1 // SPDX-License-Identifier: GPL-2.0+
3 * Driver for SA11x0 serial ports
5 * Based on drivers/char/serial.c, by Linus Torvalds, Theodore Ts'o.
7 * Copyright (C) 2000 Deep Blue Solutions Ltd.
10 #include <linux/module.h>
11 #include <linux/ioport.h>
12 #include <linux/init.h>
13 #include <linux/console.h>
14 #include <linux/sysrq.h>
15 #include <linux/platform_data/sa11x0-serial.h>
16 #include <linux/platform_device.h>
17 #include <linux/tty.h>
18 #include <linux/tty_flip.h>
19 #include <linux/serial_core.h>
20 #include <linux/serial.h>
24 #include <mach/hardware.h>
25 #include <mach/irqs.h>
27 #include "serial_mctrl_gpio.h"
29 /* We've been assigned a range on the "Low-density serial ports" major */
30 #define SERIAL_SA1100_MAJOR 204
35 #define SA1100_ISR_PASS_LIMIT 256
38 * Convert from ignore_status_mask or read_status_mask to UTSR[01]
40 #define SM_TO_UTSR0(x) ((x) & 0xff)
41 #define SM_TO_UTSR1(x) ((x) >> 8)
42 #define UTSR0_TO_SM(x) ((x))
43 #define UTSR1_TO_SM(x) ((x) << 8)
45 #define UART_GET_UTCR0(sport) __raw_readl((sport)->port.membase + UTCR0)
46 #define UART_GET_UTCR1(sport) __raw_readl((sport)->port.membase + UTCR1)
47 #define UART_GET_UTCR2(sport) __raw_readl((sport)->port.membase + UTCR2)
48 #define UART_GET_UTCR3(sport) __raw_readl((sport)->port.membase + UTCR3)
49 #define UART_GET_UTSR0(sport) __raw_readl((sport)->port.membase + UTSR0)
50 #define UART_GET_UTSR1(sport) __raw_readl((sport)->port.membase + UTSR1)
51 #define UART_GET_CHAR(sport) __raw_readl((sport)->port.membase + UTDR)
53 #define UART_PUT_UTCR0(sport,v) __raw_writel((v),(sport)->port.membase + UTCR0)
54 #define UART_PUT_UTCR1(sport,v) __raw_writel((v),(sport)->port.membase + UTCR1)
55 #define UART_PUT_UTCR2(sport,v) __raw_writel((v),(sport)->port.membase + UTCR2)
56 #define UART_PUT_UTCR3(sport,v) __raw_writel((v),(sport)->port.membase + UTCR3)
57 #define UART_PUT_UTSR0(sport,v) __raw_writel((v),(sport)->port.membase + UTSR0)
58 #define UART_PUT_UTSR1(sport,v) __raw_writel((v),(sport)->port.membase + UTSR1)
59 #define UART_PUT_CHAR(sport,v) __raw_writel((v),(sport)->port.membase + UTDR)
62 * This is the size of our serial port register set.
64 #define UART_PORT_SIZE 0x24
67 * This determines how often we check the modem status signals
68 * for any change. They generally aren't connected to an IRQ
69 * so we have to poll them. We also check immediately before
70 * filling the TX fifo incase CTS has been dropped.
72 #define MCTRL_TIMEOUT (250*HZ/1000)
75 struct uart_port port;
76 struct timer_list timer;
77 unsigned int old_status;
78 struct mctrl_gpios *gpios;
82 * Handle any change of modem status signal since we were last called.
84 static void sa1100_mctrl_check(struct sa1100_port *sport)
86 unsigned int status, changed;
88 status = sport->port.ops->get_mctrl(&sport->port);
89 changed = status ^ sport->old_status;
94 sport->old_status = status;
96 if (changed & TIOCM_RI)
97 sport->port.icount.rng++;
98 if (changed & TIOCM_DSR)
99 sport->port.icount.dsr++;
100 if (changed & TIOCM_CAR)
101 uart_handle_dcd_change(&sport->port, status & TIOCM_CAR);
102 if (changed & TIOCM_CTS)
103 uart_handle_cts_change(&sport->port, status & TIOCM_CTS);
105 wake_up_interruptible(&sport->port.state->port.delta_msr_wait);
109 * This is our per-port timeout handler, for checking the
110 * modem status signals.
112 static void sa1100_timeout(struct timer_list *t)
114 struct sa1100_port *sport = from_timer(sport, t, timer);
117 if (sport->port.state) {
118 spin_lock_irqsave(&sport->port.lock, flags);
119 sa1100_mctrl_check(sport);
120 spin_unlock_irqrestore(&sport->port.lock, flags);
122 mod_timer(&sport->timer, jiffies + MCTRL_TIMEOUT);
127 * interrupts disabled on entry
129 static void sa1100_stop_tx(struct uart_port *port)
131 struct sa1100_port *sport =
132 container_of(port, struct sa1100_port, port);
135 utcr3 = UART_GET_UTCR3(sport);
136 UART_PUT_UTCR3(sport, utcr3 & ~UTCR3_TIE);
137 sport->port.read_status_mask &= ~UTSR0_TO_SM(UTSR0_TFS);
141 * port locked and interrupts disabled
143 static void sa1100_start_tx(struct uart_port *port)
145 struct sa1100_port *sport =
146 container_of(port, struct sa1100_port, port);
149 utcr3 = UART_GET_UTCR3(sport);
150 sport->port.read_status_mask |= UTSR0_TO_SM(UTSR0_TFS);
151 UART_PUT_UTCR3(sport, utcr3 | UTCR3_TIE);
157 static void sa1100_stop_rx(struct uart_port *port)
159 struct sa1100_port *sport =
160 container_of(port, struct sa1100_port, port);
163 utcr3 = UART_GET_UTCR3(sport);
164 UART_PUT_UTCR3(sport, utcr3 & ~UTCR3_RIE);
168 * Set the modem control timer to fire immediately.
170 static void sa1100_enable_ms(struct uart_port *port)
172 struct sa1100_port *sport =
173 container_of(port, struct sa1100_port, port);
175 mod_timer(&sport->timer, jiffies);
177 mctrl_gpio_enable_ms(sport->gpios);
181 sa1100_rx_chars(struct sa1100_port *sport)
183 unsigned int status, ch, flg;
185 status = UTSR1_TO_SM(UART_GET_UTSR1(sport)) |
186 UTSR0_TO_SM(UART_GET_UTSR0(sport));
187 while (status & UTSR1_TO_SM(UTSR1_RNE)) {
188 ch = UART_GET_CHAR(sport);
190 sport->port.icount.rx++;
195 * note that the error handling code is
196 * out of the main execution path
198 if (status & UTSR1_TO_SM(UTSR1_PRE | UTSR1_FRE | UTSR1_ROR)) {
199 if (status & UTSR1_TO_SM(UTSR1_PRE))
200 sport->port.icount.parity++;
201 else if (status & UTSR1_TO_SM(UTSR1_FRE))
202 sport->port.icount.frame++;
203 if (status & UTSR1_TO_SM(UTSR1_ROR))
204 sport->port.icount.overrun++;
206 status &= sport->port.read_status_mask;
208 if (status & UTSR1_TO_SM(UTSR1_PRE))
210 else if (status & UTSR1_TO_SM(UTSR1_FRE))
213 sport->port.sysrq = 0;
216 if (uart_handle_sysrq_char(&sport->port, ch))
219 uart_insert_char(&sport->port, status, UTSR1_TO_SM(UTSR1_ROR), ch, flg);
222 status = UTSR1_TO_SM(UART_GET_UTSR1(sport)) |
223 UTSR0_TO_SM(UART_GET_UTSR0(sport));
226 tty_flip_buffer_push(&sport->port.state->port);
229 static void sa1100_tx_chars(struct sa1100_port *sport)
234 * Check the modem control lines before
235 * transmitting anything.
237 sa1100_mctrl_check(sport);
239 uart_port_tx(&sport->port, ch,
240 UART_GET_UTSR1(sport) & UTSR1_TNF,
241 UART_PUT_CHAR(sport, ch));
244 static irqreturn_t sa1100_int(int irq, void *dev_id)
246 struct sa1100_port *sport = dev_id;
247 unsigned int status, pass_counter = 0;
249 spin_lock(&sport->port.lock);
250 status = UART_GET_UTSR0(sport);
251 status &= SM_TO_UTSR0(sport->port.read_status_mask) | ~UTSR0_TFS;
253 if (status & (UTSR0_RFS | UTSR0_RID)) {
254 /* Clear the receiver idle bit, if set */
255 if (status & UTSR0_RID)
256 UART_PUT_UTSR0(sport, UTSR0_RID);
257 sa1100_rx_chars(sport);
260 /* Clear the relevant break bits */
261 if (status & (UTSR0_RBB | UTSR0_REB))
262 UART_PUT_UTSR0(sport, status & (UTSR0_RBB | UTSR0_REB));
264 if (status & UTSR0_RBB)
265 sport->port.icount.brk++;
267 if (status & UTSR0_REB)
268 uart_handle_break(&sport->port);
270 if (status & UTSR0_TFS)
271 sa1100_tx_chars(sport);
272 if (pass_counter++ > SA1100_ISR_PASS_LIMIT)
274 status = UART_GET_UTSR0(sport);
275 status &= SM_TO_UTSR0(sport->port.read_status_mask) |
277 } while (status & (UTSR0_TFS | UTSR0_RFS | UTSR0_RID));
278 spin_unlock(&sport->port.lock);
284 * Return TIOCSER_TEMT when transmitter is not busy.
286 static unsigned int sa1100_tx_empty(struct uart_port *port)
288 struct sa1100_port *sport =
289 container_of(port, struct sa1100_port, port);
291 return UART_GET_UTSR1(sport) & UTSR1_TBY ? 0 : TIOCSER_TEMT;
294 static unsigned int sa1100_get_mctrl(struct uart_port *port)
296 struct sa1100_port *sport =
297 container_of(port, struct sa1100_port, port);
298 int ret = TIOCM_CTS | TIOCM_DSR | TIOCM_CAR;
300 mctrl_gpio_get(sport->gpios, &ret);
305 static void sa1100_set_mctrl(struct uart_port *port, unsigned int mctrl)
307 struct sa1100_port *sport =
308 container_of(port, struct sa1100_port, port);
310 mctrl_gpio_set(sport->gpios, mctrl);
314 * Interrupts always disabled.
316 static void sa1100_break_ctl(struct uart_port *port, int break_state)
318 struct sa1100_port *sport =
319 container_of(port, struct sa1100_port, port);
323 spin_lock_irqsave(&sport->port.lock, flags);
324 utcr3 = UART_GET_UTCR3(sport);
325 if (break_state == -1)
329 UART_PUT_UTCR3(sport, utcr3);
330 spin_unlock_irqrestore(&sport->port.lock, flags);
333 static int sa1100_startup(struct uart_port *port)
335 struct sa1100_port *sport =
336 container_of(port, struct sa1100_port, port);
342 retval = request_irq(sport->port.irq, sa1100_int, 0,
343 "sa11x0-uart", sport);
348 * Finally, clear and enable interrupts
350 UART_PUT_UTSR0(sport, -1);
351 UART_PUT_UTCR3(sport, UTCR3_RXE | UTCR3_TXE | UTCR3_RIE);
354 * Enable modem status interrupts
356 spin_lock_irq(&sport->port.lock);
357 sa1100_enable_ms(&sport->port);
358 spin_unlock_irq(&sport->port.lock);
363 static void sa1100_shutdown(struct uart_port *port)
365 struct sa1100_port *sport =
366 container_of(port, struct sa1100_port, port);
371 del_timer_sync(&sport->timer);
376 free_irq(sport->port.irq, sport);
379 * Disable all interrupts, port and break condition.
381 UART_PUT_UTCR3(sport, 0);
385 sa1100_set_termios(struct uart_port *port, struct ktermios *termios,
386 const struct ktermios *old)
388 struct sa1100_port *sport =
389 container_of(port, struct sa1100_port, port);
391 unsigned int utcr0, old_utcr3, baud, quot;
392 unsigned int old_csize = old ? old->c_cflag & CSIZE : CS8;
395 * We only support CS7 and CS8.
397 while ((termios->c_cflag & CSIZE) != CS7 &&
398 (termios->c_cflag & CSIZE) != CS8) {
399 termios->c_cflag &= ~CSIZE;
400 termios->c_cflag |= old_csize;
404 if ((termios->c_cflag & CSIZE) == CS8)
409 if (termios->c_cflag & CSTOPB)
411 if (termios->c_cflag & PARENB) {
413 if (!(termios->c_cflag & PARODD))
418 * Ask the core to calculate the divisor for us.
420 baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16);
421 quot = uart_get_divisor(port, baud);
423 del_timer_sync(&sport->timer);
425 spin_lock_irqsave(&sport->port.lock, flags);
427 sport->port.read_status_mask &= UTSR0_TO_SM(UTSR0_TFS);
428 sport->port.read_status_mask |= UTSR1_TO_SM(UTSR1_ROR);
429 if (termios->c_iflag & INPCK)
430 sport->port.read_status_mask |=
431 UTSR1_TO_SM(UTSR1_FRE | UTSR1_PRE);
432 if (termios->c_iflag & (BRKINT | PARMRK))
433 sport->port.read_status_mask |=
434 UTSR0_TO_SM(UTSR0_RBB | UTSR0_REB);
437 * Characters to ignore
439 sport->port.ignore_status_mask = 0;
440 if (termios->c_iflag & IGNPAR)
441 sport->port.ignore_status_mask |=
442 UTSR1_TO_SM(UTSR1_FRE | UTSR1_PRE);
443 if (termios->c_iflag & IGNBRK) {
444 sport->port.ignore_status_mask |=
445 UTSR0_TO_SM(UTSR0_RBB | UTSR0_REB);
447 * If we're ignoring parity and break indicators,
448 * ignore overruns too (for real raw support).
450 if (termios->c_iflag & IGNPAR)
451 sport->port.ignore_status_mask |=
452 UTSR1_TO_SM(UTSR1_ROR);
456 * Update the per-port timeout.
458 uart_update_timeout(port, termios->c_cflag, baud);
461 * disable interrupts and drain transmitter
463 old_utcr3 = UART_GET_UTCR3(sport);
464 UART_PUT_UTCR3(sport, old_utcr3 & ~(UTCR3_RIE | UTCR3_TIE));
466 while (UART_GET_UTSR1(sport) & UTSR1_TBY)
469 /* then, disable everything */
470 UART_PUT_UTCR3(sport, 0);
472 /* set the parity, stop bits and data size */
473 UART_PUT_UTCR0(sport, utcr0);
475 /* set the baud rate */
477 UART_PUT_UTCR1(sport, ((quot & 0xf00) >> 8));
478 UART_PUT_UTCR2(sport, (quot & 0xff));
480 UART_PUT_UTSR0(sport, -1);
482 UART_PUT_UTCR3(sport, old_utcr3);
484 if (UART_ENABLE_MS(&sport->port, termios->c_cflag))
485 sa1100_enable_ms(&sport->port);
487 spin_unlock_irqrestore(&sport->port.lock, flags);
490 static const char *sa1100_type(struct uart_port *port)
492 struct sa1100_port *sport =
493 container_of(port, struct sa1100_port, port);
495 return sport->port.type == PORT_SA1100 ? "SA1100" : NULL;
499 * Release the memory region(s) being used by 'port'.
501 static void sa1100_release_port(struct uart_port *port)
503 struct sa1100_port *sport =
504 container_of(port, struct sa1100_port, port);
506 release_mem_region(sport->port.mapbase, UART_PORT_SIZE);
510 * Request the memory region(s) being used by 'port'.
512 static int sa1100_request_port(struct uart_port *port)
514 struct sa1100_port *sport =
515 container_of(port, struct sa1100_port, port);
517 return request_mem_region(sport->port.mapbase, UART_PORT_SIZE,
518 "sa11x0-uart") != NULL ? 0 : -EBUSY;
522 * Configure/autoconfigure the port.
524 static void sa1100_config_port(struct uart_port *port, int flags)
526 struct sa1100_port *sport =
527 container_of(port, struct sa1100_port, port);
529 if (flags & UART_CONFIG_TYPE &&
530 sa1100_request_port(&sport->port) == 0)
531 sport->port.type = PORT_SA1100;
535 * Verify the new serial_struct (for TIOCSSERIAL).
536 * The only change we allow are to the flags and type, and
537 * even then only between PORT_SA1100 and PORT_UNKNOWN
540 sa1100_verify_port(struct uart_port *port, struct serial_struct *ser)
542 struct sa1100_port *sport =
543 container_of(port, struct sa1100_port, port);
546 if (ser->type != PORT_UNKNOWN && ser->type != PORT_SA1100)
548 if (sport->port.irq != ser->irq)
550 if (ser->io_type != SERIAL_IO_MEM)
552 if (sport->port.uartclk / 16 != ser->baud_base)
554 if ((void *)sport->port.mapbase != ser->iomem_base)
556 if (sport->port.iobase != ser->port)
563 static struct uart_ops sa1100_pops = {
564 .tx_empty = sa1100_tx_empty,
565 .set_mctrl = sa1100_set_mctrl,
566 .get_mctrl = sa1100_get_mctrl,
567 .stop_tx = sa1100_stop_tx,
568 .start_tx = sa1100_start_tx,
569 .stop_rx = sa1100_stop_rx,
570 .enable_ms = sa1100_enable_ms,
571 .break_ctl = sa1100_break_ctl,
572 .startup = sa1100_startup,
573 .shutdown = sa1100_shutdown,
574 .set_termios = sa1100_set_termios,
576 .release_port = sa1100_release_port,
577 .request_port = sa1100_request_port,
578 .config_port = sa1100_config_port,
579 .verify_port = sa1100_verify_port,
582 static struct sa1100_port sa1100_ports[NR_PORTS];
585 * Setup the SA1100 serial ports. Note that we don't include the IrDA
586 * port here since we have our own SIR/FIR driver (see drivers/net/irda)
588 * Note also that we support "console=ttySAx" where "x" is either 0 or 1.
589 * Which serial port this ends up being depends on the machine you're
590 * running this kernel on. I'm not convinced that this is a good idea,
591 * but that's the way it traditionally works.
593 * Note that NanoEngine UART3 becomes UART2, and UART2 is no longer
596 static void __init sa1100_init_ports(void)
598 static int first = 1;
605 for (i = 0; i < NR_PORTS; i++) {
606 sa1100_ports[i].port.uartclk = 3686400;
607 sa1100_ports[i].port.ops = &sa1100_pops;
608 sa1100_ports[i].port.fifosize = 8;
609 sa1100_ports[i].port.line = i;
610 sa1100_ports[i].port.iotype = UPIO_MEM;
611 timer_setup(&sa1100_ports[i].timer, sa1100_timeout, 0);
615 * make transmit lines outputs, so that when the port
616 * is closed, the output is in the MARK state.
618 PPDR |= PPC_TXD1 | PPC_TXD3;
619 PPSR |= PPC_TXD1 | PPC_TXD3;
622 void sa1100_register_uart_fns(struct sa1100_port_fns *fns)
625 sa1100_pops.get_mctrl = fns->get_mctrl;
627 sa1100_pops.set_mctrl = fns->set_mctrl;
629 sa1100_pops.pm = fns->pm;
631 * FIXME: fns->set_wake is unused - this should be called from
632 * the suspend() callback if device_may_wakeup(dev)) is set.
636 void __init sa1100_register_uart(int idx, int port)
638 if (idx >= NR_PORTS) {
639 printk(KERN_ERR "%s: bad index number %d\n", __func__, idx);
645 sa1100_ports[idx].port.membase = (void __iomem *)&Ser1UTCR0;
646 sa1100_ports[idx].port.mapbase = _Ser1UTCR0;
647 sa1100_ports[idx].port.irq = IRQ_Ser1UART;
648 sa1100_ports[idx].port.flags = UPF_BOOT_AUTOCONF;
652 sa1100_ports[idx].port.membase = (void __iomem *)&Ser2UTCR0;
653 sa1100_ports[idx].port.mapbase = _Ser2UTCR0;
654 sa1100_ports[idx].port.irq = IRQ_Ser2ICP;
655 sa1100_ports[idx].port.flags = UPF_BOOT_AUTOCONF;
659 sa1100_ports[idx].port.membase = (void __iomem *)&Ser3UTCR0;
660 sa1100_ports[idx].port.mapbase = _Ser3UTCR0;
661 sa1100_ports[idx].port.irq = IRQ_Ser3UART;
662 sa1100_ports[idx].port.flags = UPF_BOOT_AUTOCONF;
666 printk(KERN_ERR "%s: bad port number %d\n", __func__, port);
671 #ifdef CONFIG_SERIAL_SA1100_CONSOLE
672 static void sa1100_console_putchar(struct uart_port *port, unsigned char ch)
674 struct sa1100_port *sport =
675 container_of(port, struct sa1100_port, port);
677 while (!(UART_GET_UTSR1(sport) & UTSR1_TNF))
679 UART_PUT_CHAR(sport, ch);
683 * Interrupts are disabled on entering
686 sa1100_console_write(struct console *co, const char *s, unsigned int count)
688 struct sa1100_port *sport = &sa1100_ports[co->index];
689 unsigned int old_utcr3, status;
692 * First, save UTCR3 and then disable interrupts
694 old_utcr3 = UART_GET_UTCR3(sport);
695 UART_PUT_UTCR3(sport, (old_utcr3 & ~(UTCR3_RIE | UTCR3_TIE)) |
698 uart_console_write(&sport->port, s, count, sa1100_console_putchar);
701 * Finally, wait for transmitter to become empty
705 status = UART_GET_UTSR1(sport);
706 } while (status & UTSR1_TBY);
707 UART_PUT_UTCR3(sport, old_utcr3);
711 * If the port was already initialised (eg, by a boot loader),
712 * try to determine the current setup.
715 sa1100_console_get_options(struct sa1100_port *sport, int *baud,
716 int *parity, int *bits)
720 utcr3 = UART_GET_UTCR3(sport) & (UTCR3_RXE | UTCR3_TXE);
721 if (utcr3 == (UTCR3_RXE | UTCR3_TXE)) {
722 /* ok, the port was enabled */
723 unsigned int utcr0, quot;
725 utcr0 = UART_GET_UTCR0(sport);
728 if (utcr0 & UTCR0_PE) {
729 if (utcr0 & UTCR0_OES)
735 if (utcr0 & UTCR0_DSS)
740 quot = UART_GET_UTCR2(sport) | UART_GET_UTCR1(sport) << 8;
742 *baud = sport->port.uartclk / (16 * (quot + 1));
747 sa1100_console_setup(struct console *co, char *options)
749 struct sa1100_port *sport;
756 * Check whether an invalid uart number has been specified, and
757 * if so, search for the first available port that does have
760 if (co->index == -1 || co->index >= NR_PORTS)
762 sport = &sa1100_ports[co->index];
765 uart_parse_options(options, &baud, &parity, &bits, &flow);
767 sa1100_console_get_options(sport, &baud, &parity, &bits);
769 return uart_set_options(&sport->port, co, baud, parity, bits, flow);
772 static struct uart_driver sa1100_reg;
773 static struct console sa1100_console = {
775 .write = sa1100_console_write,
776 .device = uart_console_device,
777 .setup = sa1100_console_setup,
778 .flags = CON_PRINTBUFFER,
783 static int __init sa1100_rs_console_init(void)
786 register_console(&sa1100_console);
789 console_initcall(sa1100_rs_console_init);
791 #define SA1100_CONSOLE &sa1100_console
793 #define SA1100_CONSOLE NULL
796 static struct uart_driver sa1100_reg = {
797 .owner = THIS_MODULE,
798 .driver_name = "ttySA",
800 .major = SERIAL_SA1100_MAJOR,
801 .minor = MINOR_START,
803 .cons = SA1100_CONSOLE,
806 static int sa1100_serial_suspend(struct platform_device *dev, pm_message_t state)
808 struct sa1100_port *sport = platform_get_drvdata(dev);
811 uart_suspend_port(&sa1100_reg, &sport->port);
816 static int sa1100_serial_resume(struct platform_device *dev)
818 struct sa1100_port *sport = platform_get_drvdata(dev);
821 uart_resume_port(&sa1100_reg, &sport->port);
826 static int sa1100_serial_add_one_port(struct sa1100_port *sport, struct platform_device *dev)
828 sport->port.dev = &dev->dev;
829 sport->port.has_sysrq = IS_ENABLED(CONFIG_SERIAL_SA1100_CONSOLE);
831 // mctrl_gpio_init() requires that the GPIO driver supports interrupts,
832 // but we need to support GPIO drivers for hardware that has no such
833 // interrupts. Use mctrl_gpio_init_noauto() instead.
834 sport->gpios = mctrl_gpio_init_noauto(sport->port.dev, 0);
835 if (IS_ERR(sport->gpios)) {
836 int err = PTR_ERR(sport->gpios);
838 dev_err(sport->port.dev, "failed to get mctrl gpios: %d\n",
841 if (err == -EPROBE_DEFER)
847 platform_set_drvdata(dev, sport);
849 return uart_add_one_port(&sa1100_reg, &sport->port);
852 static int sa1100_serial_probe(struct platform_device *dev)
854 struct resource *res;
857 res = platform_get_resource(dev, IORESOURCE_MEM, 0);
861 for (i = 0; i < NR_PORTS; i++)
862 if (sa1100_ports[i].port.mapbase == res->start)
867 sa1100_serial_add_one_port(&sa1100_ports[i], dev);
872 static int sa1100_serial_remove(struct platform_device *pdev)
874 struct sa1100_port *sport = platform_get_drvdata(pdev);
877 uart_remove_one_port(&sa1100_reg, &sport->port);
882 static struct platform_driver sa11x0_serial_driver = {
883 .probe = sa1100_serial_probe,
884 .remove = sa1100_serial_remove,
885 .suspend = sa1100_serial_suspend,
886 .resume = sa1100_serial_resume,
888 .name = "sa11x0-uart",
892 static int __init sa1100_serial_init(void)
896 printk(KERN_INFO "Serial: SA11x0 driver\n");
900 ret = uart_register_driver(&sa1100_reg);
902 ret = platform_driver_register(&sa11x0_serial_driver);
904 uart_unregister_driver(&sa1100_reg);
909 static void __exit sa1100_serial_exit(void)
911 platform_driver_unregister(&sa11x0_serial_driver);
912 uart_unregister_driver(&sa1100_reg);
915 module_init(sa1100_serial_init);
916 module_exit(sa1100_serial_exit);
918 MODULE_AUTHOR("Deep Blue Solutions Ltd");
919 MODULE_DESCRIPTION("SA1100 generic serial port driver");
920 MODULE_LICENSE("GPL");
921 MODULE_ALIAS_CHARDEV_MAJOR(SERIAL_SA1100_MAJOR);
922 MODULE_ALIAS("platform:sa11x0-uart");