1 # SPDX-License-Identifier: GPL-2.0-only
3 # Touchscreen driver configuration
5 menuconfig INPUT_TOUCHSCREEN
8 Say Y here, and a list of supported touchscreens will be displayed.
9 This option doesn't affect the kernel.
15 config TOUCHSCREEN_PROPERTIES
19 config TOUCHSCREEN_88PM860X
20 tristate "Marvell 88PM860x touchscreen"
21 depends on MFD_88PM860X
23 Say Y here if you have a 88PM860x PMIC and want to enable
24 support for the built-in touchscreen.
28 To compile this driver as a module, choose M here: the
29 module will be called 88pm860x-ts.
31 config TOUCHSCREEN_ADS7846
32 tristate "ADS7846/TSC2046/AD7873 and AD(S)7843 based touchscreens"
34 depends on HWMON = n || HWMON
36 Say Y here if you have a touchscreen interface using the
37 ADS7846/TSC2046/AD7873 or ADS7843/AD7843 controller,
38 and your board-specific setup code includes that in its
41 If HWMON is selected, and the driver is told the reference voltage
42 on your board, you will also get hwmon interfaces for the voltage
43 (and on ads7846/tsc2046/ad7873, temperature) sensors of this chip.
45 If unsure, say N (but it's safe to say "Y").
47 To compile this driver as a module, choose M here: the
48 module will be called ads7846.
50 config TOUCHSCREEN_AD7877
51 tristate "AD7877 based touchscreens"
54 Say Y here if you have a touchscreen interface using the
55 AD7877 controller, and your board-specific initialization
56 code includes that in its table of SPI devices.
58 If unsure, say N (but it's safe to say "Y").
60 To compile this driver as a module, choose M here: the
61 module will be called ad7877.
63 config TOUCHSCREEN_AD7879
64 tristate "Analog Devices AD7879-1/AD7889-1 touchscreen interface"
66 Say Y here if you want to support a touchscreen interface using
67 the AD7879-1/AD7889-1 controller.
69 You should select a bus connection too.
71 To compile this driver as a module, choose M here: the
72 module will be called ad7879.
74 config TOUCHSCREEN_AD7879_I2C
75 tristate "support I2C bus connection"
76 depends on TOUCHSCREEN_AD7879 && I2C
79 Say Y here if you have AD7879-1/AD7889-1 hooked to an I2C bus.
81 To compile this driver as a module, choose M here: the
82 module will be called ad7879-i2c.
84 config TOUCHSCREEN_AD7879_SPI
85 tristate "support SPI bus connection"
86 depends on TOUCHSCREEN_AD7879 && SPI_MASTER
89 Say Y here if you have AD7879-1/AD7889-1 hooked to a SPI bus.
91 If unsure, say N (but it's safe to say "Y").
93 To compile this driver as a module, choose M here: the
94 module will be called ad7879-spi.
96 config TOUCHSCREEN_ADC
97 tristate "Generic ADC based resistive touchscreen"
101 Say Y here if you want to use the generic ADC
102 resistive touchscreen driver.
104 If unsure, say N (but it's safe to say "Y").
106 To compile this driver as a module, choose M here: the
107 module will be called resistive-adc-touch.ko.
109 config TOUCHSCREEN_AR1021_I2C
110 tristate "Microchip AR1020/1021 i2c touchscreen"
113 Say Y here if you have the Microchip AR1020 or AR1021 touchscreen
114 controller chip in your system.
118 To compile this driver as a module, choose M here: the
119 module will be called ar1021_i2c.
121 config TOUCHSCREEN_ATMEL_MXT
122 tristate "Atmel mXT I2C Touchscreen"
126 Say Y here if you have Atmel mXT series I2C touchscreen,
127 such as AT42QT602240/ATMXT224, connected to your system.
131 To compile this driver as a module, choose M here: the
132 module will be called atmel_mxt_ts.
134 config TOUCHSCREEN_ATMEL_MXT_T37
135 bool "Support T37 Diagnostic Data"
136 depends on TOUCHSCREEN_ATMEL_MXT
137 depends on VIDEO_V4L2=y || (TOUCHSCREEN_ATMEL_MXT=m && VIDEO_V4L2=m)
138 select VIDEOBUF2_VMALLOC
140 Say Y here if you want support to output data from the T37
141 Diagnostic Data object using a V4L device.
143 config TOUCHSCREEN_AUO_PIXCIR
144 tristate "AUO in-cell touchscreen using Pixcir ICs"
146 depends on GPIOLIB || COMPILE_TEST
148 Say Y here if you have a AUO display with in-cell touchscreen
153 To compile this driver as a module, choose M here: the
154 module will be called auo-pixcir-ts.
156 config TOUCHSCREEN_BU21013
157 tristate "BU21013 based touch panel controllers"
160 Say Y here if you have a bu21013 touchscreen connected to
165 To compile this driver as a module, choose M here: the
166 module will be called bu21013_ts.
168 config TOUCHSCREEN_BU21029
169 tristate "Rohm BU21029 based touch panel controllers"
172 Say Y here if you have a Rohm BU21029 touchscreen controller
173 connected to your system.
177 To compile this driver as a module, choose M here: the
178 module will be called bu21029_ts.
180 config TOUCHSCREEN_CHIPONE_ICN8318
181 tristate "chipone icn8318 touchscreen controller"
182 depends on GPIOLIB || COMPILE_TEST
186 Say Y here if you have a ChipOne icn8318 based I2C touchscreen.
190 To compile this driver as a module, choose M here: the
191 module will be called chipone_icn8318.
193 config TOUCHSCREEN_CHIPONE_ICN8505
194 tristate "chipone icn8505 touchscreen controller"
195 depends on I2C && ACPI
197 Say Y here if you have a ChipOne icn8505 based I2C touchscreen.
201 To compile this driver as a module, choose M here: the
202 module will be called chipone_icn8505.
204 config TOUCHSCREEN_CY8CTMA140
205 tristate "cy8ctma140 touchscreen"
208 Say Y here if you have a Cypress CY8CTMA140 capacitive
209 touchscreen also just known as "TMA140"
213 To compile this driver as a module, choose M here: the
214 module will be called cy8ctma140.
216 config TOUCHSCREEN_CY8CTMG110
217 tristate "cy8ctmg110 touchscreen"
219 depends on GPIOLIB || COMPILE_TEST
221 Say Y here if you have a cy8ctmg110 capacitive touchscreen on
226 To compile this driver as a module, choose M here: the
227 module will be called cy8ctmg110_ts.
229 config TOUCHSCREEN_CYTTSP_CORE
230 tristate "Cypress TTSP touchscreen"
232 Say Y here if you have a touchscreen using controller from
233 the Cypress TrueTouch(tm) Standard Product family connected
234 to your system. You will also need to select appropriate
235 bus connection below.
239 To compile this driver as a module, choose M here: the
240 module will be called cyttsp_core.
242 config TOUCHSCREEN_CYTTSP_I2C
243 tristate "support I2C bus connection"
244 depends on TOUCHSCREEN_CYTTSP_CORE && I2C
246 Say Y here if the touchscreen is connected via I2C bus.
248 To compile this driver as a module, choose M here: the
249 module will be called cyttsp_i2c.
251 config TOUCHSCREEN_CYTTSP_SPI
252 tristate "support SPI bus connection"
253 depends on TOUCHSCREEN_CYTTSP_CORE && SPI_MASTER
255 Say Y here if the touchscreen is connected via SPI bus.
257 To compile this driver as a module, choose M here: the
258 module will be called cyttsp_spi.
260 config TOUCHSCREEN_CYTTSP4_CORE
261 tristate "Cypress TrueTouch Gen4 Touchscreen Driver"
263 Core driver for Cypress TrueTouch(tm) Standard Product
264 Generation4 touchscreen controllers.
266 Say Y here if you have a Cypress Gen4 touchscreen.
270 To compile this driver as a module, choose M here.
272 config TOUCHSCREEN_CYTTSP4_I2C
273 tristate "support I2C bus connection"
274 depends on TOUCHSCREEN_CYTTSP4_CORE && I2C
276 Say Y here if the touchscreen is connected via I2C bus.
278 To compile this driver as a module, choose M here: the
279 module will be called cyttsp4_i2c.
281 config TOUCHSCREEN_CYTTSP4_SPI
282 tristate "support SPI bus connection"
283 depends on TOUCHSCREEN_CYTTSP4_CORE && SPI_MASTER
285 Say Y here if the touchscreen is connected via SPI bus.
287 To compile this driver as a module, choose M here: the
288 module will be called cyttsp4_spi.
290 config TOUCHSCREEN_DA9034
291 tristate "Touchscreen support for Dialog Semiconductor DA9034"
292 depends on PMIC_DA903X
295 Say Y here to enable the support for the touchscreen found
296 on Dialog Semiconductor DA9034 PMIC.
300 To compile this driver as a module, choose M here: the
301 module will be called da9034-ts.
303 config TOUCHSCREEN_DA9052
304 tristate "Dialog DA9052/DA9053 TSI"
305 depends on PMIC_DA9052
307 Say Y here to support the touchscreen found on Dialog Semiconductor
308 DA9052-BC and DA9053-AA/Bx PMICs.
312 To compile this driver as a module, choose M here: the
313 module will be called da9052_tsi.
315 config TOUCHSCREEN_DYNAPRO
316 tristate "Dynapro serial touchscreen"
319 Say Y here if you have a Dynapro serial touchscreen connected to
324 To compile this driver as a module, choose M here: the
325 module will be called dynapro.
327 config TOUCHSCREEN_HAMPSHIRE
328 tristate "Hampshire serial touchscreen"
331 Say Y here if you have a Hampshire serial touchscreen connected to
336 To compile this driver as a module, choose M here: the
337 module will be called hampshire.
339 config TOUCHSCREEN_EETI
340 tristate "EETI touchscreen panel support"
343 Say Y here to enable support for I2C connected EETI touch panels.
345 To compile this driver as a module, choose M here: the
346 module will be called eeti_ts.
348 config TOUCHSCREEN_EGALAX
349 tristate "EETI eGalax multi-touch panel support"
352 Say Y here to enable support for I2C connected EETI
353 eGalax multi-touch panels.
355 To compile this driver as a module, choose M here: the
356 module will be called egalax_ts.
358 config TOUCHSCREEN_EGALAX_SERIAL
359 tristate "EETI eGalax serial touchscreen"
362 Say Y here to enable support for serial connected EETI
365 To compile this driver as a module, choose M here: the
366 module will be called egalax_ts_serial.
368 config TOUCHSCREEN_EXC3000
369 tristate "EETI EXC3000 multi-touch panel support"
372 Say Y here to enable support for I2C connected EETI
373 EXC3000 multi-touch panels.
375 To compile this driver as a module, choose M here: the
376 module will be called exc3000.
378 config TOUCHSCREEN_FUJITSU
379 tristate "Fujitsu serial touchscreen"
382 Say Y here if you have the Fujitsu touchscreen (such as one
383 installed in Lifebook P series laptop) connected to your
388 To compile this driver as a module, choose M here: the
389 module will be called fujitsu-ts.
391 config TOUCHSCREEN_GOODIX
392 tristate "Goodix I2C touchscreen"
394 depends on GPIOLIB || COMPILE_TEST
396 Say Y here if you have the Goodix touchscreen (such as one
397 installed in Onda v975w tablets) connected to your
398 system. It also supports 5-finger chip models, which can be
399 found on ARM tablets, like Wexler TAB7200 and MSI Primo73.
403 To compile this driver as a module, choose M here: the
404 module will be called goodix.
406 config TOUCHSCREEN_HIDEEP
407 tristate "HiDeep Touch IC"
410 Say Y here if you have a touchscreen using HiDeep.
414 To compile this driver as a module, choose M here : the
415 module will be called hideep_ts.
417 config TOUCHSCREEN_ILI210X
418 tristate "Ilitek ILI210X based touchscreen"
421 Say Y here if you have a ILI210X based touchscreen
422 controller. This driver supports models ILI2102,
423 ILI2102s, ILI2103, ILI2103s and ILI2105.
424 Such kind of chipsets can be found in Amazon Kindle Fire
429 To compile this driver as a module, choose M here: the
430 module will be called ili210x.
432 config TOUCHSCREEN_IPROC
433 tristate "IPROC touch panel driver support"
434 depends on ARCH_BCM_IPROC || COMPILE_TEST
436 Say Y here if you want to add support for the IPROC touch
437 controller to your system.
441 To compile this driver as a module, choose M here: the
442 module will be called bcm_iproc_tsc.
444 config TOUCHSCREEN_S3C2410
445 tristate "Samsung S3C2410/generic touchscreen input driver"
446 depends on ARCH_S3C24XX || SAMSUNG_DEV_TS
449 Say Y here if you have the s3c2410 touchscreen.
453 To compile this driver as a module, choose M here: the
454 module will be called s3c2410_ts.
456 config TOUCHSCREEN_S6SY761
457 tristate "Samsung S6SY761 Touchscreen driver"
460 Say Y if you have the Samsung S6SY761 driver
464 To compile this driver as module, choose M here: the
465 module will be called s6sy761.
467 config TOUCHSCREEN_GUNZE
468 tristate "Gunze AHL-51S touchscreen"
471 Say Y here if you have the Gunze AHL-51 touchscreen connected to
476 To compile this driver as a module, choose M here: the
477 module will be called gunze.
479 config TOUCHSCREEN_EKTF2127
480 tristate "Elan eKTF2127 I2C touchscreen"
483 Say Y here if you have an Elan eKTF2127 touchscreen
484 connected to your system.
488 To compile this driver as a module, choose M here: the
489 module will be called ektf2127.
491 config TOUCHSCREEN_ELAN
492 tristate "Elan eKTH I2C touchscreen"
495 Say Y here if you have an Elan eKTH I2C touchscreen
496 connected to your system.
500 To compile this driver as a module, choose M here: the
501 module will be called elants_i2c.
503 config TOUCHSCREEN_ELO
504 tristate "Elo serial touchscreens"
507 Say Y here if you have an Elo serial touchscreen connected to
512 To compile this driver as a module, choose M here: the
513 module will be called elo.
515 config TOUCHSCREEN_WACOM_W8001
516 tristate "Wacom W8001 penabled serial touchscreen"
519 Say Y here if you have an Wacom W8001 penabled serial touchscreen
520 connected to your system.
524 To compile this driver as a module, choose M here: the
525 module will be called wacom_w8001.
527 config TOUCHSCREEN_WACOM_I2C
528 tristate "Wacom Tablet support (I2C)"
531 Say Y here if you want to use the I2C version of the Wacom
536 To compile this driver as a module, choose M here: the module
537 will be called wacom_i2c.
539 config TOUCHSCREEN_LPC32XX
540 tristate "LPC32XX touchscreen controller"
541 depends on ARCH_LPC32XX
543 Say Y here if you have a LPC32XX device and want
544 to support the built-in touchscreen.
546 To compile this driver as a module, choose M here: the
547 module will be called lpc32xx_ts.
549 config TOUCHSCREEN_MAX11801
550 tristate "MAX11801 based touchscreens"
553 Say Y here if you have a MAX11801 based touchscreen
558 To compile this driver as a module, choose M here: the
559 module will be called max11801_ts.
561 config TOUCHSCREEN_MCS5000
562 tristate "MELFAS MCS-5000 touchscreen"
565 Say Y here if you have the MELFAS MCS-5000 touchscreen controller
570 To compile this driver as a module, choose M here: the
571 module will be called mcs5000_ts.
573 config TOUCHSCREEN_MMS114
574 tristate "MELFAS MMS114 touchscreen"
577 Say Y here if you have the MELFAS MMS114 touchscreen controller
582 To compile this driver as a module, choose M here: the
583 module will be called mms114.
585 config TOUCHSCREEN_MELFAS_MIP4
586 tristate "MELFAS MIP4 Touchscreen"
589 Say Y here if you have a MELFAS MIP4 Touchscreen device.
593 To compile this driver as a module, choose M here:
594 the module will be called melfas_mip4.
596 config TOUCHSCREEN_MTOUCH
597 tristate "MicroTouch serial touchscreens"
600 Say Y here if you have a MicroTouch (3M) serial touchscreen connected to
605 To compile this driver as a module, choose M here: the
606 module will be called mtouch.
608 config TOUCHSCREEN_IMX6UL_TSC
609 tristate "Freescale i.MX6UL touchscreen controller"
610 depends on (OF && GPIOLIB) || COMPILE_TEST
612 Say Y here if you have a Freescale i.MX6UL, and want to
613 use the internal touchscreen controller.
617 To compile this driver as a module, choose M here: the
618 module will be called imx6ul_tsc.
620 config TOUCHSCREEN_INEXIO
621 tristate "iNexio serial touchscreens"
624 Say Y here if you have an iNexio serial touchscreen connected to
629 To compile this driver as a module, choose M here: the
630 module will be called inexio.
632 config TOUCHSCREEN_MK712
633 tristate "ICS MicroClock MK712 touchscreen"
635 Say Y here if you have the ICS MicroClock MK712 touchscreen
636 controller chip in your system.
640 To compile this driver as a module, choose M here: the
641 module will be called mk712.
643 config TOUCHSCREEN_HP600
644 tristate "HP Jornada 6xx touchscreen"
645 depends on SH_HP6XX && SH_ADC
647 Say Y here if you have a HP Jornada 620/660/680/690 and want to
648 support the built-in touchscreen.
650 To compile this driver as a module, choose M here: the
651 module will be called hp680_ts_input.
653 config TOUCHSCREEN_HP7XX
654 tristate "HP Jornada 7xx touchscreen"
655 depends on SA1100_JORNADA720_SSP
657 Say Y here if you have a HP Jornada 710/720/728 and want
658 to support the built-in touchscreen.
660 To compile this driver as a module, choose M here: the
661 module will be called jornada720_ts.
663 config TOUCHSCREEN_IPAQ_MICRO
664 tristate "HP iPAQ Atmel Micro ASIC touchscreen"
665 depends on MFD_IPAQ_MICRO
667 Say Y here to enable support for the touchscreen attached to
668 the Atmel Micro peripheral controller on iPAQ h3100/h3600/h3700
672 To compile this driver as a module, choose M here: the
673 module will be called ipaq-micro-ts.
675 config TOUCHSCREEN_HTCPEN
676 tristate "HTC Shift X9500 touchscreen"
679 Say Y here if you have an HTC Shift UMPC also known as HTC X9500
680 Clio / Shangrila and want to support the built-in touchscreen.
684 To compile this driver as a module, choose M here: the
685 module will be called htcpen.
687 config TOUCHSCREEN_PENMOUNT
688 tristate "Penmount serial touchscreen"
691 Say Y here if you have a Penmount serial touchscreen connected to
696 To compile this driver as a module, choose M here: the
697 module will be called penmount.
699 config TOUCHSCREEN_EDT_FT5X06
700 tristate "EDT FocalTech FT5x06 I2C Touchscreen support"
703 Say Y here if you have an EDT "Polytouch" touchscreen based
704 on the FocalTech FT5x06 family of controllers connected to
709 To compile this driver as a module, choose M here: the
710 module will be called edt-ft5x06.
712 config TOUCHSCREEN_RASPBERRYPI_FW
713 tristate "Raspberry Pi's firmware base touch screen support"
714 depends on RASPBERRYPI_FIRMWARE || (RASPBERRYPI_FIRMWARE=n && COMPILE_TEST)
716 Say Y here if you have the official Raspberry Pi 7 inch screen on
721 To compile this driver as a module, choose M here: the
722 module will be called raspberrypi-ts.
724 config TOUCHSCREEN_MIGOR
725 tristate "Renesas MIGO-R touchscreen"
726 depends on (SH_MIGOR || COMPILE_TEST) && I2C
728 Say Y here to enable MIGO-R touchscreen support.
732 To compile this driver as a module, choose M here: the
733 module will be called migor_ts.
735 config TOUCHSCREEN_TOUCHRIGHT
736 tristate "Touchright serial touchscreen"
739 Say Y here if you have a Touchright serial touchscreen connected to
744 To compile this driver as a module, choose M here: the
745 module will be called touchright.
747 config TOUCHSCREEN_TOUCHWIN
748 tristate "Touchwin serial touchscreen"
751 Say Y here if you have a Touchwin serial touchscreen connected to
756 To compile this driver as a module, choose M here: the
757 module will be called touchwin.
759 config TOUCHSCREEN_TI_AM335X_TSC
760 tristate "TI Touchscreen Interface"
761 depends on MFD_TI_AM335X_TSCADC
763 Say Y here if you have 4/5/8 wire touchscreen controller
764 to be connected to the ADC controller on your TI AM335x SoC.
768 To compile this driver as a module, choose M here: the
769 module will be called ti_am335x_tsc.
771 config TOUCHSCREEN_UCB1400
772 tristate "Philips UCB1400 touchscreen"
774 depends on UCB1400_CORE
776 This enables support for the Philips UCB1400 touchscreen interface.
777 The UCB1400 is an AC97 audio codec. The touchscreen interface
778 will be initialized only after the ALSA subsystem has been
779 brought up and the UCB1400 detected. You therefore have to
780 configure ALSA support as well (either built-in or modular,
781 independently of whether this driver is itself built-in or
782 modular) for this driver to work.
784 To compile this driver as a module, choose M here: the
785 module will be called ucb1400_ts.
787 config TOUCHSCREEN_PIXCIR
788 tristate "PIXCIR I2C touchscreens"
791 Say Y here if you have a pixcir i2c touchscreen
796 To compile this driver as a module, choose M here: the
797 module will be called pixcir_i2c_ts.
799 config TOUCHSCREEN_WDT87XX_I2C
800 tristate "Weida HiTech I2C touchscreen"
803 Say Y here if you have a Weida WDT87XX I2C touchscreen
804 connected to your system.
808 To compile this driver as a module, choose M here: the
809 module will be called wdt87xx_i2c.
811 config TOUCHSCREEN_WM831X
812 tristate "Support for WM831x touchscreen controllers"
813 depends on MFD_WM831X
815 This enables support for the touchscreen controller on the WM831x
818 To compile this driver as a module, choose M here: the
819 module will be called wm831x-ts.
821 config TOUCHSCREEN_WM97XX
822 tristate "Support for WM97xx AC97 touchscreen controllers"
823 depends on AC97_BUS || AC97_BUS_NEW
825 Say Y here if you have a Wolfson Microelectronics WM97xx
826 touchscreen connected to your system. Note that this option
827 only enables core driver, you will also need to select
828 support for appropriate chip below.
832 To compile this driver as a module, choose M here: the
833 module will be called wm97xx-ts.
835 config TOUCHSCREEN_WM9705
836 bool "WM9705 Touchscreen interface support"
837 depends on TOUCHSCREEN_WM97XX
840 Say Y here to enable support for the Wolfson Microelectronics
841 WM9705 touchscreen controller.
843 config TOUCHSCREEN_WM9712
844 bool "WM9712 Touchscreen interface support"
845 depends on TOUCHSCREEN_WM97XX
848 Say Y here to enable support for the Wolfson Microelectronics
849 WM9712 touchscreen controller.
851 config TOUCHSCREEN_WM9713
852 bool "WM9713 Touchscreen interface support"
853 depends on TOUCHSCREEN_WM97XX
856 Say Y here to enable support for the Wolfson Microelectronics
857 WM9713 touchscreen controller.
859 config TOUCHSCREEN_WM97XX_MAINSTONE
860 tristate "WM97xx Mainstone/Palm accelerated touch"
861 depends on TOUCHSCREEN_WM97XX && ARCH_PXA
863 Say Y here for support for streaming mode with WM97xx touchscreens
864 on Mainstone, Palm Tungsten T5, TX and LifeDrive systems.
868 To compile this driver as a module, choose M here: the
869 module will be called mainstone-wm97xx.
871 config TOUCHSCREEN_WM97XX_ZYLONITE
872 tristate "Zylonite accelerated touch"
873 depends on TOUCHSCREEN_WM97XX && MACH_ZYLONITE
874 select TOUCHSCREEN_WM9713
876 Say Y here for support for streaming mode with the touchscreen
881 To compile this driver as a module, choose M here: the
882 module will be called zylonite-wm97xx.
884 config TOUCHSCREEN_USB_COMPOSITE
885 tristate "USB Touchscreen Driver"
886 depends on USB_ARCH_HAS_HCD
889 USB Touchscreen driver for:
890 - eGalax Touchkit USB (also includes eTurboTouch CT-410/510/700)
891 - PanJit TouchSet USB
892 - 3M MicroTouch USB (EX II series)
894 - some other eTurboTouch
897 - IRTOUCHSYSTEMS/UNITOP
899 - GoTop Super_Q2/GogoPen/PenPower tablets
900 - JASTEC USB Touch Controller/DigiTech DTR-02U
901 - Zytronic controllers
902 - Elo TouchSystems 2700 IntelliTouch
903 - EasyTouch USB Touch Controller from Data Modul
904 - e2i (Mimo monitors)
906 Have a look at <http://linux.chapter7.ch/touchkit/> for
907 a usage description and the required user-space stuff.
909 To compile this driver as a module, choose M here: the
910 module will be called usbtouchscreen.
912 config TOUCHSCREEN_MXS_LRADC
913 tristate "Freescale i.MX23/i.MX28 LRADC touchscreen"
914 depends on MFD_MXS_LRADC
916 Say Y here if you have a touchscreen connected to the low-resolution
917 analog-to-digital converter (LRADC) on an i.MX23 or i.MX28 processor.
919 To compile this driver as a module, choose M here: the module will be
922 config TOUCHSCREEN_MX25
923 tristate "Freescale i.MX25 touchscreen input driver"
924 depends on MFD_MX25_TSADC
926 Enable support for touchscreen connected to your i.MX25.
928 To compile this driver as a module, choose M here: the
929 module will be called fsl-imx25-tcq.
931 config TOUCHSCREEN_MC13783
932 tristate "Freescale MC13783 touchscreen input driver"
933 depends on MFD_MC13XXX
935 Say Y here if you have an Freescale MC13783 PMIC on your
936 board and want to use its touchscreen
940 To compile this driver as a module, choose M here: the
941 module will be called mc13783_ts.
943 config TOUCHSCREEN_USB_EGALAX
945 bool "eGalax, eTurboTouch CT-410/510/700 device support" if EXPERT
946 depends on TOUCHSCREEN_USB_COMPOSITE
948 config TOUCHSCREEN_USB_PANJIT
950 bool "PanJit device support" if EXPERT
951 depends on TOUCHSCREEN_USB_COMPOSITE
953 config TOUCHSCREEN_USB_3M
955 bool "3M/Microtouch EX II series device support" if EXPERT
956 depends on TOUCHSCREEN_USB_COMPOSITE
958 config TOUCHSCREEN_USB_ITM
960 bool "ITM device support" if EXPERT
961 depends on TOUCHSCREEN_USB_COMPOSITE
963 config TOUCHSCREEN_USB_ETURBO
965 bool "eTurboTouch (non-eGalax compatible) device support" if EXPERT
966 depends on TOUCHSCREEN_USB_COMPOSITE
968 config TOUCHSCREEN_USB_GUNZE
970 bool "Gunze AHL61 device support" if EXPERT
971 depends on TOUCHSCREEN_USB_COMPOSITE
973 config TOUCHSCREEN_USB_DMC_TSC10
975 bool "DMC TSC-10/25 device support" if EXPERT
976 depends on TOUCHSCREEN_USB_COMPOSITE
978 config TOUCHSCREEN_USB_IRTOUCH
980 bool "IRTOUCHSYSTEMS/UNITOP device support" if EXPERT
981 depends on TOUCHSCREEN_USB_COMPOSITE
983 config TOUCHSCREEN_USB_IDEALTEK
985 bool "IdealTEK URTC1000 device support" if EXPERT
986 depends on TOUCHSCREEN_USB_COMPOSITE
988 config TOUCHSCREEN_USB_GENERAL_TOUCH
990 bool "GeneralTouch Touchscreen device support" if EXPERT
991 depends on TOUCHSCREEN_USB_COMPOSITE
993 config TOUCHSCREEN_USB_GOTOP
995 bool "GoTop Super_Q2/GogoPen/PenPower tablet device support" if EXPERT
996 depends on TOUCHSCREEN_USB_COMPOSITE
998 config TOUCHSCREEN_USB_JASTEC
1000 bool "JASTEC/DigiTech DTR-02U USB touch controller device support" if EXPERT
1001 depends on TOUCHSCREEN_USB_COMPOSITE
1003 config TOUCHSCREEN_USB_ELO
1005 bool "Elo TouchSystems 2700 IntelliTouch controller device support" if EXPERT
1006 depends on TOUCHSCREEN_USB_COMPOSITE
1008 config TOUCHSCREEN_USB_E2I
1010 bool "e2i Touchscreen controller (e.g. from Mimo 740)" if EXPERT
1011 depends on TOUCHSCREEN_USB_COMPOSITE
1013 config TOUCHSCREEN_USB_ZYTRONIC
1015 bool "Zytronic controller" if EXPERT
1016 depends on TOUCHSCREEN_USB_COMPOSITE
1018 config TOUCHSCREEN_USB_ETT_TC45USB
1020 bool "ET&T USB series TC4UM/TC5UH touchscreen controller support" if EXPERT
1021 depends on TOUCHSCREEN_USB_COMPOSITE
1023 config TOUCHSCREEN_USB_NEXIO
1025 bool "NEXIO/iNexio device support" if EXPERT
1026 depends on TOUCHSCREEN_USB_COMPOSITE
1028 config TOUCHSCREEN_USB_EASYTOUCH
1030 bool "EasyTouch USB Touch controller device support" if EXPERT
1031 depends on TOUCHSCREEN_USB_COMPOSITE
1033 Say Y here if you have an EasyTouch USB Touch controller.
1036 config TOUCHSCREEN_TOUCHIT213
1037 tristate "Sahara TouchIT-213 touchscreen"
1040 Say Y here if you have a Sahara TouchIT-213 Tablet PC.
1044 To compile this driver as a module, choose M here: the
1045 module will be called touchit213.
1047 config TOUCHSCREEN_TS4800
1048 tristate "TS-4800 touchscreen"
1049 depends on HAS_IOMEM && OF
1050 depends on SOC_IMX51 || COMPILE_TEST
1053 Say Y here if you have a touchscreen on a TS-4800 board.
1055 On TS-4800, the touchscreen is not handled directly by Linux but by
1060 To compile this driver as a module, choose M here: the
1061 module will be called ts4800_ts.
1063 config TOUCHSCREEN_TSC_SERIO
1064 tristate "TSC-10/25/40 serial touchscreen support"
1067 Say Y here if you have a TSC-10, 25 or 40 serial touchscreen connected
1072 To compile this driver as a module, choose M here: the
1073 module will be called tsc40.
1075 config TOUCHSCREEN_TSC200X_CORE
1078 config TOUCHSCREEN_TSC2004
1079 tristate "TSC2004 based touchscreens"
1082 select TOUCHSCREEN_TSC200X_CORE
1084 Say Y here if you have a TSC2004 based touchscreen.
1088 To compile this driver as a module, choose M here: the
1089 module will be called tsc2004.
1091 config TOUCHSCREEN_TSC2005
1092 tristate "TSC2005 based touchscreens"
1093 depends on SPI_MASTER
1095 select TOUCHSCREEN_TSC200X_CORE
1097 Say Y here if you have a TSC2005 based touchscreen.
1101 To compile this driver as a module, choose M here: the
1102 module will be called tsc2005.
1104 config TOUCHSCREEN_TSC2007
1105 tristate "TSC2007 based touchscreens"
1108 Say Y here if you have a TSC2007 based touchscreen.
1112 To compile this driver as a module, choose M here: the
1113 module will be called tsc2007.
1115 config TOUCHSCREEN_TSC2007_IIO
1116 bool "IIO interface for external ADC input and temperature"
1117 depends on TOUCHSCREEN_TSC2007
1118 depends on IIO=y || IIO=TOUCHSCREEN_TSC2007
1120 Saying Y here adds an iio interface to the tsc2007 which
1121 provides values for the AUX input (used for e.g. battery
1122 or ambient light monitoring), temperature and raw input
1125 config TOUCHSCREEN_PCAP
1126 tristate "Motorola PCAP touchscreen"
1129 Say Y here if you have a Motorola EZX telephone and
1130 want to enable support for the built-in touchscreen.
1132 To compile this driver as a module, choose M here: the
1133 module will be called pcap_ts.
1135 config TOUCHSCREEN_RM_TS
1136 tristate "Raydium I2C Touchscreen"
1138 depends on GPIOLIB || COMPILE_TEST
1140 Say Y here if you have Raydium series I2C touchscreen,
1141 such as RM32380, connected to your system.
1145 To compile this driver as a module, choose M here: the
1146 module will be called raydium_i2c_ts.
1148 config TOUCHSCREEN_SILEAD
1149 tristate "Silead I2C touchscreen"
1152 Say Y here if you have the Silead touchscreen connected to
1157 To compile this driver as a module, choose M here: the
1158 module will be called silead.
1160 config TOUCHSCREEN_SIS_I2C
1161 tristate "SiS 9200 family I2C touchscreen"
1164 depends on GPIOLIB || COMPILE_TEST
1166 This enables support for SiS 9200 family over I2C based touchscreens.
1170 To compile this driver as a module, choose M here: the
1171 module will be called sis_i2c.
1173 config TOUCHSCREEN_ST1232
1174 tristate "Sitronix ST1232 or ST1633 touchscreen controllers"
1177 Say Y here if you want to support the Sitronix ST1232
1178 or ST1633 touchscreen controller.
1182 To compile this driver as a module, choose M here: the
1183 module will be called st1232_ts.
1185 config TOUCHSCREEN_STMFTS
1186 tristate "STMicroelectronics STMFTS touchscreen"
1188 depends on LEDS_CLASS
1190 Say Y here if you want support for STMicroelectronics
1193 To compile this driver as a module, choose M here: the
1194 module will be called stmfts.
1196 config TOUCHSCREEN_STMPE
1197 tristate "STMicroelectronics STMPE touchscreens"
1198 depends on MFD_STMPE
1199 depends on (OF || COMPILE_TEST)
1201 Say Y here if you want support for STMicroelectronics
1202 STMPE touchscreen controllers.
1204 To compile this driver as a module, choose M here: the
1205 module will be called stmpe-ts.
1207 config TOUCHSCREEN_SUN4I
1208 tristate "Allwinner sun4i resistive touchscreen controller support"
1209 depends on ARCH_SUNXI || COMPILE_TEST
1211 depends on THERMAL || !THERMAL_OF
1213 This selects support for the resistive touchscreen controller
1214 found on Allwinner sunxi SoCs.
1216 To compile this driver as a module, choose M here: the
1217 module will be called sun4i-ts.
1219 config TOUCHSCREEN_SUR40
1220 tristate "Samsung SUR40 (Surface 2.0/PixelSense) touchscreen"
1221 depends on USB && MEDIA_USB_SUPPORT && HAS_DMA
1222 depends on VIDEO_V4L2
1223 select VIDEOBUF2_DMA_SG
1225 Say Y here if you want support for the Samsung SUR40 touchscreen
1226 (also known as Microsoft Surface 2.0 or Microsoft PixelSense).
1228 To compile this driver as a module, choose M here: the
1229 module will be called sur40.
1231 config TOUCHSCREEN_SURFACE3_SPI
1232 tristate "Ntrig/Microsoft Surface 3 SPI touchscreen"
1234 depends on GPIOLIB || COMPILE_TEST
1236 Say Y here if you have the Ntrig/Microsoft SPI touchscreen
1237 controller chip as found on the Surface 3 in your system.
1241 To compile this driver as a module, choose M here: the
1242 module will be called surface3_spi.
1244 config TOUCHSCREEN_SX8654
1245 tristate "Semtech SX8654 touchscreen"
1248 Say Y here if you have a Semtech SX8654 touchscreen controller.
1252 To compile this driver as a module, choose M here: the
1253 module will be called sx8654.
1255 config TOUCHSCREEN_TPS6507X
1256 tristate "TPS6507x based touchscreens"
1259 Say Y here if you have a TPS6507x based touchscreen
1264 To compile this driver as a module, choose M here: the
1265 module will be called tps6507x_ts.
1267 config TOUCHSCREEN_ZET6223
1268 tristate "Zeitec ZET6223 touchscreen driver"
1271 Say Y here if you have a touchscreen using Zeitec ZET6223
1275 To compile this driver as a module, choose M here: the
1276 module will be called zet6223.
1278 config TOUCHSCREEN_ZFORCE
1279 tristate "Neonode zForce infrared touchscreens"
1281 depends on GPIOLIB || COMPILE_TEST
1283 Say Y here if you have a touchscreen using the zforce
1284 infraread technology from Neonode.
1288 To compile this driver as a module, choose M here: the
1289 module will be called zforce_ts.
1291 config TOUCHSCREEN_COLIBRI_VF50
1292 tristate "Toradex Colibri on board touchscreen driver"
1293 depends on IIO && VF610_ADC
1294 depends on GPIOLIB || COMPILE_TEST
1296 Say Y here if you have a Colibri VF50 and plan to use
1297 the on-board provided 4-wire touchscreen driver.
1301 To compile this driver as a module, choose M here: the
1302 module will be called colibri_vf50_ts.
1304 config TOUCHSCREEN_ROHM_BU21023
1305 tristate "ROHM BU21023/24 Dual touch support resistive touchscreens"
1308 Say Y here if you have a touchscreen using ROHM BU21023/24.
1312 To compile this driver as a module, choose M here: the
1313 module will be called bu21023_ts.
1315 config TOUCHSCREEN_IQS5XX
1316 tristate "Azoteq IQS550/572/525 trackpad/touchscreen controller"
1319 Say Y to enable support for the Azoteq IQS550/572/525
1320 family of trackpad/touchscreen controllers.
1322 To compile this driver as a module, choose M here: the
1323 module will be called iqs5xx.