1 // SPDX-License-Identifier: BSD-3-Clause
3 * Copyright (c) 2020, Konrad Dybcio <konrad.dybcio@somainline.org>
4 * Copyright (c) 2020, AngeloGioacchino Del Regno
5 * <angelogioacchino.delregno@somainline.org>
10 #include <dt-bindings/gpio/gpio.h>
11 #include <dt-bindings/input/input.h>
12 #include <dt-bindings/input/gpio-keys.h>
13 #include <dt-bindings/leds/common.h>
16 /* required for bootloader to select correct board */
17 qcom,msm-id = <318 0>;
18 qcom,board-id = <8 1>;
19 qcom,pmic-id = <0x1001b 0x101011a 0x00 0x00 0x1001b 0x201011a 0x00 0x00>;
21 /* This part enables graphical output via bootloader-enabled display */
23 bootargs = "earlycon=tty0 console=tty0";
29 stdout-path = "framebuffer0";
31 framebuffer0: framebuffer@9d400000 {
32 compatible = "simple-framebuffer";
33 reg = <0 0x9d400000 0 (1920 * 1080 * 4)>;
36 stride = <(1080 * 4)>;
42 board_vbat: vbat-regulator {
43 compatible = "regulator-fixed";
44 regulator-name = "VBAT";
46 regulator-min-microvolt = <4000000>;
47 regulator-max-microvolt = <4000000>;
52 vph_pwr: vph-pwr-regulator {
53 compatible = "regulator-fixed";
54 regulator-name = "vph_pwr";
60 cam_vdig_imx300_219_vreg: cam-vdig-imx300-219-regulator {
61 compatible = "regulator-fixed";
62 regulator-name = "cam_vdig_imx300_219_vreg";
63 startup-delay-us = <0>;
65 gpio = <&tlmm 52 GPIO_ACTIVE_HIGH>;
66 pinctrl-names = "default";
67 pinctrl-0 = <&cam_vdig_default>;
70 cam_vana_front_vreg: cam-vana-front-regulator {
71 compatible = "regulator-fixed";
72 regulator-name = "cam_vana_front_vreg";
73 startup-delay-us = <0>;
75 gpio = <&tlmm 51 GPIO_ACTIVE_HIGH>;
76 pinctrl-names = "default";
77 pinctrl-0 = <&imx219_vana_default>;
80 cam_vana_rear_vreg: cam-vana-rear-regulator {
81 compatible = "regulator-fixed";
82 regulator-name = "cam_vana_rear_vreg";
83 startup-delay-us = <0>;
85 gpio = <&tlmm 50 GPIO_ACTIVE_HIGH>;
87 pinctrl-names = "default";
88 pinctrl-0 = <&imx300_vana_default>;
92 compatible = "gpio-keys";
95 label = "Camera Focus";
96 gpios = <&tlmm 64 GPIO_ACTIVE_LOW>;
97 linux,input-type = <1>;
98 linux,code = <KEY_CAMERA_FOCUS>;
99 debounce-interval = <15>;
102 key-camera-snapshot {
103 label = "Camera Snapshot";
104 gpios = <&tlmm 113 GPIO_ACTIVE_LOW>;
105 linux,input-type = <1>;
106 linux,code = <KEY_CAMERA>;
107 debounce-interval = <15>;
111 label = "Volume Down";
112 gpios = <&pm660l_gpios 7 GPIO_ACTIVE_LOW>;
113 linux,input-type = <1>;
114 linux,code = <KEY_VOLUMEDOWN>;
116 debounce-interval = <15>;
121 #address-cells = <2>;
126 compatible = "ramoops";
127 reg = <0x0 0xffc00000 0x0 0x100000>;
128 record-size = <0x10000>;
129 console-size = <0x60000>;
130 ftrace-size = <0x10000>;
131 pmsg-size = <0x20000>;
137 reg = <0x00 0xffb00000 0x00 0x100000>;
141 cont_splash_mem: splash@9d400000 {
142 reg = <0 0x9d400000 0 (1920 * 1080 * 4)>;
148 * Until we hook up type-c detection, we
149 * have to stick with this. But it works.
151 extcon_usb: extcon-usb {
152 compatible = "linux,extcon-usb-gpio";
153 id-gpios = <&tlmm 58 GPIO_ACTIVE_HIGH>;
158 firmware-name = "qcom/sdm630/Sony/nile/adsp.mdt";
164 touchscreen: synaptics-rmi4-i2c@70 {
165 compatible = "syna,rmi4-i2c";
167 #address-cells = <1>;
169 interrupts-extended = <&tlmm 45 0x2008>;
171 pinctrl-names = "default";
172 pinctrl-0 = <&ts_int_active &ts_lcd_id_active>;
174 syna,reset-delay-ms = <200>;
175 syna,startup-delay-ms = <220>;
179 syna,nosleep-mode = <1>;
184 syna,sensor-type = <1>;
192 /* SMB1351 charger */
195 /* I2C3, 4, 5, 7 and 8 are disabled on this board. */
206 /* MSM serial console */
216 qcom,power-source = <1>;
221 color = <LED_COLOR_ID_RGB>;
222 function = LED_FUNCTION_STATUS;
224 #address-cells = <1>;
229 color = <LED_COLOR_ID_BLUE>;
234 color = <LED_COLOR_ID_GREEN>;
239 color = <LED_COLOR_ID_RED>;
247 qcom,switching-freq = <800>;
248 qcom,ovp-millivolt = <29600>;
249 qcom,current-boost-limit = <970>;
250 qcom,current-limit-microamp = <17500>;
251 qcom,num-strings = <2>;
261 linux,code = <KEY_VOLUMEUP>;
265 reg = <0x00 0x85800000 0x00 0x3700000>;
271 vdd-supply = <&vreg_l1b_0p925>;
272 vdda-pll-supply = <&vreg_l10a_1p8>;
273 vdda-phy-dpdm-supply = <&vreg_l7b_3p125>;
278 compatible = "qcom,rpm-pm660l-regulators";
280 vdd_s1-supply = <&vph_pwr>;
281 vdd_s2-supply = <&vph_pwr>;
282 vdd_s3_s4-supply = <&vph_pwr>;
283 vdd_s5-supply = <&vph_pwr>;
284 vdd_s6-supply = <&vph_pwr>;
286 vdd_l1_l9_l10-supply = <&vreg_s2b_1p05>;
287 vdd_l2-supply = <&vreg_bob>;
288 vdd_l3_l5_l7_l8-supply = <&vreg_bob>;
289 vdd_l4_l6-supply = <&vreg_bob>;
290 vdd_bob-supply = <&vph_pwr>;
293 regulator-min-microvolt = <1125000>;
294 regulator-max-microvolt = <1125000>;
295 regulator-enable-ramp-delay = <200>;
296 regulator-ramp-delay = <0>;
300 regulator-min-microvolt = <1050000>;
301 regulator-max-microvolt = <1050000>;
302 regulator-enable-ramp-delay = <200>;
303 regulator-ramp-delay = <0>;
307 * At least on Nile's configuration, S3B/S4B (VDD_CX) and
308 * S5B (VDD_MX) are managed only through RPM Power Domains.
309 * Trying to set a voltage on the main supply will create
310 * havoc and freeze the SoC.
311 * In any case, reference voltages for these regulators are:
318 regulator-min-microvolt = <920000>;
319 regulator-max-microvolt = <928000>;
320 regulator-enable-ramp-delay = <250>;
321 regulator-ramp-delay = <0>;
322 regulator-allow-set-load;
327 * This regulator supports 1.648 - 3.104V on this board
328 * but we set a max voltage of anything less than 2.7V
329 * to satisfy a condition in sdhci.c that will disable
330 * 3.3V SDHCI signaling, which happens to be not really
331 * supported on the Xperia Nile/Ganges platform.
333 regulator-min-microvolt = <1648000>;
334 regulator-max-microvolt = <2696000>;
335 regulator-enable-ramp-delay = <250>;
336 regulator-ramp-delay = <0>;
337 regulator-allow-set-load;
341 regulator-min-microvolt = <2800000>;
342 regulator-max-microvolt = <2800000>;
343 regulator-enable-ramp-delay = <250>;
344 regulator-ramp-delay = <0>;
345 regulator-min-microamp = <200>;
346 regulator-max-microamp = <600000>;
347 regulator-system-load = <100000>;
348 regulator-allow-set-load;
352 regulator-min-microvolt = <2944000>;
353 regulator-max-microvolt = <2952000>;
354 regulator-enable-ramp-delay = <250>;
355 regulator-ramp-delay = <0>;
357 regulator-min-microamp = <200>;
358 regulator-max-microamp = <600000>;
359 regulator-system-load = <570000>;
360 regulator-allow-set-load;
364 * Downstream specifies a range of 1721-3600mV,
365 * but the only assigned consumers are SDHCI2 VMMC
366 * and Coresight QPDI that both request pinned 2.95V.
367 * Tighten the range to 1.8-3.328 (closest to 3.3) to
368 * make the mmc driver happy.
371 regulator-min-microvolt = <1800000>;
372 regulator-max-microvolt = <3328000>;
373 regulator-enable-ramp-delay = <250>;
374 regulator-ramp-delay = <0>;
375 regulator-allow-set-load;
376 regulator-system-load = <800000>;
380 regulator-min-microvolt = <1704000>;
381 regulator-max-microvolt = <3312000>;
382 regulator-enable-ramp-delay = <250>;
383 regulator-ramp-delay = <0>;
387 regulator-min-microvolt = <2704000>;
388 regulator-max-microvolt = <3128000>;
389 regulator-enable-ramp-delay = <250>;
390 regulator-ramp-delay = <0>;
394 regulator-min-microvolt = <2800000>;
395 regulator-max-microvolt = <3400000>;
396 regulator-enable-ramp-delay = <250>;
397 regulator-ramp-delay = <0>;
400 /* L9B (870mV) is currently unused */
401 /* L10B (915mV) is currently unused */
404 regulator-min-microvolt = <3304000>;
405 regulator-max-microvolt = <3624000>;
406 regulator-enable-ramp-delay = <500>;
407 regulator-ramp-delay = <0>;
412 compatible = "qcom,rpm-pm660-regulators";
414 vdd_s1-supply = <&vph_pwr>;
415 vdd_s2-supply = <&vph_pwr>;
416 vdd_s3-supply = <&vph_pwr>;
417 vdd_s4-supply = <&vph_pwr>;
418 vdd_s5-supply = <&vph_pwr>;
419 vdd_s6-supply = <&vph_pwr>;
421 vdd_l1_l6_l7-supply = <&vreg_s5a_1p35>;
422 vdd_l2_l3-supply = <&vreg_s2b_1p05>;
423 vdd_l5-supply = <&vreg_s2b_1p05>;
424 vdd_l8_l9_l10_l11_l12_l13_l14-supply = <&vreg_s4a_2p04>;
425 vdd_l15_l16_l17_l18_l19-supply = <&vreg_bob>;
428 * S1A (FTAPC0), S2A (FTAPC1), S3A (HFAPC1) are managed
429 * by the Core Power Reduction hardened (CPRh) and the
430 * Operating State Manager (OSM) HW automatically.
434 regulator-min-microvolt = <2040000>;
435 regulator-max-microvolt = <2040000>;
436 regulator-enable-ramp-delay = <200>;
437 regulator-ramp-delay = <0>;
442 regulator-min-microvolt = <1224000>;
443 regulator-max-microvolt = <1350000>;
444 regulator-enable-ramp-delay = <200>;
445 regulator-ramp-delay = <0>;
449 regulator-min-microvolt = <504000>;
450 regulator-max-microvolt = <992000>;
451 regulator-enable-ramp-delay = <150>;
452 regulator-ramp-delay = <0>;
457 regulator-min-microvolt = <1226000>;
458 regulator-max-microvolt = <1250000>;
459 regulator-enable-ramp-delay = <250>;
460 regulator-ramp-delay = <0>;
461 regulator-allow-set-load;
465 regulator-min-microvolt = <944000>;
466 regulator-max-microvolt = <1008000>;
467 regulator-enable-ramp-delay = <250>;
468 regulator-ramp-delay = <0>;
472 regulator-min-microvolt = <944000>;
473 regulator-max-microvolt = <1008000>;
474 regulator-enable-ramp-delay = <250>;
475 regulator-ramp-delay = <0>;
479 regulator-min-microvolt = <800000>;
480 regulator-max-microvolt = <952000>;
481 regulator-enable-ramp-delay = <250>;
482 regulator-ramp-delay = <0>;
486 regulator-min-microvolt = <1304000>;
487 regulator-max-microvolt = <1368000>;
488 regulator-allow-set-load;
489 regulator-enable-ramp-delay = <250>;
490 regulator-ramp-delay = <0>;
494 regulator-min-microvolt = <1200000>;
495 regulator-max-microvolt = <1200000>;
496 regulator-enable-ramp-delay = <250>;
497 regulator-ramp-delay = <0>;
501 regulator-min-microvolt = <1800000>;
502 regulator-max-microvolt = <1800000>;
503 regulator-enable-ramp-delay = <250>;
504 regulator-ramp-delay = <0>;
505 regulator-system-load = <325000>;
506 regulator-allow-set-load;
510 regulator-min-microvolt = <1804000>;
511 regulator-max-microvolt = <1896000>;
512 regulator-enable-ramp-delay = <250>;
513 regulator-ramp-delay = <0>;
514 regulator-allow-set-load;
518 regulator-min-microvolt = <1800000>;
519 regulator-max-microvolt = <1944000>;
520 regulator-enable-ramp-delay = <250>;
521 regulator-ramp-delay = <0>;
522 regulator-allow-set-load;
526 regulator-min-microvolt = <1784000>;
527 regulator-max-microvolt = <1944000>;
528 regulator-enable-ramp-delay = <250>;
529 regulator-ramp-delay = <0>;
533 regulator-min-microvolt = <1800000>;
534 regulator-max-microvolt = <1944000>;
535 regulator-enable-ramp-delay = <250>;
536 regulator-ramp-delay = <0>;
539 /* This gives power to the LPDDR4: never turn it off! */
541 regulator-min-microvolt = <1800000>;
542 regulator-max-microvolt = <1944000>;
543 regulator-enable-ramp-delay = <250>;
544 regulator-ramp-delay = <0>;
550 regulator-min-microvolt = <1710000>;
551 regulator-max-microvolt = <1904000>;
552 regulator-enable-ramp-delay = <250>;
553 regulator-ramp-delay = <0>;
557 regulator-min-microvolt = <1648000>;
558 regulator-max-microvolt = <2952000>;
559 regulator-enable-ramp-delay = <250>;
560 regulator-ramp-delay = <0>;
563 /* L16A (2.70V) is unused */
566 regulator-min-microvolt = <1648000>;
567 regulator-max-microvolt = <2952000>;
568 regulator-enable-ramp-delay = <250>;
569 regulator-ramp-delay = <0>;
573 regulator-min-microvolt = <1800000>;
574 regulator-max-microvolt = <1800000>;
575 regulator-enable-ramp-delay = <250>;
576 regulator-ramp-delay = <10>;
577 regulator-min-microamp = <200>;
578 regulator-max-microamp = <50000>;
579 regulator-system-load = <10000>;
580 regulator-allow-set-load;
584 regulator-min-microvolt = <3312000>;
585 regulator-max-microvolt = <3400000>;
586 regulator-enable-ramp-delay = <250>;
587 regulator-ramp-delay = <0>;
588 regulator-allow-set-load;
598 drive-strength = <2>;
607 drive-strength = <2>;
615 /* SoMC Nile platform's eMMC doesn't support HS200 mode */
618 mmc-hs400-enhanced-strobe;
620 vmmc-supply = <&vreg_l4b_2p95>;
621 vqmmc-supply = <&vreg_l8a_1p8>;
627 vmmc-supply = <&vreg_l5b_2p95>;
628 vqmmc-supply = <&vreg_l2b_2p95>;
632 gpio-reserved-ranges = <8 4>;
634 ts_int_active: ts-int-active-state {
637 drive-strength = <8>;
641 ts_lcd_id_active: ts-lcd-id-active-state {
644 drive-strength = <8>;
648 imx300_vana_default: imx300-vana-default-state {
652 drive-strength = <2>;
655 imx219_vana_default: imx219-vana-default-state {
659 drive-strength = <2>;
662 cam_vdig_default: cam-vdig-default-state {
666 drive-strength = <2>;
671 qcom,select-utmi-as-pipe-clk;
677 maximum-speed = "high-speed";
679 phy-names = "usb2-phy";
681 dr_mode = "peripheral";
682 extcon = <&extcon_usb>;