 773
 774         /* Issue pending DMA TX requests */
 775         dma_async_issue_pending(stm32port->tx_ch);
 776
 777         uart_xmit_advance(port, count);
 778
 779         return;
 780
 781 fallback_err:
 782         stm32_usart_transmit_chars_pio(port);
 783 }
 784
 785 static void stm32_usart_transmit_chars(struct uart_port *port)
 786 {
 787         struct stm32_port *stm32_port = to_stm32_port(port);
 788         const struct stm32_usart_offsets *ofs = &stm32_port->info->ofs;
 789         struct circ_buf *xmit = &port->state->xmit;
 790         u32 isr;
 791         int ret;
 792
 793         if (!stm32_port->hw_flow_control &&
 794             port->rs485.flags & SER_RS485_ENABLED &&
 795             (port->x_char ||
 796              !(uart_circ_empty(xmit) || uart_tx_stopped(port)))) {
 797                 stm32_usart_tc_interrupt_disable(port);
 798                 stm32_usart_rs485_rts_enable(port);
 799         }
 800
 801         if (port->x_char) {
 802                 /* dma terminate may have been called in case of dma pause failure */
 803                 stm32_usart_tx_dma_pause(stm32_port);
 804
 805                 /* Check that TDR is empty before filling FIFO */
 806                 ret =
 807                 readl_relaxed_poll_timeout_atomic(port->membase + ofs->isr,
 808                                                   isr,
 809                                                   (isr & USART_SR_TXE),
 810                                                   10, 1000);
 811                 if (ret)
 812                         dev_warn(port->dev, "1 character may be erased\n");
 813
 814                 writel_relaxed(port->x_char, port->membase + ofs->tdr);
 815                 port->x_char = 0;
 816                 port->icount.tx++;
 817
 818                 /* dma terminate may have been called in case of dma resume failure */
 819                 stm32_usart_tx_dma_resume(stm32_port);
 820                 return;
 821         }
 822
 823         if (uart_circ_empty(xmit) || uart_tx_stopped(port)) {
 824                 stm32_usart_tx_interrupt_disable(port);
 825                 return;
 826         }
 827
 828         if (ofs->icr == UNDEF_REG)
 829                 stm32_usart_clr_bits(port, ofs->isr, USART_SR_TC);
 830         else
 831                 writel_relaxed(USART_ICR_TCCF, port->membase + ofs->icr);
 832
 833         if (stm32_port->tx_ch)
 834                 stm32_usart_transmit_chars_dma(port);
 835         else
 836                 stm32_usart_transmit_chars_pio(port);
 837
 838         if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
 839                 uart_write_wakeup(port);
 840
 841         if (uart_circ_empty(xmit)) {
 842                 stm32_usart_tx_interrupt_disable(port);
 843                 if (!stm32_port->hw_flow_control &&
 844                     port->rs485.flags & SER_RS485_ENABLED) {
 845                         stm32_usart_tc_interrupt_enable(port);
 846                 }
 847         }
 848 }
 849
 850 static irqreturn_t stm32_usart_interrupt(int irq, void *ptr)
 851 {
 852         struct uart_port *port = ptr;
 853         struct tty_port *tport = &port->state->port;
 854         struct stm32_port *stm32_port = to_stm32_port(port);
 855         const struct stm32_usart_offsets *ofs = &stm32_port->info->ofs;
 856         u32 sr;
 857         unsigned int size;
 858
 859         sr = readl_relaxed(port->membase + ofs->isr);
 860
 861         if (!stm32_port->hw_flow_control &&
 862             port->rs485.flags & SER_RS485_ENABLED &&
 863             (sr & USART_SR_TC)) {
 864                 stm32_usart_tc_interrupt_disable(port);
 865                 stm32_usart_rs485_rts_disable(port);
 866         }
 867
 868         if ((sr & USART_SR_RTOF) && ofs->icr != UNDEF_REG)
 869                 writel_relaxed(USART_ICR_RTOCF,
 870                                port->membase + ofs->icr);
 871
 872         if ((sr & USART_SR_WUF) && ofs->icr != UNDEF_REG) {
 873                 /* Clear wake up flag and disable wake up interrupt */
 874                 writel_relaxed(USART_ICR_WUCF,
 875                                port->membase + ofs->icr);
 876                 stm32_usart_clr_bits(port, ofs->cr3, USART_CR3_WUFIE);
 877                 if (irqd_is_wakeup_set(irq_get_irq_data(port->irq)))
 878                         pm_wakeup_event(tport->tty->dev, 0);
 879         }
 880
 881         /*
 882          * rx errors in dma mode has to be handled ASAP to avoid overrun as the DMA request
 883          * line has been masked by HW and rx data are stacking in FIFO.
 884          */
 885         if (!stm32_port->throttled) {
 886                 if (((sr & USART_SR_RXNE) && !stm32_usart_rx_dma_started(stm32_port)) ||
 887                     ((sr & USART_SR_ERR_MASK) && stm32_usart_rx_dma_started(stm32_port))) {
 888                         uart_port_lock(port);
 889                         size = stm32_usart_receive_chars(port, false);
 890                         uart_unlock_and_check_sysrq(port);
 891                         if (size)
 892                                 tty_flip_buffer_push(tport);
 893                 }
 894         }
 895
 896         if ((sr & USART_SR_TXE) && !(stm32_port->tx_ch)) {
 897                 uart_port_lock(port);
 898                 stm32_usart_transmit_chars(port);
 899                 uart_port_unlock(port);
 900         }
 901
 902         /* Receiver timeout irq for DMA RX */
 903         if (stm32_usart_rx_dma_started(stm32_port) && !stm32_port->throttled) {
 904                 uart_port_lock(port);
 905                 size = stm32_usart_receive_chars(port, false);
 906                 uart_unlock_and_check_sysrq(port);
 907                 if (size)
 908                         tty_flip_buffer_push(tport);
 909         }
 910
 911         return IRQ_HANDLED;
 912 }
 913
 914 static void stm32_usart_set_mctrl(struct uart_port *port, unsigned int mctrl)
 915 {
 916         struct stm32_port *stm32_port = to_stm32_port(port);
 917         const struct stm32_usart_offsets *ofs = &stm32_port->info->ofs;
 918
 919         if ((mctrl & TIOCM_RTS) && (port->status & UPSTAT_AUTORTS))
 920                 stm32_usart_set_bits(port, ofs->cr3, USART_CR3_RTSE);
 921         else
 922                 stm32_usart_clr_bits(port, ofs->cr3, USART_CR3_RTSE);
 923
 924         mctrl_gpio_set(stm32_port->gpios, mctrl);
 925 }
 926
 927 static unsigned int stm32_usart_get_mctrl(struct uart_port *port)
 928 {
 929         struct stm32_port *stm32_port = to_stm32_port(port);
 930         unsigned int ret;
 931
 932         /* This routine is used to get signals of: DCD, DSR, RI, and CTS */
 933         ret = TIOCM_CAR | TIOCM_DSR | TIOCM_CTS;
 934
 935         return mctrl_gpio_get(stm32_port->gpios, &ret);
 936 }
 937
 938 static void stm32_usart_enable_ms(struct uart_port *port)
 939 {
 940         mctrl_gpio_enable_ms(to_stm32_port(port)->gpios);
 941 }
 942
 943 static void stm32_usart_disable_ms(struct uart_port *port)
 944 {
 945         mctrl_gpio_disable_ms(to_stm32_port(port)->gpios);
 946 }
 947
 948 /* Transmit stop */
 949 static void stm32_usart_stop_tx(struct uart_port *port)
 950 {
 951         struct stm32_port *stm32_port = to_stm32_port(port);
 952
 953         stm32_usart_tx_interrupt_disable(port);
 954
 955         /* dma terminate may have been called in case of dma pause failure */
 956         stm32_usart_tx_dma_pause(stm32_port);
 957
 958         stm32_usart_rs485_rts_disable(port);
 959 }
 960
 961 /* There are probably characters waiting to be transmitted. */
 962 static void stm32_usart_start_tx(struct uart_port *port)
 963 {
 964         struct circ_buf *xmit = &port->state->xmit;
 965
 966         if (uart_circ_empty(xmit) && !port->x_char) {
 967                 stm32_usart_rs485_rts_disable(port);
 968                 return;
 969         }
 970
 971         stm32_usart_rs485_rts_enable(port);
 972
 973         stm32_usart_transmit_chars(port);
 974 }
 975
 976 /* Flush the transmit buffer. */
 977 static void stm32_usart_flush_buffer(struct uart_port *port)
 978 {
 979         struct stm32_port *stm32_port = to_stm32_port(port);
 980
 981         if (stm32_port->tx_ch)
 982                 stm32_usart_tx_dma_terminate(stm32_port);
 983 }
 984
 985 /* Throttle the remote when input buffer is about to overflow. */
 986 static void stm32_usart_throttle(struct uart_port *port)
 987 {
 988         struct stm32_port *stm32_port = to_stm32_port(port);
 989         const struct stm32_usart_offsets *ofs = &stm32_port->info->ofs;
 990         unsigned long flags;
 991
 992         uart_port_lock_irqsave(port, &flags);
 993
 994         /*
 995          * Pause DMA transfer, so the RX data gets queued into the FIFO.
 996          * Hardware flow control is triggered when RX FIFO is full.
 997          */
 998         stm32_usart_rx_dma_pause(stm32_port);
 999
1000         stm32_usart_clr_bits(port, ofs->cr1, stm32_port->cr1_irq);
1001         if (stm32_port->cr3_irq)
1002                 stm32_usart_clr_bits(port, ofs->cr3, stm32_port->cr3_irq);
1003
1004         stm32_port->throttled = true;
1005         uart_port_unlock_irqrestore(port, flags);
1006 }
1007
1008 /* Unthrottle the remote, the input buffer can now accept data. */
1009 static void stm32_usart_unthrottle(struct uart_port *port)
1010 {
1011         struct stm32_port *stm32_port = to_stm32_port(port);
1012         const struct stm32_usart_offsets *ofs = &stm32_port->info->ofs;
1013         unsigned long flags;
1014
1015         uart_port_lock_irqsave(port, &flags);
1016         stm32_usart_set_bits(port, ofs->cr1, stm32_port->cr1_irq);
1017         if (stm32_port->cr3_irq)
1018                 stm32_usart_set_bits(port, ofs->cr3, stm32_port->cr3_irq);
1019
1020         stm32_port->throttled = false;
1021
1022         /*
1023          * Switch back to DMA mode (resume DMA).
1024          * Hardware flow control is stopped when FIFO is not full any more.
1025          */
1026         if (stm32_port->rx_ch)
1027                 stm32_usart_rx_dma_start_or_resume(port);
1028
1029         uart_port_unlock_irqrestore(port, flags);
1030 }
1031
1032 /* Receive stop */
1033 static void stm32_usart_stop_rx(struct uart_port *port)
1034 {
1035         struct stm32_port *stm32_port = to_stm32_port(port);
1036         const struct stm32_usart_offsets *ofs = &stm32_port->info->ofs;
1037
1038         /* Disable DMA request line. */
1039         stm32_usart_rx_dma_pause(stm32_port);
1040
1041         stm32_usart_clr_bits(port, ofs->cr1, stm32_port->cr1_irq);
1042         if (stm32_port->cr3_irq)
1043                 stm32_usart_clr_bits(port, ofs->cr3, stm32_port->cr3_irq);
1044 }
1045
1046 static void stm32_usart_break_ctl(struct uart_port *port, int break_state)
1047 {
1048         struct stm32_port *stm32_port = to_stm32_port(port);
1049         const struct stm32_usart_offsets *ofs = &stm32_port->info->ofs;
1050         unsigned long flags;
1051
1052         spin_lock_irqsave(&port->lock, flags);
1053
1054         if (break_state)
1055                 stm32_usart_set_bits(port, ofs->rqr, USART_RQR_SBKRQ);
1056         else
1057                 stm32_usart_clr_bits(port, ofs->rqr, USART_RQR_SBKRQ);
1058
1059         spin_unlock_irqrestore(&port->lock, flags);
1060 }
1061
1062 static int stm32_usart_startup(struct uart_port *port)
1063 {
1064         struct stm32_port *stm32_port = to_stm32_port(port);
1065         const struct stm32_usart_offsets *ofs = &stm32_port->info->ofs;
1066         const struct stm32_usart_config *cfg = &stm32_port->info->cfg;
1067         const char *name = to_platform_device(port->dev)->name;
1068         u32 val;
1069         int ret;
1070
1071         ret = request_irq(port->irq, stm32_usart_interrupt,
1072                           IRQF_NO_SUSPEND, name, port);
1073         if (ret)
1074                 return ret;
1075
1076         if (stm32_port->swap) {
1077                 val = readl_relaxed(port->membase + ofs->cr2);
1078                 val |= USART_CR2_SWAP;
1079                 writel_relaxed(val, port->membase + ofs->cr2);
1080         }
1081
1082         /* RX FIFO Flush */
1083         if (ofs->rqr != UNDEF_REG)
1084                 writel_relaxed(USART_RQR_RXFRQ, port->membase + ofs->rqr);
1085
1086         if (stm32_port->rx_ch) {
1087                 ret = stm32_usart_rx_dma_start_or_resume(port);
1088                 if (ret) {
1089                         free_irq(port->irq, port);
1090                         return ret;
1091                 }
1092         }
1093
1094         /* RX enabling */
1095         val = stm32_port->cr1_irq | USART_CR1_RE | BIT(cfg->uart_enable_bit);
1096         stm32_usart_set_bits(port, ofs->cr1, val);
1097
1098         return 0;
1099 }
1100
1101 static void stm32_usart_shutdown(struct uart_port *port)
1102 {
1103         struct stm32_port *stm32_port = to_stm32_port(port);
1104         const struct stm32_usart_offsets *ofs = &stm32_port->info->ofs;
1105         const struct stm32_usart_config *cfg = &stm32_port->info->cfg;
1106         u32 val, isr;
1107         int ret;
1108
1109         if (stm32_usart_tx_dma_started(stm32_port))
1110                 stm32_usart_tx_dma_terminate(stm32_port);
1111
1112         if (stm32_port->tx_ch)
1113                 stm32_usart_clr_bits(port, ofs->cr3, USART_CR3_DMAT);
1114
1115         /* Disable modem control interrupts */
1116         stm32_usart_disable_ms(port);
1117
1118         val = USART_CR1_TXEIE | USART_CR1_TE;
1119         val |= stm32_port->cr1_irq | USART_CR1_RE;
1120         val |= BIT(cfg->uart_enable_bit);
1121         if (stm32_port->fifoen)
1122                 val |= USART_CR1_FIFOEN;
1123
1124         ret = readl_relaxed_poll_timeout(port->membase + ofs->isr,
1125                                          isr, (isr & USART_SR_TC),
1126                                          10, 100000);
1127
1128         /* Send the TC error message only when ISR_TC is not set */
1129         if (ret)
1130                 dev_err(port->dev, "Transmission is not complete\n");
1131
1132         /* Disable RX DMA. */
1133         if (stm32_port->rx_ch) {
1134                 stm32_usart_rx_dma_terminate(stm32_port);
1135                 dmaengine_synchronize(stm32_port->rx_ch);
1136         }
1137
1138         /* flush RX & TX FIFO */
1139         if (ofs->rqr != UNDEF_REG)
1140                 writel_relaxed(USART_RQR_TXFRQ | USART_RQR_RXFRQ,
1141                                port->membase + ofs->rqr);
1142
1143         stm32_usart_clr_bits(port, ofs->cr1, val);
1144
1145         free_irq(port->irq, port);
1146 }
1147
1148 static void stm32_usart_set_termios(struct uart_port *port,
1149                                     struct ktermios *termios,
1150                                     const struct ktermios *old)
1151 {
1152         struct stm32_port *stm32_port = to_stm32_port(port);
1153         const struct stm32_usart_offsets *ofs = &stm32_port->info->ofs;
1154         const struct stm32_usart_config *cfg = &stm32_port->info->cfg;
1155         struct serial_rs485 *rs485conf = &port->rs485;
1156         unsigned int baud, bits;
1157         u32 usartdiv, mantissa, fraction, oversampling;
1158         tcflag_t cflag = termios->c_cflag;
1159         u32 cr1, cr2, cr3, isr;
1160         unsigned long flags;
1161         int ret;
1162
1163         if (!stm32_port->hw_flow_control)
1164                 cflag &= ~CRTSCTS;
1165
1166         baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk / 8);
1167
1168         uart_port_lock_irqsave(port, &flags);
1169
1170         ret = readl_relaxed_poll_timeout_atomic(port->membase + ofs->isr,
1171                                                 isr,
1172                                                 (isr & USART_SR_TC),
1173                                                 10, 100000);
1174
1175         /* Send the TC error message only when ISR_TC is not set. */
1176         if (ret)
1177                 dev_err(port->dev, "Transmission is not complete\n");
1178
1179         /* Stop serial port and reset value */
1180         writel_relaxed(0, port->membase + ofs->cr1);
1181
1182         /* flush RX & TX FIFO */
1183         if (ofs->rqr != UNDEF_REG)
1184                 writel_relaxed(USART_RQR_TXFRQ | USART_RQR_RXFRQ,
1185                                port->membase + ofs->rqr);
1186
1187         cr1 = USART_CR1_TE | USART_CR1_RE;
1188         if (stm32_port->fifoen)
1189                 cr1 |= USART_CR1_FIFOEN;
1190         cr2 = stm32_port->swap ? USART_CR2_SWAP : 0;
1191
1192         /* Tx and RX FIFO configuration */
1193         cr3 = readl_relaxed(port->membase + ofs->cr3);
1194         cr3 &= USART_CR3_TXFTIE | USART_CR3_RXFTIE;
1195         if (stm32_port->fifoen) {
1196                 if (stm32_port->txftcfg >= 0)
1197                         cr3 |= stm32_port->txftcfg << USART_CR3_TXFTCFG_SHIFT;
1198                 if (stm32_port->rxftcfg >= 0)
1199                         cr3 |= stm32_port->rxftcfg << USART_CR3_RXFTCFG_SHIFT;
1200         }
1201
1202         if (cflag & CSTOPB)
1203                 cr2 |= USART_CR2_STOP_2B;
1204
1205         bits = tty_get_char_size(cflag);
1206         stm32_port->rdr_mask = (BIT(bits) - 1);
1207
1208         if (cflag & PARENB) {
1209                 bits++;
1210                 cr1 |= USART_CR1_PCE;
1211         }
1212
1213         /*
1214          * Word length configuration:
1215          * CS8 + parity, 9 bits word aka [M1:M0] = 0b01
1216          * CS7 or (CS6 + parity), 7 bits word aka [M1:M0] = 0b10
1217          * CS8 or (CS7 + parity), 8 bits word aka [M1:M0] = 0b00
1218          * M0 and M1 already cleared by cr1 initialization.
1219          */
1220         if (bits == 9) {
1221                 cr1 |= USART_CR1_M0;
1222         } else if ((bits == 7) && cfg->has_7bits_data) {
1223                 cr1 |= USART_CR1_M1;
1224         } else if (bits != 8) {
1225                 dev_dbg(port->dev, "Unsupported data bits config: %u bits\n"
1226                         , bits);
1227                 cflag &= ~CSIZE;
1228                 cflag |= CS8;
1229                 termios->c_cflag = cflag;
1230                 bits = 8;
1231                 if (cflag & PARENB) {
1232                         bits++;
1233                         cr1 |= USART_CR1_M0;
1234                 }
1235         }
1236
1237         if (ofs->rtor != UNDEF_REG && (stm32_port->rx_ch ||
1238                                        (stm32_port->fifoen &&
1239                                         stm32_port->rxftcfg >= 0))) {
1240                 if (cflag & CSTOPB)
1241                         bits = bits + 3; /* 1 start bit + 2 stop bits */
1242                 else
1243                         bits = bits + 2; /* 1 start bit + 1 stop bit */
1244
1245                 /* RX timeout irq to occur after last stop bit + bits */
1246                 stm32_port->cr1_irq = USART_CR1_RTOIE;
1247                 writel_relaxed(bits, port->membase + ofs->rtor);
1248                 cr2 |= USART_CR2_RTOEN;
1249                 /*
1250                  * Enable fifo threshold irq in two cases, either when there is no DMA, or when
1251                  * wake up over usart, from low power until the DMA gets re-enabled by resume.
1252                  */
1253                 stm32_port->cr3_irq =  USART_CR3_RXFTIE;
1254         }
1255
1256         cr1 |= stm32_port->cr1_irq;
1257         cr3 |= stm32_port->cr3_irq;
1258
1259         if (cflag & PARODD)
1260                 cr1 |= USART_CR1_PS;
1261
1262         port->status &= ~(UPSTAT_AUTOCTS | UPSTAT_AUTORTS);
1263         if (cflag & CRTSCTS) {
1264                 port->status |= UPSTAT_AUTOCTS | UPSTAT_AUTORTS;
1265                 cr3 |= USART_CR3_CTSE | USART_CR3_RTSE;
1266         }
1267
1268         usartdiv = DIV_ROUND_CLOSEST(port->uartclk, baud);
1269
1270         /*
1271          * The USART supports 16 or 8 times oversampling.
1272          * By default we prefer 16 times oversampling, so that the receiver
1273          * has a better tolerance to clock deviations.
1274          * 8 times oversampling is only used to achieve higher speeds.
1275          */
1276         if (usartdiv < 16) {
1277                 oversampling = 8;
1278                 cr1 |= USART_CR1_OVER8;
1279                 stm32_usart_set_bits(port, ofs->cr1, USART_CR1_OVER8);
1280         } else {
1281                 oversampling = 16;
1282                 cr1 &= ~USART_CR1_OVER8;
1283                 stm32_usart_clr_bits(port, ofs->cr1, USART_CR1_OVER8);
1284         }
1285
1286         mantissa = (usartdiv / oversampling) << USART_BRR_DIV_M_SHIFT;
1287         fraction = usartdiv % oversampling;
1288         writel_relaxed(mantissa | fraction, port->membase + ofs->brr);
1289
1290         uart_update_timeout(port, cflag, baud);
1291
1292         port->read_status_mask = USART_SR_ORE;
1293         if (termios->c_iflag & INPCK)
1294                 port->read_status_mask |= USART_SR_PE | USART_SR_FE;
1295         if (termios->c_iflag & (IGNBRK | BRKINT | PARMRK))
1296                 port->read_status_mask |= USART_SR_FE;
1297
1298         /* Characters to ignore */
1299         port->ignore_status_mask = 0;
1300         if (termios->c_iflag & IGNPAR)
1301                 port->ignore_status_mask = USART_SR_PE | USART_SR_FE;
1302         if (termios->c_iflag & IGNBRK) {
1303                 port->ignore_status_mask |= USART_SR_FE;
1304                 /*
1305                  * If we're ignoring parity and break indicators,
1306                  * ignore overruns too (for real raw support).
1307                  */
1308                 if (termios->c_iflag & IGNPAR)
1309                         port->ignore_status_mask |= USART_SR_ORE;
1310         }
1311
1312         /* Ignore all characters if CREAD is not set */
1313         if ((termios->c_cflag & CREAD) == 0)
1314                 port->ignore_status_mask |= USART_SR_DUMMY_RX;
1315
1316         if (stm32_port->rx_ch) {
1317                 /*
1318                  * Setup DMA to collect only valid data and enable error irqs.
1319                  * This also enables break reception when using DMA.
1320                  */
1321                 cr1 |= USART_CR1_PEIE;
1322                 cr3 |= USART_CR3_EIE;
1323                 cr3 |= USART_CR3_DMAR;
1324                 cr3 |= USART_CR3_DDRE;
1325         }
1326
1327         if (stm32_port->tx_ch)
1328                 cr3 |= USART_CR3_DMAT;
1329
1330         if (rs485conf->flags & SER_RS485_ENABLED) {
1331                 stm32_usart_config_reg_rs485(&cr1, &cr3,
1332                                              rs485conf->delay_rts_before_send,
1333                                              rs485conf->delay_rts_after_send,
1334                                              baud);
1335                 if (rs485conf->flags & SER_RS485_RTS_ON_SEND) {
1336                         cr3 &= ~USART_CR3_DEP;
1337                         rs485conf->flags &= ~SER_RS485_RTS_AFTER_SEND;
1338                 } else {
1339                         cr3 |= USART_CR3_DEP;
1340                         rs485conf->flags |= SER_RS485_RTS_AFTER_SEND;
1341                 }
1342
1343         } else {
1344                 cr3 &= ~(USART_CR3_DEM | USART_CR3_DEP);
1345                 cr1 &= ~(USART_CR1_DEDT_MASK | USART_CR1_DEAT_MASK);
1346         }
1347
1348         /* Configure wake up from low power on start bit detection */
1349         if (stm32_port->wakeup_src) {
1350                 cr3 &= ~USART_CR3_WUS_MASK;
1351                 cr3 |= USART_CR3_WUS_START_BIT;
1352         }
1353
1354         writel_relaxed(cr3, port->membase + ofs->cr3);
1355         writel_relaxed(cr2, port->membase + ofs->cr2);
1356         writel_relaxed(cr1, port->membase + ofs->cr1);
1357
1358         stm32_usart_set_bits(port, ofs->cr1, BIT(cfg->uart_enable_bit));
1359         uart_port_unlock_irqrestore(port, flags);
1360
1361         /* Handle modem control interrupts */
1362         if (UART_ENABLE_MS(port, termios->c_cflag))
1363                 stm32_usart_enable_ms(port);
1364         else
1365                 stm32_usart_disable_ms(port);
1366 }
1367
1368 static const char *stm32_usart_type(struct uart_port *port)
1369 {
1370         return (port->type == PORT_STM32) ? DRIVER_NAME : NULL;
1371 }
1372
1373 static void stm32_usart_release_port(struct uart_port *port)
1374 {
1375 }
1376
1377 static int stm32_usart_request_port(struct uart_port *port)
1378 {
1379         return 0;
1380 }
1381
1382 static void stm32_usart_config_port(struct uart_port *port, int flags)
1383 {
1384         if (flags & UART_CONFIG_TYPE)
1385                 port->type = PORT_STM32;
1386 }
1387
1388 static int
1389 stm32_usart_verify_port(struct uart_port *port, struct serial_struct *ser)
1390 {
1391         /* No user changeable parameters */
1392         return -EINVAL;
1393 }
1394
1395 static void stm32_usart_pm(struct uart_port *port, unsigned int state,
1396                            unsigned int oldstate)
1397 {
1398         struct stm32_port *stm32port = container_of(port,
1399                         struct stm32_port, port);
1400         const struct stm32_usart_offsets *ofs = &stm32port->info->ofs;
1401         const struct stm32_usart_config *cfg = &stm32port->info->cfg;
1402         unsigned long flags;
1403
1404         switch (state) {
1405         case UART_PM_STATE_ON:
1406                 pm_runtime_get_sync(port->dev);
1407                 break;
1408         case UART_PM_STATE_OFF:
1409                 uart_port_lock_irqsave(port, &flags);
1410                 stm32_usart_clr_bits(port, ofs->cr1, BIT(cfg->uart_enable_bit));
1411                 uart_port_unlock_irqrestore(port, flags);
1412                 pm_runtime_put_sync(port->dev);
1413                 break;
1414         }
1415 }
1416
1417 #if defined(CONFIG_CONSOLE_POLL)
1418
1419  /* Callbacks for characters polling in debug context (i.e. KGDB). */
1420 static int stm32_usart_poll_init(struct uart_port *port)
1421 {
1422         struct stm32_port *stm32_port = to_stm32_port(port);
1423
1424         return clk_prepare_enable(stm32_port->clk);
1425 }
1426
1427 static int stm32_usart_poll_get_char(struct uart_port *port)
1428 {
1429         struct stm32_port *stm32_port = to_stm32_port(port);
1430         const struct stm32_usart_offsets *ofs = &stm32_port->info->ofs;
1431
1432         if (!(readl_relaxed(port->membase + ofs->isr) & USART_SR_RXNE))
1433                 return NO_POLL_CHAR;
1434
1435         return readl_relaxed(port->membase + ofs->rdr) & stm32_port->rdr_mask;
1436 }
1437
1438 static void stm32_usart_poll_put_char(struct uart_port *port, unsigned char ch)
1439 {
1440         stm32_usart_console_putchar(port, ch);
1441 }
1442 #endif /* CONFIG_CONSOLE_POLL */
1443
1444 static const struct uart_ops stm32_uart_ops = {
1445         .tx_empty       = stm32_usart_tx_empty,
1446         .set_mctrl      = stm32_usart_set_mctrl,
1447         .get_mctrl      = stm32_usart_get_mctrl,
1448         .stop_tx        = stm32_usart_stop_tx,
1449         .start_tx       = stm32_usart_start_tx,
1450         .throttle       = stm32_usart_throttle,
1451         .unthrottle     = stm32_usart_unthrottle,
1452         .stop_rx        = stm32_usart_stop_rx,
1453         .enable_ms      = stm32_usart_enable_ms,
1454         .break_ctl      = stm32_usart_break_ctl,
1455         .startup        = stm32_usart_startup,
1456         .shutdown       = stm32_usart_shutdown,
1457         .flush_buffer   = stm32_usart_flush_buffer,
1458         .set_termios    = stm32_usart_set_termios,
1459         .pm             = stm32_usart_pm,
1460         .type           = stm32_usart_type,
1461         .release_port   = stm32_usart_release_port,
1462         .request_port   = stm32_usart_request_port,
1463         .config_port    = stm32_usart_config_port,
1464         .verify_port    = stm32_usart_verify_port,
1465 #if defined(CONFIG_CONSOLE_POLL)
1466         .poll_init      = stm32_usart_poll_init,
1467         .poll_get_char  = stm32_usart_poll_get_char,
1468         .poll_put_char  = stm32_usart_poll_put_char,
1469 #endif /* CONFIG_CONSOLE_POLL */
1470 };
1471
1472 /*
1473  * STM32H7 RX & TX FIFO threshold configuration (CR3 RXFTCFG / TXFTCFG)
1474  * Note: 1 isn't a valid value in RXFTCFG / TXFTCFG. In this case,
1475  * RXNEIE / TXEIE can be used instead of threshold irqs: RXFTIE / TXFTIE.
1476  * So, RXFTCFG / TXFTCFG bitfields values are encoded as array index + 1.
1477  */
1478 static const u32 stm32h7_usart_fifo_thresh_cfg[] = { 1, 2, 4, 8, 12, 14, 16 };
1479
1480 static void stm32_usart_get_ftcfg(struct platform_device *pdev, const char *p,
1481                                   int *ftcfg)
1482 {
1483         u32 bytes, i;
1484
1485         /* DT option to get RX & TX FIFO threshold (default to 8 bytes) */
1486         if (of_property_read_u32(pdev->dev.of_node, p, &bytes))
1487                 bytes = 8;
1488
1489         for (i = 0; i < ARRAY_SIZE(stm32h7_usart_fifo_thresh_cfg); i++)
1490                 if (stm32h7_usart_fifo_thresh_cfg[i] >= bytes)
1491                         break;
1492         if (i >= ARRAY_SIZE(stm32h7_usart_fifo_thresh_cfg))
1493                 i = ARRAY_SIZE(stm32h7_usart_fifo_thresh_cfg) - 1;
1494
1495         dev_dbg(&pdev->dev, "%s set to %d bytes\n", p,
1496                 stm32h7_usart_fifo_thresh_cfg[i]);
1497
1498         /* Provide FIFO threshold ftcfg (1 is invalid: threshold irq unused) */
1499         if (i)
1500                 *ftcfg = i - 1;
1501         else
1502                 *ftcfg = -EINVAL;
1503 }
1504
1505 static void stm32_usart_deinit_port(struct stm32_port *stm32port)
1506 {
1507         clk_disable_unprepare(stm32port->clk);
1508 }
1509
1510 static const struct serial_rs485 stm32_rs485_supported = {
1511         .flags = SER_RS485_ENABLED | SER_RS485_RTS_ON_SEND | SER_RS485_RTS_AFTER_SEND |
1512                  SER_RS485_RX_DURING_TX,
1513         .delay_rts_before_send = 1,
1514         .delay_rts_after_send = 1,
1515 };
1516
1517 static int stm32_usart_init_port(struct stm32_port *stm32port,
1518                                  struct platform_device *pdev)
1519 {
1520         struct uart_port *port = &stm32port->port;
1521         struct resource *res;
1522         int ret, irq;
1523
1524         irq = platform_get_irq(pdev, 0);
1525         if (irq < 0)
1526                 return irq;
1527
1528         port->iotype    = UPIO_MEM;
1529         port->flags     = UPF_BOOT_AUTOCONF;
1530         port->ops       = &stm32_uart_ops;
1531         port->dev       = &pdev->dev;
1532         port->fifosize  = stm32port->info->cfg.fifosize;
1533         port->has_sysrq = IS_ENABLED(CONFIG_SERIAL_STM32_CONSOLE);
1534         port->irq = irq;
1535         port->rs485_config = stm32_usart_config_rs485;
1536         port->rs485_supported = stm32_rs485_supported;
1537
1538         ret = stm32_usart_init_rs485(port, pdev);
1539         if (ret)
1540                 return ret;
1541
1542         stm32port->wakeup_src = stm32port->info->cfg.has_wakeup &&
1543                 of_property_read_bool(pdev->dev.of_node, "wakeup-source");
1544
1545         stm32port->swap = stm32port->info->cfg.has_swap &&
1546                 of_property_read_bool(pdev->dev.of_node, "rx-tx-swap");
1547
1548         stm32port->fifoen = stm32port->info->cfg.has_fifo;
1549         if (stm32port->fifoen) {
1550                 stm32_usart_get_ftcfg(pdev, "rx-threshold",
1551                                       &stm32port->rxftcfg);
1552                 stm32_usart_get_ftcfg(pdev, "tx-threshold",
1553                                       &stm32port->txftcfg);
1554         }
1555
1556         port->membase = devm_platform_get_and_ioremap_resource(pdev, 0, &res);
1557         if (IS_ERR(port->membase))
1558                 return PTR_ERR(port->membase);
1559         port->mapbase = res->start;
1560
1561         spin_lock_init(&port->lock);
1562
1563         stm32port->clk = devm_clk_get(&pdev->dev, NULL);
1564         if (IS_ERR(stm32port->clk))
1565                 return PTR_ERR(stm32port->clk);
1566
1567         /* Ensure that clk rate is correct by enabling the clk */
1568         ret = clk_prepare_enable(stm32port->clk);
1569         if (ret)
1570                 return ret;
1571
1572         stm32port->port.uartclk = clk_get_rate(stm32port->clk);
1573         if (!stm32port->port.uartclk) {
1574                 ret = -EINVAL;
1575                 goto err_clk;
1576         }
1577
1578         stm32port->gpios = mctrl_gpio_init(&stm32port->port, 0);
1579         if (IS_ERR(stm32port->gpios)) {
1580                 ret = PTR_ERR(stm32port->gpios);
1581                 goto err_clk;
1582         }
1583
1584         /*
1585          * Both CTS/RTS gpios and "st,hw-flow-ctrl" (deprecated) or "uart-has-rtscts"
1586          * properties should not be specified.
1587          */
1588         if (stm32port->hw_flow_control) {
1589                 if (mctrl_gpio_to_gpiod(stm32port->gpios, UART_GPIO_CTS) ||
1590                     mctrl_gpio_to_gpiod(stm32port->gpios, UART_GPIO_RTS)) {
1591                         dev_err(&pdev->dev, "Conflicting RTS/CTS config\n");
1592                         ret = -EINVAL;
1593                         goto err_clk;
1594                 }
1595         }
1596
1597         return ret;
1598
1599 err_clk:
1600         clk_disable_unprepare(stm32port->clk);
1601
1602         return ret;
1603 }
1604
1605 static struct stm32_port *stm32_usart_of_get_port(struct platform_device *pdev)
1606 {
1607         struct device_node *np = pdev->dev.of_node;
1608         int id;
1609
1610         if (!np)
1611                 return NULL;
1612
1613         id = of_alias_get_id(np, "serial");
1614         if (id < 0) {
1615                 dev_err(&pdev->dev, "failed to get alias id, errno %d\n", id);
1616                 return NULL;
1617         }
1618
1619         if (WARN_ON(id >= STM32_MAX_PORTS))
1620                 return NULL;
1621
1622         stm32_ports[id].hw_flow_control =
1623                 of_property_read_bool (np, "st,hw-flow-ctrl") /*deprecated*/ ||
1624                 of_property_read_bool (np, "uart-has-rtscts");
1625         stm32_ports[id].port.line = id;
1626         stm32_ports[id].cr1_irq = USART_CR1_RXNEIE;
1627         stm32_ports[id].cr3_irq = 0;
1628         stm32_ports[id].last_res = RX_BUF_L;
1629         return &stm32_ports[id];
1630 }
1631
1632 #ifdef CONFIG_OF
1633 static const struct of_device_id stm32_match[] = {
1634         { .compatible = "st,stm32-uart", .data = &stm32f4_info},
1635         { .compatible = "st,stm32f7-uart", .data = &stm32f7_info},
1636         { .compatible = "st,stm32h7-uart", .data = &stm32h7_info},
1637         {},
1638 };
1639
1640 MODULE_DEVICE_TABLE(of, stm32_match);
1641 #endif
1642
1643 static void stm32_usart_of_dma_rx_remove(struct stm32_port *stm32port,
1644                                          struct platform_device *pdev)
1645 {
1646         if (stm32port->rx_buf)
1647                 dma_free_coherent(&pdev->dev, RX_BUF_L, stm32port->rx_buf,
1648                                   stm32port->rx_dma_buf);
1649 }
1650
1651 static int stm32_usart_of_dma_rx_probe(struct stm32_port *stm32port,
1652                                        struct platform_device *pdev)
1653 {
1654         const struct stm32_usart_offsets *ofs = &stm32port->info->ofs;
1655         struct uart_port *port = &stm32port->port;
1656         struct device *dev = &pdev->dev;
1657         struct dma_slave_config config;
1658         int ret;
1659
1660         stm32port->rx_buf = dma_alloc_coherent(dev, RX_BUF_L,
1661                                                &stm32port->rx_dma_buf,
1662                                                GFP_KERNEL);
1663         if (!stm32port->rx_buf)
1664                 return -ENOMEM;
1665
1666         /* Configure DMA channel */
1667         memset(&config, 0, sizeof(config));
1668         config.src_addr = port->mapbase + ofs->rdr;
1669         config.src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
1670
1671         ret = dmaengine_slave_config(stm32port->rx_ch, &config);
1672         if (ret < 0) {
1673                 dev_err(dev, "rx dma channel config failed\n");
1674                 stm32_usart_of_dma_rx_remove(stm32port, pdev);
1675                 return ret;
1676         }
1677
1678         return 0;
1679 }
1680
1681 static void stm32_usart_of_dma_tx_remove(struct stm32_port *stm32port,
1682                                          struct platform_device *pdev)
1683 {
1684         if (stm32port->tx_buf)
1685                 dma_free_coherent(&pdev->dev, TX_BUF_L, stm32port->tx_buf,
1686                                   stm32port->tx_dma_buf);
1687 }
1688
1689 static int stm32_usart_of_dma_tx_probe(struct stm32_port *stm32port,
1690                                        struct platform_device *pdev)
1691 {
1692         const struct stm32_usart_offsets *ofs = &stm32port->info->ofs;
1693         struct uart_port *port = &stm32port->port;
1694         struct device *dev = &pdev->dev;
1695         struct dma_slave_config config;
1696         int ret;
1697
1698         stm32port->tx_buf = dma_alloc_coherent(dev, TX_BUF_L,
1699                                                &stm32port->tx_dma_buf,
1700                                                GFP_KERNEL);
1701         if (!stm32port->tx_buf)
1702                 return -ENOMEM;
1703
1704         /* Configure DMA channel */
1705         memset(&config, 0, sizeof(config));
1706         config.dst_addr = port->mapbase + ofs->tdr;
1707         config.dst_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
1708
1709         ret = dmaengine_slave_config(stm32port->tx_ch, &config);
1710         if (ret < 0) {
1711                 dev_err(dev, "tx dma channel config failed\n");
1712                 stm32_usart_of_dma_tx_remove(stm32port, pdev);
1713                 return ret;
1714         }
1715
1716         return 0;
1717 }
1718
1719 static int stm32_usart_serial_probe(struct platform_device *pdev)
1720 {
1721         struct stm32_port *stm32port;
1722         int ret;
1723
1724         stm32port = stm32_usart_of_get_port(pdev);
1725         if (!stm32port)
1726                 return -ENODEV;
1727
1728         stm32port->info = of_device_get_match_data(&pdev->dev);
1729         if (!stm32port->info)
1730                 return -EINVAL;
1731
1732         stm32port->rx_ch = dma_request_chan(&pdev->dev, "rx");
1733         if (PTR_ERR(stm32port->rx_ch) == -EPROBE_DEFER)
1734                 return -EPROBE_DEFER;
1735
1736         /* Fall back in interrupt mode for any non-deferral error */
1737         if (IS_ERR(stm32port->rx_ch))
1738                 stm32port->rx_ch = NULL;
1739
1740         stm32port->tx_ch = dma_request_chan(&pdev->dev, "tx");
1741         if (PTR_ERR(stm32port->tx_ch) == -EPROBE_DEFER) {
1742                 ret = -EPROBE_DEFER;
1743                 goto err_dma_rx;
1744         }
1745         /* Fall back in interrupt mode for any non-deferral error */
1746         if (IS_ERR(stm32port->tx_ch))
1747                 stm32port->tx_ch = NULL;
1748
1749         ret = stm32_usart_init_port(stm32port, pdev);
1750         if (ret)
1751                 goto err_dma_tx;
1752
1753         if (stm32port->wakeup_src) {
1754                 device_set_wakeup_capable(&pdev->dev, true);
1755                 ret = dev_pm_set_wake_irq(&pdev->dev, stm32port->port.irq);
1756                 if (ret)
1757                         goto err_deinit_port;
1758         }
1759
1760         if (stm32port->rx_ch && stm32_usart_of_dma_rx_probe(stm32port, pdev)) {
1761                 /* Fall back in interrupt mode */
1762                 dma_release_channel(stm32port->rx_ch);
1763                 stm32port->rx_ch = NULL;
1764         }
1765
1766         if (stm32port->tx_ch && stm32_usart_of_dma_tx_probe(stm32port, pdev)) {
1767                 /* Fall back in interrupt mode */
1768                 dma_release_channel(stm32port->tx_ch);
1769                 stm32port->tx_ch = NULL;
1770         }
1771
1772         if (!stm32port->rx_ch)
1773                 dev_info(&pdev->dev, "interrupt mode for rx (no dma)\n");
1774         if (!stm32port->tx_ch)
1775                 dev_info(&pdev->dev, "interrupt mode for tx (no dma)\n");
1776
1777         platform_set_drvdata(pdev, &stm32port->port);
1778
1779         pm_runtime_get_noresume(&pdev->dev);
1780         pm_runtime_set_active(&pdev->dev);
1781         pm_runtime_enable(&pdev->dev);
1782
1783         ret = uart_add_one_port(&stm32_usart_driver, &stm32port->port);
1784         if (ret)
1785                 goto err_port;
1786
1787         pm_runtime_put_sync(&pdev->dev);
1788
1789         return 0;
1790
1791 err_port:
1792         pm_runtime_disable(&pdev->dev);
1793         pm_runtime_set_suspended(&pdev->dev);
1794         pm_runtime_put_noidle(&pdev->dev);
1795
1796         if (stm32port->tx_ch)
1797                 stm32_usart_of_dma_tx_remove(stm32port, pdev);
1798         if (stm32port->rx_ch)
1799                 stm32_usart_of_dma_rx_remove(stm32port, pdev);
1800
1801         if (stm32port->wakeup_src)
1802                 dev_pm_clear_wake_irq(&pdev->dev);
1803
1804 err_deinit_port:
1805         if (stm32port->wakeup_src)
1806                 device_set_wakeup_capable(&pdev->dev, false);
1807
1808         stm32_usart_deinit_port(stm32port);
1809
1810 err_dma_tx:
1811         if (stm32port->tx_ch)
1812                 dma_release_channel(stm32port->tx_ch);
1813
1814 err_dma_rx:
1815         if (stm32port->rx_ch)
1816                 dma_release_channel(stm32port->rx_ch);
1817
1818         return ret;
1819 }
1820
1821 static void stm32_usart_serial_remove(struct platform_device *pdev)
1822 {
1823         struct uart_port *port = platform_get_drvdata(pdev);
1824         struct stm32_port *stm32_port = to_stm32_port(port);
1825         const struct stm32_usart_offsets *ofs = &stm32_port->info->ofs;
1826         u32 cr3;
1827
1828         pm_runtime_get_sync(&pdev->dev);
1829         uart_remove_one_port(&stm32_usart_driver, port);
1830
1831         pm_runtime_disable(&pdev->dev);
1832         pm_runtime_set_suspended(&pdev->dev);
1833         pm_runtime_put_noidle(&pdev->dev);
1834
1835         stm32_usart_clr_bits(port, ofs->cr1, USART_CR1_PEIE);
1836
1837         if (stm32_port->tx_ch) {
1838                 stm32_usart_of_dma_tx_remove(stm32_port, pdev);
1839                 dma_release_channel(stm32_port->tx_ch);
1840         }
1841
1842         if (stm32_port->rx_ch) {
1843                 stm32_usart_of_dma_rx_remove(stm32_port, pdev);
1844                 dma_release_channel(stm32_port->rx_ch);
1845         }
1846
1847         cr3 = readl_relaxed(port->membase + ofs->cr3);
1848         cr3 &= ~USART_CR3_EIE;
1849         cr3 &= ~USART_CR3_DMAR;
1850         cr3 &= ~USART_CR3_DMAT;
1851         cr3 &= ~USART_CR3_DDRE;
1852         writel_relaxed(cr3, port->membase + ofs->cr3);
1853
1854         if (stm32_port->wakeup_src) {
1855                 dev_pm_clear_wake_irq(&pdev->dev);
1856                 device_init_wakeup(&pdev->dev, false);
1857         }
1858
1859         stm32_usart_deinit_port(stm32_port);
1860 }
1861
1862 static void __maybe_unused stm32_usart_console_putchar(struct uart_port *port, unsigned char ch)
1863 {
1864         struct stm32_port *stm32_port = to_stm32_port(port);
1865         const struct stm32_usart_offsets *ofs = &stm32_port->info->ofs;
1866         u32 isr;
1867         int ret;
1868
1869         ret = readl_relaxed_poll_timeout_atomic(port->membase + ofs->isr, isr,
1870                                                 (isr & USART_SR_TXE), 100,
1871                                                 STM32_USART_TIMEOUT_USEC);
1872         if (ret != 0) {
1873                 dev_err(port->dev, "Error while sending data in UART TX : %d\n", ret);
1874                 return;
1875         }
1876         writel_relaxed(ch, port->membase + ofs->tdr);
1877 }
1878
1879 #ifdef CONFIG_SERIAL_STM32_CONSOLE
1880 static void stm32_usart_console_write(struct console *co, const char *s,
1881                                       unsigned int cnt)
1882 {
1883         struct uart_port *port = &stm32_ports[co->index].port;
1884         struct stm32_port *stm32_port = to_stm32_port(port);
1885         const struct stm32_usart_offsets *ofs = &stm32_port->info->ofs;
1886         const struct stm32_usart_config *cfg = &stm32_port->info->cfg;
1887         unsigned long flags;
1888         u32 old_cr1, new_cr1;
1889         int locked = 1;
1890
1891         if (oops_in_progress)
1892                 locked = uart_port_trylock_irqsave(port, &flags);
1893         else
1894                 uart_port_lock_irqsave(port, &flags);
1895
1896         /* Save and disable interrupts, enable the transmitter */
1897         old_cr1 = readl_relaxed(port->membase + ofs->cr1);
1898         new_cr1 = old_cr1 & ~USART_CR1_IE_MASK;
1899         new_cr1 |=  USART_CR1_TE | BIT(cfg->uart_enable_bit);
1900         writel_relaxed(new_cr1, port->membase + ofs->cr1);
1901
1902         uart_console_write(port, s, cnt, stm32_usart_console_putchar);
1903
1904         /* Restore interrupt state */
1905         writel_relaxed(old_cr1, port->membase + ofs->cr1);
1906
1907         if (locked)
1908                 uart_port_unlock_irqrestore(port, flags);
1909 }
1910
1911 static int stm32_usart_console_setup(struct console *co, char *options)
1912 {
1913         struct stm32_port *stm32port;
1914         int baud = 9600;
1915         int bits = 8;
1916         int parity = 'n';
1917         int flow = 'n';
1918
1919         if (co->index >= STM32_MAX_PORTS)
1920                 return -ENODEV;
1921
1922         stm32port = &stm32_ports[co->index];
1923
1924         /*
1925          * This driver does not support early console initialization
1926          * (use ARM early printk support instead), so we only expect
1927          * this to be called during the uart port registration when the
1928          * driver gets probed and the port should be mapped at that point.
1929          */
1930         if (stm32port->port.mapbase == 0 || !stm32port->port.membase)
1931                 return -ENXIO;
1932
1933         if (options)
1934                 uart_parse_options(options, &baud, &parity, &bits, &flow);
1935
1936         return uart_set_options(&stm32port->port, co, baud, parity, bits, flow);
1937 }
1938
1939 static struct console stm32_console = {
1940         .name           = STM32_SERIAL_NAME,
1941         .device         = uart_console_device,
1942         .write          = stm32_usart_console_write,
1943         .setup          = stm32_usart_console_setup,
1944         .flags          = CON_PRINTBUFFER,
1945         .index          = -1,
1946         .data           = &stm32_usart_driver,
1947 };
1948
1949 #define STM32_SERIAL_CONSOLE (&stm32_console)
1950
1951 #else
1952 #define STM32_SERIAL_CONSOLE NULL
1953 #endif /* CONFIG_SERIAL_STM32_CONSOLE */
1954
1955 #ifdef CONFIG_SERIAL_EARLYCON
1956 static void early_stm32_usart_console_putchar(struct uart_port *port, unsigned char ch)
1957 {
1958         struct stm32_usart_info *info = port->private_data;
1959
1960         while (!(readl_relaxed(port->membase + info->ofs.isr) & USART_SR_TXE))
1961                 cpu_relax();
1962
1963         writel_relaxed(ch, port->membase + info->ofs.tdr);
1964 }
1965
1966 static void early_stm32_serial_write(struct console *console, const char *s, unsigned int count)
1967 {
1968         struct earlycon_device *device = console->data;
1969         struct uart_port *port = &device->port;
1970
1971         uart_console_write(port, s, count, early_stm32_usart_console_putchar);
1972 }
1973
1974 static int __init early_stm32_h7_serial_setup(struct earlycon_device *device, const char *options)
1975 {
1976         if (!(device->port.membase || device->port.iobase))
1977                 return -ENODEV;
1978         device->port.private_data = &stm32h7_info;
1979         device->con->write = early_stm32_serial_write;
1980         return 0;
1981 }
1982
1983 static int __init early_stm32_f7_serial_setup(struct earlycon_device *device, const char *options)
1984 {
1985         if (!(device->port.membase || device->port.iobase))
1986                 return -ENODEV;
1987         device->port.private_data = &stm32f7_info;
1988         device->con->write = early_stm32_serial_write;
1989         return 0;
1990 }
1991
1992 static int __init early_stm32_f4_serial_setup(struct earlycon_device *device, const char *options)
1993 {
1994         if (!(device->port.membase || device->port.iobase))
1995                 return -ENODEV;
1996         device->port.private_data = &stm32f4_info;
1997         device->con->write = early_stm32_serial_write;
1998         return 0;
1999 }
2000
2001 OF_EARLYCON_DECLARE(stm32, "st,stm32h7-uart", early_stm32_h7_serial_setup);
2002 OF_EARLYCON_DECLARE(stm32, "st,stm32f7-uart", early_stm32_f7_serial_setup);
2003 OF_EARLYCON_DECLARE(stm32, "st,stm32-uart", early_stm32_f4_serial_setup);
2004 #endif /* CONFIG_SERIAL_EARLYCON */
2005
2006 static struct uart_driver stm32_usart_driver = {
2007         .driver_name    = DRIVER_NAME,
2008         .dev_name       = STM32_SERIAL_NAME,
2009         .major          = 0,
2010         .minor          = 0,
2011         .nr             = STM32_MAX_PORTS,
2012         .cons           = STM32_SERIAL_CONSOLE,
2013 };
2014
2015 static int __maybe_unused stm32_usart_serial_en_wakeup(struct uart_port *port,
2016                                                        bool enable)
2017 {
2018         struct stm32_port *stm32_port = to_stm32_port(port);
2019         const struct stm32_usart_offsets *ofs = &stm32_port->info->ofs;
2020         struct tty_port *tport = &port->state->port;
2021         int ret;
2022         unsigned int size = 0;
2023         unsigned long flags;
2024
2025         if (!stm32_port->wakeup_src || !tty_port_initialized(tport))
2026                 return 0;
2027
2028         /*
2029          * Enable low-power wake-up and wake-up irq if argument is set to
2030          * "enable", disable low-power wake-up and wake-up irq otherwise
2031          */
2032         if (enable) {
2033                 stm32_usart_set_bits(port, ofs->cr1, USART_CR1_UESM);
2034                 stm32_usart_set_bits(port, ofs->cr3, USART_CR3_WUFIE);
2035                 mctrl_gpio_enable_irq_wake(stm32_port->gpios);
2036
2037                 /*
2038                  * When DMA is used for reception, it must be disabled before
2039                  * entering low-power mode and re-enabled when exiting from
2040                  * low-power mode.
2041                  */
2042                 if (stm32_port->rx_ch) {
2043                         uart_port_lock_irqsave(port, &flags);
2044                         /* Poll data from DMA RX buffer if any */
2045                         if (!stm32_usart_rx_dma_pause(stm32_port))
2046                                 size += stm32_usart_receive_chars(port, true);
2047                         stm32_usart_rx_dma_terminate(stm32_port);
2048                         uart_unlock_and_check_sysrq_irqrestore(port, flags);
2049                         if (size)
2050                                 tty_flip_buffer_push(tport);
2051                 }
2052
2053                 /* Poll data from RX FIFO if any */
2054                 stm32_usart_receive_chars(port, false);
2055         } else {
2056                 if (stm32_port->rx_ch) {
2057                         ret = stm32_usart_rx_dma_start_or_resume(port);
2058                         if (ret)
2059                                 return ret;
2060                 }
2061                 mctrl_gpio_disable_irq_wake(stm32_port->gpios);
2062                 stm32_usart_clr_bits(port, ofs->cr1, USART_CR1_UESM);
2063                 stm32_usart_clr_bits(port, ofs->cr3, USART_CR3_WUFIE);
2064         }
2065
2066         return 0;
2067 }
2068
2069 static int __maybe_unused stm32_usart_serial_suspend(struct device *dev)
2070 {
2071         struct uart_port *port = dev_get_drvdata(dev);
2072         int ret;
2073
2074         uart_suspend_port(&stm32_usart_driver, port);
2075
2076         if (device_may_wakeup(dev) || device_wakeup_path(dev)) {
2077                 ret = stm32_usart_serial_en_wakeup(port, true);
2078                 if (ret)
2079                         return ret;
2080         }
2081
2082         /*
2083          * When "no_console_suspend" is enabled, keep the pinctrl default state
2084          * and rely on bootloader stage to restore this state upon resume.
2085          * Otherwise, apply the idle or sleep states depending on wakeup
2086          * capabilities.
2087          */
2088         if (console_suspend_enabled || !uart_console(port)) {
2089                 if (device_may_wakeup(dev) || device_wakeup_path(dev))
2090                         pinctrl_pm_select_idle_state(dev);
2091                 else
2092                         pinctrl_pm_select_sleep_state(dev);
2093         }
2094
2095         return 0;
2096 }
2097
2098 static int __maybe_unused stm32_usart_serial_resume(struct device *dev)
2099 {
2100         struct uart_port *port = dev_get_drvdata(dev);
2101         int ret;
2102
2103         pinctrl_pm_select_default_state(dev);
2104
2105         if (device_may_wakeup(dev) || device_wakeup_path(dev)) {
2106                 ret = stm32_usart_serial_en_wakeup(port, false);
2107                 if (ret)
2108                         return ret;
2109         }
2110
2111         return uart_resume_port(&stm32_usart_driver, port);
2112 }
2113
2114 static int __maybe_unused stm32_usart_runtime_suspend(struct device *dev)
2115 {
2116         struct uart_port *port = dev_get_drvdata(dev);
2117         struct stm32_port *stm32port = container_of(port,
2118                         struct stm32_port, port);
2119
2120         clk_disable_unprepare(stm32port->clk);
2121
2122         return 0;
2123 }
2124
2125 static int __maybe_unused stm32_usart_runtime_resume(struct device *dev)
2126 {
2127         struct uart_port *port = dev_get_drvdata(dev);
2128         struct stm32_port *stm32port = container_of(port,
2129                         struct stm32_port, port);
2130
2131         return clk_prepare_enable(stm32port->clk);
2132 }
2133
2134 static const struct dev_pm_ops stm32_serial_pm_ops = {
2135         SET_RUNTIME_PM_OPS(stm32_usart_runtime_suspend,
2136                            stm32_usart_runtime_resume, NULL)
2137         SET_SYSTEM_SLEEP_PM_OPS(stm32_usart_serial_suspend,
2138                                 stm32_usart_serial_resume)
2139 };
2140
2141 static struct platform_driver stm32_serial_driver = {
2142         .probe          = stm32_usart_serial_probe,
2143         .remove_new     = stm32_usart_serial_remove,
2144         .driver = {
2145                 .name   = DRIVER_NAME,
2146                 .pm     = &stm32_serial_pm_ops,
2147                 .of_match_table = of_match_ptr(stm32_match),
2148         },
2149 };
2150
2151 static int __init stm32_usart_init(void)
2152 {
2153         static char banner[] __initdata = "STM32 USART driver initialized";
2154         int ret;
2155
2156         pr_info("%s\n", banner);
2157
2158         ret = uart_register_driver(&stm32_usart_driver);
2159         if (ret)
2160                 return ret;
2161
2162         ret = platform_driver_register(&stm32_serial_driver);
2163         if (ret)
2164                 uart_unregister_driver(&stm32_usart_driver);
2165
2166         return ret;
2167 }
2168
2169 static void __exit stm32_usart_exit(void)
2170 {
2171         platform_driver_unregister(&stm32_serial_driver);
2172         uart_unregister_driver(&stm32_usart_driver);
2173 }
2174
2175 module_init(stm32_usart_init);
2176 module_exit(stm32_usart_exit);
2177
2178 MODULE_ALIAS("platform:" DRIVER_NAME);
2179 MODULE_DESCRIPTION("STMicroelectronics STM32 serial port driver");
2180 MODULE_LICENSE("GPL v2");