drivers/spi/spi-cadence.c

   1 // SPDX-License-Identifier: GPL-2.0-or-later
   2 /*
   3  * Cadence SPI controller driver (master mode only)
   4  *
   5  * Copyright (C) 2008 - 2014 Xilinx, Inc.
   6  *
   7  * based on Blackfin On-Chip SPI Driver (spi_bfin5xx.c)
   8  */
   9
  10 #include <linux/clk.h>
  11 #include <linux/delay.h>
  12 #include <linux/gpio/consumer.h>
  13 #include <linux/interrupt.h>
  14 #include <linux/io.h>
  15 #include <linux/module.h>
  16 #include <linux/of_irq.h>
  17 #include <linux/of_address.h>
  18 #include <linux/platform_device.h>
  19 #include <linux/pm_runtime.h>
  20 #include <linux/spi/spi.h>
  21
  22 /* Name of this driver */
  23 #define CDNS_SPI_NAME           "cdns-spi"
  24
  25 /* Register offset definitions */
  26 #define CDNS_SPI_CR     0x00 /* Configuration  Register, RW */
  27 #define CDNS_SPI_ISR    0x04 /* Interrupt Status Register, RO */
  28 #define CDNS_SPI_IER    0x08 /* Interrupt Enable Register, WO */
  29 #define CDNS_SPI_IDR    0x0c /* Interrupt Disable Register, WO */
  30 #define CDNS_SPI_IMR    0x10 /* Interrupt Enabled Mask Register, RO */
  31 #define CDNS_SPI_ER     0x14 /* Enable/Disable Register, RW */
  32 #define CDNS_SPI_DR     0x18 /* Delay Register, RW */
  33 #define CDNS_SPI_TXD    0x1C /* Data Transmit Register, WO */
  34 #define CDNS_SPI_RXD    0x20 /* Data Receive Register, RO */
  35 #define CDNS_SPI_SICR   0x24 /* Slave Idle Count Register, RW */
  36 #define CDNS_SPI_THLD   0x28 /* Transmit FIFO Watermark Register,RW */
  37
  38 #define SPI_AUTOSUSPEND_TIMEOUT         3000
  39 /*
  40  * SPI Configuration Register bit Masks
  41  *
  42  * This register contains various control bits that affect the operation
  43  * of the SPI controller
  44  */
  45 #define CDNS_SPI_CR_MANSTRT     0x00010000 /* Manual TX Start */
  46 #define CDNS_SPI_CR_CPHA                0x00000004 /* Clock Phase Control */
  47 #define CDNS_SPI_CR_CPOL                0x00000002 /* Clock Polarity Control */
  48 #define CDNS_SPI_CR_SSCTRL              0x00003C00 /* Slave Select Mask */
  49 #define CDNS_SPI_CR_PERI_SEL    0x00000200 /* Peripheral Select Decode */
  50 #define CDNS_SPI_CR_BAUD_DIV    0x00000038 /* Baud Rate Divisor Mask */
  51 #define CDNS_SPI_CR_MSTREN              0x00000001 /* Master Enable Mask */
  52 #define CDNS_SPI_CR_MANSTRTEN   0x00008000 /* Manual TX Enable Mask */
  53 #define CDNS_SPI_CR_SSFORCE     0x00004000 /* Manual SS Enable Mask */
  54 #define CDNS_SPI_CR_BAUD_DIV_4  0x00000008 /* Default Baud Div Mask */
  55 #define CDNS_SPI_CR_DEFAULT     (CDNS_SPI_CR_MSTREN | \
  56                                         CDNS_SPI_CR_SSCTRL | \
  57                                         CDNS_SPI_CR_SSFORCE | \
  58                                         CDNS_SPI_CR_BAUD_DIV_4)
  59
  60 /*
  61  * SPI Configuration Register - Baud rate and slave select
  62  *
  63  * These are the values used in the calculation of baud rate divisor and
  64  * setting the slave select.
  65  */
  66
  67 #define CDNS_SPI_BAUD_DIV_MAX           7 /* Baud rate divisor maximum */
  68 #define CDNS_SPI_BAUD_DIV_MIN           1 /* Baud rate divisor minimum */
  69 #define CDNS_SPI_BAUD_DIV_SHIFT         3 /* Baud rate divisor shift in CR */
  70 #define CDNS_SPI_SS_SHIFT               10 /* Slave Select field shift in CR */
  71 #define CDNS_SPI_SS0                    0x1 /* Slave Select zero */
  72
  73 /*
  74  * SPI Interrupt Registers bit Masks
  75  *
  76  * All the four interrupt registers (Status/Mask/Enable/Disable) have the same
  77  * bit definitions.
  78  */
  79 #define CDNS_SPI_IXR_TXOW       0x00000004 /* SPI TX FIFO Overwater */
  80 #define CDNS_SPI_IXR_MODF       0x00000002 /* SPI Mode Fault */
  81 #define CDNS_SPI_IXR_RXNEMTY 0x00000010 /* SPI RX FIFO Not Empty */
  82 #define CDNS_SPI_IXR_DEFAULT    (CDNS_SPI_IXR_TXOW | \
  83                                         CDNS_SPI_IXR_MODF)
  84 #define CDNS_SPI_IXR_TXFULL     0x00000008 /* SPI TX Full */
  85 #define CDNS_SPI_IXR_ALL        0x0000007F /* SPI all interrupts */
  86
  87 /*
  88  * SPI Enable Register bit Masks
  89  *
  90  * This register is used to enable or disable the SPI controller
  91  */
  92 #define CDNS_SPI_ER_ENABLE      0x00000001 /* SPI Enable Bit Mask */
  93 #define CDNS_SPI_ER_DISABLE     0x0 /* SPI Disable Bit Mask */
  94
  95 /* SPI FIFO depth in bytes */
  96 #define CDNS_SPI_FIFO_DEPTH     128
  97
  98 /* Default number of chip select lines */
  99 #define CDNS_SPI_DEFAULT_NUM_CS         4
 100
 101 /**
 102  * struct cdns_spi - This definition defines spi driver instance
 103  * @regs:               Virtual address of the SPI controller registers
 104  * @ref_clk:            Pointer to the peripheral clock
 105  * @pclk:               Pointer to the APB clock
 106  * @speed_hz:           Current SPI bus clock speed in Hz
 107  * @txbuf:              Pointer to the TX buffer
 108  * @rxbuf:              Pointer to the RX buffer
 109  * @tx_bytes:           Number of bytes left to transfer
 110  * @rx_bytes:           Number of bytes requested
 111  * @dev_busy:           Device busy flag
 112  * @is_decoded_cs:      Flag for decoder property set or not
 113  */
 114 struct cdns_spi {
 115         void __iomem *regs;
 116         struct clk *ref_clk;
 117         struct clk *pclk;
 118         unsigned int clk_rate;
 119         u32 speed_hz;
 120         const u8 *txbuf;
 121         u8 *rxbuf;
 122         int tx_bytes;
 123         int rx_bytes;
 124         u8 dev_busy;
 125         u32 is_decoded_cs;
 126 };
 127
 128 /* Macros for the SPI controller read/write */
 129 static inline u32 cdns_spi_read(struct cdns_spi *xspi, u32 offset)
 130 {
 131         return readl_relaxed(xspi->regs + offset);
 132 }
 133
 134 static inline void cdns_spi_write(struct cdns_spi *xspi, u32 offset, u32 val)
 135 {
 136         writel_relaxed(val, xspi->regs + offset);
 137 }
 138
 139 /**
 140  * cdns_spi_init_hw - Initialize the hardware and configure the SPI controller
 141  * @xspi:       Pointer to the cdns_spi structure
 142  *
 143  * On reset the SPI controller is configured to be in master mode, baud rate
 144  * divisor is set to 4, threshold value for TX FIFO not full interrupt is set
 145  * to 1 and size of the word to be transferred as 8 bit.
 146  * This function initializes the SPI controller to disable and clear all the
 147  * interrupts, enable manual slave select and manual start, deselect all the
 148  * chip select lines, and enable the SPI controller.
 149  */
 150 static void cdns_spi_init_hw(struct cdns_spi *xspi)
 151 {
 152         u32 ctrl_reg = CDNS_SPI_CR_DEFAULT;
 153
 154         if (xspi->is_decoded_cs)
 155                 ctrl_reg |= CDNS_SPI_CR_PERI_SEL;
 156
 157         cdns_spi_write(xspi, CDNS_SPI_ER, CDNS_SPI_ER_DISABLE);
 158         cdns_spi_write(xspi, CDNS_SPI_IDR, CDNS_SPI_IXR_ALL);
 159
 160         /* Clear the RX FIFO */
 161         while (cdns_spi_read(xspi, CDNS_SPI_ISR) & CDNS_SPI_IXR_RXNEMTY)
 162                 cdns_spi_read(xspi, CDNS_SPI_RXD);
 163
 164         cdns_spi_write(xspi, CDNS_SPI_ISR, CDNS_SPI_IXR_ALL);
 165         cdns_spi_write(xspi, CDNS_SPI_CR, ctrl_reg);
 166         cdns_spi_write(xspi, CDNS_SPI_ER, CDNS_SPI_ER_ENABLE);
 167 }
 168
 169 /**
 170  * cdns_spi_chipselect - Select or deselect the chip select line
 171  * @spi:        Pointer to the spi_device structure
 172  * @is_high:    Select(0) or deselect (1) the chip select line
 173  */
 174 static void cdns_spi_chipselect(struct spi_device *spi, bool is_high)
 175 {
 176         struct cdns_spi *xspi = spi_master_get_devdata(spi->master);
 177         u32 ctrl_reg;
 178
 179         ctrl_reg = cdns_spi_read(xspi, CDNS_SPI_CR);
 180
 181         if (is_high) {
 182                 /* Deselect the slave */
 183                 ctrl_reg |= CDNS_SPI_CR_SSCTRL;
 184         } else {
 185                 /* Select the slave */
 186                 ctrl_reg &= ~CDNS_SPI_CR_SSCTRL;
 187                 if (!(xspi->is_decoded_cs))
 188                         ctrl_reg |= ((~(CDNS_SPI_SS0 << spi->chip_select)) <<
 189                                      CDNS_SPI_SS_SHIFT) &
 190                                      CDNS_SPI_CR_SSCTRL;
 191                 else
 192                         ctrl_reg |= (spi->chip_select << CDNS_SPI_SS_SHIFT) &
 193                                      CDNS_SPI_CR_SSCTRL;
 194         }
 195
 196         cdns_spi_write(xspi, CDNS_SPI_CR, ctrl_reg);
 197 }
 198
 199 /**
 200  * cdns_spi_config_clock_mode - Sets clock polarity and phase
 201  * @spi:        Pointer to the spi_device structure
 202  *
 203  * Sets the requested clock polarity and phase.
 204  */
 205 static void cdns_spi_config_clock_mode(struct spi_device *spi)
 206 {
 207         struct cdns_spi *xspi = spi_master_get_devdata(spi->master);
 208         u32 ctrl_reg, new_ctrl_reg;
 209
 210         new_ctrl_reg = cdns_spi_read(xspi, CDNS_SPI_CR);
 211         ctrl_reg = new_ctrl_reg;
 212
 213         /* Set the SPI clock phase and clock polarity */
 214         new_ctrl_reg &= ~(CDNS_SPI_CR_CPHA | CDNS_SPI_CR_CPOL);
 215         if (spi->mode & SPI_CPHA)
 216                 new_ctrl_reg |= CDNS_SPI_CR_CPHA;
 217         if (spi->mode & SPI_CPOL)
 218                 new_ctrl_reg |= CDNS_SPI_CR_CPOL;
 219
 220         if (new_ctrl_reg != ctrl_reg) {
 221                 /*
 222                  * Just writing the CR register does not seem to apply the clock
 223                  * setting changes. This is problematic when changing the clock
 224                  * polarity as it will cause the SPI slave to see spurious clock
 225                  * transitions. To workaround the issue toggle the ER register.
 226                  */
 227                 cdns_spi_write(xspi, CDNS_SPI_ER, CDNS_SPI_ER_DISABLE);
 228                 cdns_spi_write(xspi, CDNS_SPI_CR, new_ctrl_reg);
 229                 cdns_spi_write(xspi, CDNS_SPI_ER, CDNS_SPI_ER_ENABLE);
 230         }
 231 }
 232
 233 /**
 234  * cdns_spi_config_clock_freq - Sets clock frequency
 235  * @spi:        Pointer to the spi_device structure
 236  * @transfer:   Pointer to the spi_transfer structure which provides
 237  *              information about next transfer setup parameters
 238  *
 239  * Sets the requested clock frequency.
 240  * Note: If the requested frequency is not an exact match with what can be
 241  * obtained using the prescalar value the driver sets the clock frequency which
 242  * is lower than the requested frequency (maximum lower) for the transfer. If
 243  * the requested frequency is higher or lower than that is supported by the SPI
 244  * controller the driver will set the highest or lowest frequency supported by
 245  * controller.
 246  */
 247 static void cdns_spi_config_clock_freq(struct spi_device *spi,
 248                                        struct spi_transfer *transfer)
 249 {
 250         struct cdns_spi *xspi = spi_master_get_devdata(spi->master);
 251         u32 ctrl_reg, baud_rate_val;
 252         unsigned long frequency;
 253
 254         frequency = xspi->clk_rate;
 255
 256         ctrl_reg = cdns_spi_read(xspi, CDNS_SPI_CR);
 257
 258         /* Set the clock frequency */
 259         if (xspi->speed_hz != transfer->speed_hz) {
 260                 /* first valid value is 1 */
 261                 baud_rate_val = CDNS_SPI_BAUD_DIV_MIN;
 262                 while ((baud_rate_val < CDNS_SPI_BAUD_DIV_MAX) &&
 263                        (frequency / (2 << baud_rate_val)) > transfer->speed_hz)
 264                         baud_rate_val++;
 265
 266                 ctrl_reg &= ~CDNS_SPI_CR_BAUD_DIV;
 267                 ctrl_reg |= baud_rate_val << CDNS_SPI_BAUD_DIV_SHIFT;
 268
 269                 xspi->speed_hz = frequency / (2 << baud_rate_val);
 270         }
 271         cdns_spi_write(xspi, CDNS_SPI_CR, ctrl_reg);
 272 }
 273
 274 /**
 275  * cdns_spi_setup_transfer - Configure SPI controller for specified transfer
 276  * @spi:        Pointer to the spi_device structure
 277  * @transfer:   Pointer to the spi_transfer structure which provides
 278  *              information about next transfer setup parameters
 279  *
 280  * Sets the operational mode of SPI controller for the next SPI transfer and
 281  * sets the requested clock frequency.
 282  *
 283  * Return:      Always 0
 284  */
 285 static int cdns_spi_setup_transfer(struct spi_device *spi,
 286                                    struct spi_transfer *transfer)
 287 {
 288         struct cdns_spi *xspi = spi_master_get_devdata(spi->master);
 289
 290         cdns_spi_config_clock_freq(spi, transfer);
 291
 292         dev_dbg(&spi->dev, "%s, mode %d, %u bits/w, %u clock speed\n",
 293                 __func__, spi->mode, spi->bits_per_word,
 294                 xspi->speed_hz);
 295
 296         return 0;
 297 }
 298
 299 /**
 300  * cdns_spi_fill_tx_fifo - Fills the TX FIFO with as many bytes as possible
 301  * @xspi:       Pointer to the cdns_spi structure
 302  */
 303 static void cdns_spi_fill_tx_fifo(struct cdns_spi *xspi)
 304 {
 305         unsigned long trans_cnt = 0;
 306
 307         while ((trans_cnt < CDNS_SPI_FIFO_DEPTH) &&
 308                (xspi->tx_bytes > 0)) {
 309
 310                 /* When xspi in busy condition, bytes may send failed,
 311                  * then spi control did't work thoroughly, add one byte delay
 312                  */
 313                 if (cdns_spi_read(xspi, CDNS_SPI_ISR) &
 314                     CDNS_SPI_IXR_TXFULL)
 315                         udelay(10);
 316
 317                 if (xspi->txbuf)
 318                         cdns_spi_write(xspi, CDNS_SPI_TXD, *xspi->txbuf++);
 319                 else
 320                         cdns_spi_write(xspi, CDNS_SPI_TXD, 0);
 321
 322                 xspi->tx_bytes--;
 323                 trans_cnt++;
 324         }
 325 }
 326
 327 /**
 328  * cdns_spi_irq - Interrupt service routine of the SPI controller
 329  * @irq:        IRQ number
 330  * @dev_id:     Pointer to the xspi structure
 331  *
 332  * This function handles TX empty and Mode Fault interrupts only.
 333  * On TX empty interrupt this function reads the received data from RX FIFO and
 334  * fills the TX FIFO if there is any data remaining to be transferred.
 335  * On Mode Fault interrupt this function indicates that transfer is completed,
 336  * the SPI subsystem will identify the error as the remaining bytes to be
 337  * transferred is non-zero.
 338  *
 339  * Return:      IRQ_HANDLED when handled; IRQ_NONE otherwise.
 340  */
 341 static irqreturn_t cdns_spi_irq(int irq, void *dev_id)
 342 {
 343         struct spi_master *master = dev_id;
 344         struct cdns_spi *xspi = spi_master_get_devdata(master);
 345         irqreturn_t status;
 346         u32 intr_status;
 347
 348         status = IRQ_NONE;
 349         intr_status = cdns_spi_read(xspi, CDNS_SPI_ISR);
 350         cdns_spi_write(xspi, CDNS_SPI_ISR, intr_status);
 351
 352         if (intr_status & CDNS_SPI_IXR_MODF) {
 353                 /* Indicate that transfer is completed, the SPI subsystem will
 354                  * identify the error as the remaining bytes to be
 355                  * transferred is non-zero
 356                  */
 357                 cdns_spi_write(xspi, CDNS_SPI_IDR, CDNS_SPI_IXR_DEFAULT);
 358                 spi_finalize_current_transfer(master);
 359                 status = IRQ_HANDLED;
 360         } else if (intr_status & CDNS_SPI_IXR_TXOW) {
 361                 unsigned long trans_cnt;
 362
 363                 trans_cnt = xspi->rx_bytes - xspi->tx_bytes;
 364
 365                 /* Read out the data from the RX FIFO */
 366                 while (trans_cnt) {
 367                         u8 data;
 368
 369                         data = cdns_spi_read(xspi, CDNS_SPI_RXD);
 370                         if (xspi->rxbuf)
 371                                 *xspi->rxbuf++ = data;
 372
 373                         xspi->rx_bytes--;
 374                         trans_cnt--;
 375                 }
 376
 377                 if (xspi->tx_bytes) {
 378                         /* There is more data to send */
 379                         cdns_spi_fill_tx_fifo(xspi);
 380                 } else {
 381                         /* Transfer is completed */
 382                         cdns_spi_write(xspi, CDNS_SPI_IDR,
 383                                        CDNS_SPI_IXR_DEFAULT);
 384                         spi_finalize_current_transfer(master);
 385                 }
 386                 status = IRQ_HANDLED;
 387         }
 388
 389         return status;
 390 }
 391
 392 static int cdns_prepare_message(struct spi_master *master,
 393                                 struct spi_message *msg)
 394 {
 395         cdns_spi_config_clock_mode(msg->spi);
 396         return 0;
 397 }
 398
 399 /**
 400  * cdns_transfer_one - Initiates the SPI transfer
 401  * @master:     Pointer to spi_master structure
 402  * @spi:        Pointer to the spi_device structure
 403  * @transfer:   Pointer to the spi_transfer structure which provides
 404  *              information about next transfer parameters
 405  *
 406  * This function fills the TX FIFO, starts the SPI transfer and
 407  * returns a positive transfer count so that core will wait for completion.
 408  *
 409  * Return:      Number of bytes transferred in the last transfer
 410  */
 411 static int cdns_transfer_one(struct spi_master *master,
 412                              struct spi_device *spi,
 413                              struct spi_transfer *transfer)
 414 {
 415         struct cdns_spi *xspi = spi_master_get_devdata(master);
 416
 417         xspi->txbuf = transfer->tx_buf;
 418         xspi->rxbuf = transfer->rx_buf;
 419         xspi->tx_bytes = transfer->len;
 420         xspi->rx_bytes = transfer->len;
 421
 422         cdns_spi_setup_transfer(spi, transfer);
 423         cdns_spi_fill_tx_fifo(xspi);
 424         spi_transfer_delay_exec(transfer);
 425
 426         cdns_spi_write(xspi, CDNS_SPI_IER, CDNS_SPI_IXR_DEFAULT);
 427         return transfer->len;
 428 }
 429
 430 /**
 431  * cdns_prepare_transfer_hardware - Prepares hardware for transfer.
 432  * @master:     Pointer to the spi_master structure which provides
 433  *              information about the controller.
 434  *
 435  * This function enables SPI master controller.
 436  *
 437  * Return:      0 always
 438  */
 439 static int cdns_prepare_transfer_hardware(struct spi_master *master)
 440 {
 441         struct cdns_spi *xspi = spi_master_get_devdata(master);
 442
 443         cdns_spi_write(xspi, CDNS_SPI_ER, CDNS_SPI_ER_ENABLE);
 444
 445         return 0;
 446 }
 447
 448 /**
 449  * cdns_unprepare_transfer_hardware - Relaxes hardware after transfer
 450  * @master:     Pointer to the spi_master structure which provides
 451  *              information about the controller.
 452  *
 453  * This function disables the SPI master controller.
 454  *
 455  * Return:      0 always
 456  */
 457 static int cdns_unprepare_transfer_hardware(struct spi_master *master)
 458 {
 459         struct cdns_spi *xspi = spi_master_get_devdata(master);
 460
 461         cdns_spi_write(xspi, CDNS_SPI_ER, CDNS_SPI_ER_DISABLE);
 462
 463         return 0;
 464 }
 465
 466 /**
 467  * cdns_spi_probe - Probe method for the SPI driver
 468  * @pdev:       Pointer to the platform_device structure
 469  *
 470  * This function initializes the driver data structures and the hardware.
 471  *
 472  * Return:      0 on success and error value on error
 473  */
 474 static int cdns_spi_probe(struct platform_device *pdev)
 475 {
 476         int ret = 0, irq;
 477         struct spi_master *master;
 478         struct cdns_spi *xspi;
 479         u32 num_cs;
 480
 481         master = spi_alloc_master(&pdev->dev, sizeof(*xspi));
 482         if (!master)
 483                 return -ENOMEM;
 484
 485         xspi = spi_master_get_devdata(master);
 486         master->dev.of_node = pdev->dev.of_node;
 487         platform_set_drvdata(pdev, master);
 488
 489         xspi->regs = devm_platform_ioremap_resource(pdev, 0);
 490         if (IS_ERR(xspi->regs)) {
 491                 ret = PTR_ERR(xspi->regs);
 492                 goto remove_master;
 493         }
 494
 495         xspi->pclk = devm_clk_get(&pdev->dev, "pclk");
 496         if (IS_ERR(xspi->pclk)) {
 497                 dev_err(&pdev->dev, "pclk clock not found.\n");
 498                 ret = PTR_ERR(xspi->pclk);
 499                 goto remove_master;
 500         }
 501
 502         xspi->ref_clk = devm_clk_get(&pdev->dev, "ref_clk");
 503         if (IS_ERR(xspi->ref_clk)) {
 504                 dev_err(&pdev->dev, "ref_clk clock not found.\n");
 505                 ret = PTR_ERR(xspi->ref_clk);
 506                 goto remove_master;
 507         }
 508
 509         ret = clk_prepare_enable(xspi->pclk);
 510         if (ret) {
 511                 dev_err(&pdev->dev, "Unable to enable APB clock.\n");
 512                 goto remove_master;
 513         }
 514
 515         ret = clk_prepare_enable(xspi->ref_clk);
 516         if (ret) {
 517                 dev_err(&pdev->dev, "Unable to enable device clock.\n");
 518                 goto clk_dis_apb;
 519         }
 520
 521         pm_runtime_use_autosuspend(&pdev->dev);
 522         pm_runtime_set_autosuspend_delay(&pdev->dev, SPI_AUTOSUSPEND_TIMEOUT);
 523         pm_runtime_get_noresume(&pdev->dev);
 524         pm_runtime_set_active(&pdev->dev);
 525         pm_runtime_enable(&pdev->dev);
 526
 527         ret = of_property_read_u32(pdev->dev.of_node, "num-cs", &num_cs);
 528         if (ret < 0)
 529                 master->num_chipselect = CDNS_SPI_DEFAULT_NUM_CS;
 530         else
 531                 master->num_chipselect = num_cs;
 532
 533         ret = of_property_read_u32(pdev->dev.of_node, "is-decoded-cs",
 534                                    &xspi->is_decoded_cs);
 535         if (ret < 0)
 536                 xspi->is_decoded_cs = 0;
 537
 538         /* SPI controller initializations */
 539         cdns_spi_init_hw(xspi);
 540
 541         irq = platform_get_irq(pdev, 0);
 542         if (irq <= 0) {
 543                 ret = -ENXIO;
 544                 goto clk_dis_all;
 545         }
 546
 547         ret = devm_request_irq(&pdev->dev, irq, cdns_spi_irq,
 548                                0, pdev->name, master);
 549         if (ret != 0) {
 550                 ret = -ENXIO;
 551                 dev_err(&pdev->dev, "request_irq failed\n");
 552                 goto clk_dis_all;
 553         }
 554
 555         master->use_gpio_descriptors = true;
 556         master->prepare_transfer_hardware = cdns_prepare_transfer_hardware;
 557         master->prepare_message = cdns_prepare_message;
 558         master->transfer_one = cdns_transfer_one;
 559         master->unprepare_transfer_hardware = cdns_unprepare_transfer_hardware;
 560         master->set_cs = cdns_spi_chipselect;
 561         master->auto_runtime_pm = true;
 562         master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH;
 563
 564         xspi->clk_rate = clk_get_rate(xspi->ref_clk);
 565         /* Set to default valid value */
 566         master->max_speed_hz = xspi->clk_rate / 4;
 567         xspi->speed_hz = master->max_speed_hz;
 568
 569         master->bits_per_word_mask = SPI_BPW_MASK(8);
 570
 571         pm_runtime_mark_last_busy(&pdev->dev);
 572         pm_runtime_put_autosuspend(&pdev->dev);
 573
 574         ret = spi_register_master(master);
 575         if (ret) {
 576                 dev_err(&pdev->dev, "spi_register_master failed\n");
 577                 goto clk_dis_all;
 578         }
 579
 580         return ret;
 581
 582 clk_dis_all:
 583         pm_runtime_set_suspended(&pdev->dev);
 584         pm_runtime_disable(&pdev->dev);
 585         clk_disable_unprepare(xspi->ref_clk);
 586 clk_dis_apb:
 587         clk_disable_unprepare(xspi->pclk);
 588 remove_master:
 589         spi_master_put(master);
 590         return ret;
 591 }
 592
 593 /**
 594  * cdns_spi_remove - Remove method for the SPI driver
 595  * @pdev:       Pointer to the platform_device structure
 596  *
 597  * This function is called if a device is physically removed from the system or
 598  * if the driver module is being unloaded. It frees all resources allocated to
 599  * the device.
 600  *
 601  * Return:      0 on success and error value on error
 602  */
 603 static int cdns_spi_remove(struct platform_device *pdev)
 604 {
 605         struct spi_master *master = platform_get_drvdata(pdev);
 606         struct cdns_spi *xspi = spi_master_get_devdata(master);
 607
 608         cdns_spi_write(xspi, CDNS_SPI_ER, CDNS_SPI_ER_DISABLE);
 609
 610         clk_disable_unprepare(xspi->ref_clk);
 611         clk_disable_unprepare(xspi->pclk);
 612         pm_runtime_set_suspended(&pdev->dev);
 613         pm_runtime_disable(&pdev->dev);
 614
 615         spi_unregister_master(master);
 616
 617         return 0;
 618 }
 619
 620 /**
 621  * cdns_spi_suspend - Suspend method for the SPI driver
 622  * @dev:        Address of the platform_device structure
 623  *
 624  * This function disables the SPI controller and
 625  * changes the driver state to "suspend"
 626  *
 627  * Return:      0 on success and error value on error
 628  */
 629 static int __maybe_unused cdns_spi_suspend(struct device *dev)
 630 {
 631         struct spi_master *master = dev_get_drvdata(dev);
 632
 633         return spi_master_suspend(master);
 634 }
 635
 636 /**
 637  * cdns_spi_resume - Resume method for the SPI driver
 638  * @dev:        Address of the platform_device structure
 639  *
 640  * This function changes the driver state to "ready"
 641  *
 642  * Return:      0 on success and error value on error
 643  */
 644 static int __maybe_unused cdns_spi_resume(struct device *dev)
 645 {
 646         struct spi_master *master = dev_get_drvdata(dev);
 647         struct cdns_spi *xspi = spi_master_get_devdata(master);
 648
 649         cdns_spi_init_hw(xspi);
 650         return spi_master_resume(master);
 651 }
 652
 653 /**
 654  * cdns_spi_runtime_resume - Runtime resume method for the SPI driver
 655  * @dev:        Address of the platform_device structure
 656  *
 657  * This function enables the clocks
 658  *
 659  * Return:      0 on success and error value on error
 660  */
 661 static int __maybe_unused cdns_spi_runtime_resume(struct device *dev)
 662 {
 663         struct spi_master *master = dev_get_drvdata(dev);
 664         struct cdns_spi *xspi = spi_master_get_devdata(master);
 665         int ret;
 666
 667         ret = clk_prepare_enable(xspi->pclk);
 668         if (ret) {
 669                 dev_err(dev, "Cannot enable APB clock.\n");
 670                 return ret;
 671         }
 672
 673         ret = clk_prepare_enable(xspi->ref_clk);
 674         if (ret) {
 675                 dev_err(dev, "Cannot enable device clock.\n");
 676                 clk_disable_unprepare(xspi->pclk);
 677                 return ret;
 678         }
 679         return 0;
 680 }
 681
 682 /**
 683  * cdns_spi_runtime_suspend - Runtime suspend method for the SPI driver
 684  * @dev:        Address of the platform_device structure
 685  *
 686  * This function disables the clocks
 687  *
 688  * Return:      Always 0
 689  */
 690 static int __maybe_unused cdns_spi_runtime_suspend(struct device *dev)
 691 {
 692         struct spi_master *master = dev_get_drvdata(dev);
 693         struct cdns_spi *xspi = spi_master_get_devdata(master);
 694
 695         clk_disable_unprepare(xspi->ref_clk);
 696         clk_disable_unprepare(xspi->pclk);
 697
 698         return 0;
 699 }
 700
 701 static const struct dev_pm_ops cdns_spi_dev_pm_ops = {
 702         SET_RUNTIME_PM_OPS(cdns_spi_runtime_suspend,
 703                            cdns_spi_runtime_resume, NULL)
 704         SET_SYSTEM_SLEEP_PM_OPS(cdns_spi_suspend, cdns_spi_resume)
 705 };
 706
 707 static const struct of_device_id cdns_spi_of_match[] = {
 708         { .compatible = "xlnx,zynq-spi-r1p6" },
 709         { .compatible = "cdns,spi-r1p6" },
 710         { /* end of table */ }
 711 };
 712 MODULE_DEVICE_TABLE(of, cdns_spi_of_match);
 713
 714 /* cdns_spi_driver - This structure defines the SPI subsystem platform driver */
 715 static struct platform_driver cdns_spi_driver = {
 716         .probe  = cdns_spi_probe,
 717         .remove = cdns_spi_remove,
 718         .driver = {
 719                 .name = CDNS_SPI_NAME,
 720                 .of_match_table = cdns_spi_of_match,
 721                 .pm = &cdns_spi_dev_pm_ops,
 722         },
 723 };
 724
 725 module_platform_driver(cdns_spi_driver);
 726
 727 MODULE_AUTHOR("Xilinx, Inc.");
 728 MODULE_DESCRIPTION("Cadence SPI driver");
 729 MODULE_LICENSE("GPL");