arch/arm/boot/dts/motorola-mapphone-common.dtsi

   1 // SPDX-License-Identifier: GPL-2.0-only
   2 /dts-v1/;
   3
   4 #include <dt-bindings/input/input.h>
   5 #include "omap443x.dtsi"
   6 #include "motorola-cpcap-mapphone.dtsi"
   7
   8 / {
   9         chosen {
  10                 stdout-path = &uart3;
  11         };
  12
  13         aliases {
  14                 display0 = &lcd0;
  15                 display1 = &hdmi0;
  16         };
  17
  18         /*
  19          * We seem to have only 1021 MB accessible, 1021 - 1022 is locked,
  20          * then 1023 - 1024 seems to contain mbm.
  21          */
  22         memory {
  23                 device_type = "memory";
  24                 reg = <0x80000000 0x3fd00000>;  /* 1021 MB */
  25         };
  26
  27         /* Poweroff GPIO probably connected to CPCAP */
  28         gpio-poweroff {
  29                 compatible = "gpio-poweroff";
  30                 pinctrl-0 = <&poweroff_gpio>;
  31                 pinctrl-names = "default";
  32                 gpios = <&gpio2 18 GPIO_ACTIVE_LOW>;    /* gpio50 */
  33         };
  34
  35         hdmi0: connector {
  36                 compatible = "hdmi-connector";
  37                 pinctrl-0 = <&hdmi_hpd_gpio>;
  38                 pinctrl-names = "default";
  39                 label = "hdmi";
  40                 type = "d";
  41
  42                 hpd-gpios = <&gpio2 31 GPIO_ACTIVE_HIGH>;       /* gpio63 */
  43
  44                 port {
  45                         hdmi_connector_in: endpoint {
  46                                 remote-endpoint = <&hdmi_out>;
  47                         };
  48                 };
  49         };
  50
  51         /*
  52          * HDMI 5V regulator probably sourced from battery. Let's keep
  53          * keep this as always enabled for HDMI to work until we've
  54          * figured what the encoder chip is.
  55          */
  56         hdmi_regulator: regulator-hdmi {
  57                 compatible = "regulator-fixed";
  58                 regulator-name = "hdmi";
  59                 regulator-min-microvolt = <5000000>;
  60                 regulator-max-microvolt = <5000000>;
  61                 gpio = <&gpio2 27 GPIO_ACTIVE_HIGH>;    /* gpio59 */
  62                 enable-active-high;
  63                 regulator-always-on;
  64         };
  65
  66         /* FS USB Host PHY on port 1 for mdm6600 */
  67         fsusb1_phy: usb-phy@1 {
  68                 compatible = "motorola,mapphone-mdm6600";
  69                 pinctrl-0 = <&usb_mdm6600_pins>;
  70                 pinctrl-names = "default";
  71                 enable-gpios = <&gpio3 31 GPIO_ACTIVE_LOW>;     /* gpio_95 */
  72                 power-gpios = <&gpio2 22 GPIO_ACTIVE_HIGH>;     /* gpio_54 */
  73                 reset-gpios = <&gpio2 17 GPIO_ACTIVE_HIGH>;     /* gpio_49 */
  74                 /* mode: gpio_148 gpio_149 */
  75                 motorola,mode-gpios = <&gpio5 20 GPIO_ACTIVE_HIGH>,
  76                                       <&gpio5 21 GPIO_ACTIVE_HIGH>;
  77                 /* cmd: gpio_103 gpio_104 gpio_142 */
  78                 motorola,cmd-gpios = <&gpio4 7 GPIO_ACTIVE_HIGH>,
  79                                      <&gpio4 8 GPIO_ACTIVE_HIGH>,
  80                                      <&gpio5 14 GPIO_ACTIVE_HIGH>;
  81                 /* status: gpio_52 gpio_53 gpio_55 */
  82                 motorola,status-gpios = <&gpio2 20 GPIO_ACTIVE_HIGH>,
  83                                         <&gpio2 21 GPIO_ACTIVE_HIGH>,
  84                                         <&gpio2 23 GPIO_ACTIVE_HIGH>;
  85                 #phy-cells = <0>;
  86         };
  87
  88         /* HS USB host TLL nop-phy on port 2 for w3glte */
  89         hsusb2_phy: usb-phy@2 {
  90                 compatible = "usb-nop-xceiv";
  91                 #phy-cells = <0>;
  92         };
  93
  94         /* LCD regulator from sw5 source */
  95         lcd_regulator: regulator-lcd {
  96                 compatible = "regulator-fixed";
  97                 regulator-name = "lcd";
  98                 regulator-min-microvolt = <5050000>;
  99                 regulator-max-microvolt = <5050000>;
 100                 gpio = <&gpio4 0 GPIO_ACTIVE_HIGH>;     /* gpio96 */
 101                 enable-active-high;
 102                 vin-supply = <&sw5>;
 103         };
 104
 105         /* This is probably coming straight from the battery.. */
 106         wl12xx_vmmc: regulator-wl12xx {
 107                 compatible = "regulator-fixed";
 108                 regulator-name = "vwl1271";
 109                 regulator-min-microvolt = <1650000>;
 110                 regulator-max-microvolt = <1650000>;
 111                 gpio = <&gpio3 30 GPIO_ACTIVE_HIGH>;    /* gpio94 */
 112                 startup-delay-us = <70000>;
 113                 enable-active-high;
 114         };
 115
 116         gpio_keys {
 117                 compatible = "gpio-keys";
 118
 119                 volume_down {
 120                         label = "Volume Down";
 121                         gpios = <&gpio5 26 GPIO_ACTIVE_LOW>; /* gpio154 */
 122                         linux,code = <KEY_VOLUMEDOWN>;
 123                         linux,can-disable;
 124                         /* Value above 7.95ms for no GPIO hardware debounce */
 125                         debounce-interval = <10>;
 126                 };
 127
 128                 slider {
 129                         label = "Keypad Slide";
 130                         gpios = <&gpio4 26 GPIO_ACTIVE_HIGH>; /* gpio122 */
 131                         linux,input-type = <EV_SW>;
 132                         linux,code = <SW_KEYPAD_SLIDE>;
 133                         linux,can-disable;
 134                         /* Value above 7.95ms for no GPIO hardware debounce */
 135                         debounce-interval = <10>;
 136                 };
 137         };
 138
 139         soundcard {
 140                 compatible = "audio-graph-card";
 141                 label = "Droid 4 Audio";
 142
 143                 widgets =
 144                         "Speaker", "Earpiece",
 145                         "Speaker", "Loudspeaker",
 146                         "Headphone", "Headphone Jack",
 147                         "Microphone", "Internal Mic";
 148
 149                 routing =
 150                         "Earpiece", "EP",
 151                         "Loudspeaker", "SPKR",
 152                         "Headphone Jack", "HSL",
 153                         "Headphone Jack", "HSR",
 154                         "MICR", "Internal Mic";
 155
 156                 dais = <&mcbsp2_port>, <&mcbsp3_port>;
 157         };
 158
 159         pwm8: dmtimer-pwm-8 {
 160                 pinctrl-names = "default";
 161                 pinctrl-0 = <&vibrator_direction_pin>;
 162
 163                 compatible = "ti,omap-dmtimer-pwm";
 164                 #pwm-cells = <3>;
 165                 ti,timers = <&timer8>;
 166                 ti,clock-source = <0x01>;
 167         };
 168
 169         pwm9: dmtimer-pwm-9 {
 170                 pinctrl-names = "default";
 171                 pinctrl-0 = <&vibrator_enable_pin>;
 172
 173                 compatible = "ti,omap-dmtimer-pwm";
 174                 #pwm-cells = <3>;
 175                 ti,timers = <&timer9>;
 176                 ti,clock-source = <0x01>;
 177         };
 178
 179         vibrator {
 180                 compatible = "pwm-vibrator";
 181                 pwms = <&pwm9 0 10000000 0>, <&pwm8 0 10000000 0>;
 182                 pwm-names = "enable", "direction";
 183                 direction-duty-cycle-ns = <10000000>;
 184         };
 185
 186         backlight: backlight {
 187                 compatible = "led-backlight";
 188
 189                 leds = <&backlight_led>;
 190                 brightness-levels = <31 63 95 127 159 191 223 255>;
 191                 default-brightness-level = <6>;
 192         };
 193 };
 194
 195 &dss {
 196         status = "okay";
 197 };
 198
 199 &dsi1 {
 200         status = "okay";
 201         vdd-supply = <&vcsi>;
 202
 203         port {
 204                 dsi1_out_ep: endpoint {
 205                         remote-endpoint = <&lcd0_in>;
 206                         lanes = <0 1 2 3 4 5>;
 207                 };
 208         };
 209
 210         lcd0: panel@0 {
 211                 compatible = "motorola,droid4-panel", "panel-dsi-cm";
 212                 reg = <0>;
 213                 label = "lcd0";
 214                 vddi-supply = <&lcd_regulator>;
 215                 reset-gpios = <&gpio4 5 GPIO_ACTIVE_HIGH>;      /* gpio101 */
 216
 217                 backlight = <&backlight>;
 218
 219                 width-mm = <50>;
 220                 height-mm = <89>;
 221                 rotation = <90>;
 222
 223                 panel-timing {
 224                         clock-frequency = <0>;          /* Calculated by dsi */
 225
 226                         hback-porch = <2>;
 227                         hactive = <540>;
 228                         hfront-porch = <0>;
 229                         hsync-len = <2>;
 230
 231                         vback-porch = <1>;
 232                         vactive = <960>;
 233                         vfront-porch = <0>;
 234                         vsync-len = <1>;
 235
 236                         hsync-active = <0>;
 237                         vsync-active = <0>;
 238                         de-active = <1>;
 239                         pixelclk-active = <1>;
 240                 };
 241
 242                 port {
 243                         lcd0_in: endpoint {
 244                                 remote-endpoint = <&dsi1_out_ep>;
 245                         };
 246                 };
 247         };
 248 };
 249
 250 &hdmi {
 251         status = "okay";
 252         pinctrl-0 = <&dss_hdmi_pins>;
 253         pinctrl-names = "default";
 254         vdda-supply = <&vdac>;
 255
 256         port {
 257                 hdmi_out: endpoint {
 258                         remote-endpoint = <&hdmi_connector_in>;
 259                         lanes = <1 0 3 2 5 4 7 6>;
 260                 };
 261         };
 262 };
 263
 264 /* Battery NVRAM on 1-wire handled by w1_ds250x driver */
 265 &hdqw1w {
 266         pinctrl-0 = <&hdq_pins>;
 267         pinctrl-names = "default";
 268         ti,mode = "1w";
 269 };
 270
 271 &i2c1 {
 272         tmp105@48 {
 273                 compatible = "ti,tmp105";
 274                 reg = <0x48>;
 275                 pinctrl-0 = <&tmp105_irq>;
 276                 pinctrl-names = "default";
 277                 /* kpd_row0.gpio_178 */
 278                 interrupts-extended = <&gpio6 18 IRQ_TYPE_EDGE_FALLING
 279                                        &omap4_pmx_core 0x14e>;
 280                 interrupt-names = "irq", "wakeup";
 281                 wakeup-source;
 282         };
 283 };
 284
 285 &keypad {
 286         keypad,num-rows = <8>;
 287         keypad,num-columns = <8>;
 288         linux,keymap = <
 289
 290         /* Row 1 */
 291         MATRIX_KEY(0, 2, KEY_1)
 292         MATRIX_KEY(0, 6, KEY_2)
 293         MATRIX_KEY(2, 3, KEY_3)
 294         MATRIX_KEY(0, 7, KEY_4)
 295         MATRIX_KEY(0, 4, KEY_5)
 296         MATRIX_KEY(5, 5, KEY_6)
 297         MATRIX_KEY(0, 1, KEY_7)
 298         MATRIX_KEY(0, 5, KEY_8)
 299         MATRIX_KEY(0, 0, KEY_9)
 300         MATRIX_KEY(1, 6, KEY_0)
 301
 302         /* Row 2 */
 303         MATRIX_KEY(3, 4, KEY_APOSTROPHE)
 304         MATRIX_KEY(7, 6, KEY_Q)
 305         MATRIX_KEY(7, 7, KEY_W)
 306         MATRIX_KEY(7, 2, KEY_E)
 307         MATRIX_KEY(1, 0, KEY_R)
 308         MATRIX_KEY(4, 4, KEY_T)
 309         MATRIX_KEY(1, 2, KEY_Y)
 310         MATRIX_KEY(6, 7, KEY_U)
 311         MATRIX_KEY(2, 2, KEY_I)
 312         MATRIX_KEY(5, 6, KEY_O)
 313         MATRIX_KEY(3, 7, KEY_P)
 314         MATRIX_KEY(6, 5, KEY_BACKSPACE)
 315
 316         /* Row 3 */
 317         MATRIX_KEY(5, 4, KEY_TAB)
 318         MATRIX_KEY(5, 7, KEY_A)
 319         MATRIX_KEY(2, 7, KEY_S)
 320         MATRIX_KEY(7, 0, KEY_D)
 321         MATRIX_KEY(2, 6, KEY_F)
 322         MATRIX_KEY(6, 2, KEY_G)
 323         MATRIX_KEY(6, 6, KEY_H)
 324         MATRIX_KEY(1, 4, KEY_J)
 325         MATRIX_KEY(3, 1, KEY_K)
 326         MATRIX_KEY(2, 1, KEY_L)
 327         MATRIX_KEY(4, 6, KEY_ENTER)
 328
 329         /* Row 4 */
 330         MATRIX_KEY(3, 6, KEY_LEFTSHIFT)         /* KEY_CAPSLOCK */
 331         MATRIX_KEY(6, 1, KEY_Z)
 332         MATRIX_KEY(7, 4, KEY_X)
 333         MATRIX_KEY(5, 1, KEY_C)
 334         MATRIX_KEY(1, 7, KEY_V)
 335         MATRIX_KEY(2, 4, KEY_B)
 336         MATRIX_KEY(4, 1, KEY_N)
 337         MATRIX_KEY(1, 1, KEY_M)
 338         MATRIX_KEY(3, 5, KEY_COMMA)
 339         MATRIX_KEY(5, 2, KEY_DOT)
 340         MATRIX_KEY(6, 3, KEY_UP)
 341         MATRIX_KEY(7, 3, KEY_OK)
 342
 343         /* Row 5 */
 344         MATRIX_KEY(2, 5, KEY_LEFTCTRL)          /* KEY_LEFTSHIFT */
 345         MATRIX_KEY(4, 5, KEY_LEFTALT)           /* SYM */
 346         MATRIX_KEY(6, 0, KEY_MINUS)
 347         MATRIX_KEY(4, 7, KEY_EQUAL)
 348         MATRIX_KEY(1, 5, KEY_SPACE)
 349         MATRIX_KEY(3, 2, KEY_SLASH)
 350         MATRIX_KEY(4, 3, KEY_LEFT)
 351         MATRIX_KEY(5, 3, KEY_DOWN)
 352         MATRIX_KEY(3, 3, KEY_RIGHT)
 353
 354         /* Side buttons, KEY_VOLUMEDOWN and KEY_PWER are on CPCAP? */
 355         MATRIX_KEY(5, 0, KEY_VOLUMEUP)
 356         >;
 357 };
 358
 359 &mmc1 {
 360         vmmc-supply = <&vwlan2>;
 361         bus-width = <4>;
 362         cd-gpios = <&gpio6 16 GPIO_ACTIVE_LOW>; /* gpio176 */
 363 };
 364
 365 &mmc2 {
 366         vmmc-supply = <&vsdio>;
 367         bus-width = <8>;
 368         ti,non-removable;
 369 };
 370
 371 &mmc3 {
 372         pinctrl-names = "default";
 373         pinctrl-0 = <&mmc3_pins>;
 374         vmmc-supply = <&wl12xx_vmmc>;
 375         /* uart2_tx.sdmmc3_dat1 pad as wakeirq */
 376         interrupts-extended = <&wakeupgen GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH
 377                                &omap4_pmx_core 0xde>;
 378         interrupt-names = "irq", "wakeup";
 379         non-removable;
 380         bus-width = <4>;
 381         cap-power-off-card;
 382         keep-power-in-suspend;
 383
 384         #address-cells = <1>;
 385         #size-cells = <0>;
 386         wlcore: wlcore@2 {
 387                 compatible = "ti,wl1285", "ti,wl1283";
 388                 reg = <2>;
 389                 /* gpio_100 with gpmc_wait2 pad as wakeirq */
 390                 interrupts-extended = <&gpio4 4 IRQ_TYPE_LEVEL_HIGH>,
 391                                       <&omap4_pmx_core 0x4e>;
 392                 interrupt-names = "irq", "wakeup";
 393                 ref-clock-frequency = <26000000>;
 394                 tcxo-clock-frequency = <26000000>;
 395         };
 396 };
 397
 398 &i2c1 {
 399         led-controller@38 {
 400                 compatible = "ti,lm3532";
 401                 #address-cells = <1>;
 402                 #size-cells = <0>;
 403                 reg = <0x38>;
 404
 405                 enable-gpios = <&gpio6 12 GPIO_ACTIVE_HIGH>;
 406
 407                 ramp-up-us = <1024>;
 408                 ramp-down-us = <8193>;
 409
 410                 backlight_led: led@0 {
 411                         reg = <0>;
 412                         led-sources = <2>;
 413                         ti,led-mode = <0>;
 414                         label = ":backlight";
 415                 };
 416
 417                 led@1 {
 418                         reg = <1>;
 419                         led-sources = <1>;
 420                         ti,led-mode = <0>;
 421                         label = ":kbd_backlight";
 422                 };
 423         };
 424 };
 425
 426 &i2c2 {
 427         touchscreen@4a {
 428                 compatible = "atmel,maxtouch";
 429                 reg = <0x4a>;
 430                 pinctrl-names = "default";
 431                 pinctrl-0 = <&touchscreen_pins>;
 432
 433                 reset-gpios = <&gpio6 13 GPIO_ACTIVE_LOW>; /* gpio173 */
 434
 435                 /* gpio_183 with sys_nirq2 pad as wakeup */
 436                 interrupts-extended = <&gpio6 23 IRQ_TYPE_LEVEL_LOW>,
 437                                       <&omap4_pmx_core 0x160>;
 438                 interrupt-names = "irq", "wakeup";
 439                 wakeup-source;
 440         };
 441
 442         isl29030@44 {
 443                 compatible = "isil,isl29030";
 444                 reg = <0x44>;
 445
 446                 pinctrl-names = "default";
 447                 pinctrl-0 = <&als_proximity_pins>;
 448
 449                 interrupt-parent = <&gpio6>;
 450                 interrupts = <17 IRQ_TYPE_LEVEL_LOW>; /* gpio177 */
 451         };
 452 };
 453
 454 &omap4_pmx_core {
 455
 456         /* hdmi_hpd.gpio_63 */
 457         hdmi_hpd_gpio: pinmux_hdmi_hpd_pins {
 458                 pinctrl-single,pins = <
 459                 OMAP4_IOPAD(0x098, PIN_INPUT | MUX_MODE3)
 460                 >;
 461         };
 462
 463         hdq_pins: pinmux_hdq_pins {
 464                 pinctrl-single,pins = <
 465                 /* 0x4a100120 hdq_sio.hdq_sio aa27 */
 466                 OMAP4_IOPAD(0x120, PIN_INPUT | MUX_MODE0)
 467                 >;
 468         };
 469
 470         /* hdmi_cec.hdmi_cec, hdmi_scl.hdmi_scl, hdmi_sda.hdmi_sda */
 471         dss_hdmi_pins: pinmux_dss_hdmi_pins {
 472                 pinctrl-single,pins = <
 473                 OMAP4_IOPAD(0x09a, PIN_INPUT | MUX_MODE0)
 474                 OMAP4_IOPAD(0x09c, PIN_INPUT | MUX_MODE0)
 475                 OMAP4_IOPAD(0x09e, PIN_INPUT | MUX_MODE0)
 476                 >;
 477         };
 478
 479         /*
 480          * Android uses PIN_OFF_INPUT_PULLDOWN | PIN_INPUT_PULLUP | MUX_MODE3
 481          * for gpio_100, but the internal pull makes wlan flakey on some
 482          * devices. Off mode value should be tested if we have off mode working
 483          * later on.
 484          */
 485         mmc3_pins: pinmux_mmc3_pins {
 486                 pinctrl-single,pins = <
 487                 /* 0x4a10008e gpmc_wait2.gpio_100 d23 */
 488                 OMAP4_IOPAD(0x08e, PIN_INPUT | MUX_MODE3)
 489
 490                 /* 0x4a100102 abe_mcbsp1_dx.sdmmc3_dat2 ab25 */
 491                 OMAP4_IOPAD(0x102, PIN_INPUT_PULLUP | MUX_MODE1)
 492
 493                 /* 0x4a100104 abe_mcbsp1_fsx.sdmmc3_dat3 ac27 */
 494                 OMAP4_IOPAD(0x104, PIN_INPUT_PULLUP | MUX_MODE1)
 495
 496                 /* 0x4a100118 uart2_cts.sdmmc3_clk ab26 */
 497                 OMAP4_IOPAD(0x118, PIN_INPUT | MUX_MODE1)
 498
 499                 /* 0x4a10011a uart2_rts.sdmmc3_cmd ab27 */
 500                 OMAP4_IOPAD(0x11a, PIN_INPUT_PULLUP | MUX_MODE1)
 501
 502                 /* 0x4a10011c uart2_rx.sdmmc3_dat0 aa25 */
 503                 OMAP4_IOPAD(0x11c, PIN_INPUT_PULLUP | MUX_MODE1)
 504
 505                 /* 0x4a10011e uart2_tx.sdmmc3_dat1 aa26 */
 506                 OMAP4_IOPAD(0x11e, PIN_INPUT_PULLUP | MUX_MODE1)
 507                 >;
 508         };
 509
 510         /* gpmc_ncs0.gpio_50 */
 511         poweroff_gpio: pinmux_poweroff_pins {
 512                 pinctrl-single,pins = <
 513                 OMAP4_IOPAD(0x074, PIN_OUTPUT_PULLUP | MUX_MODE3)
 514                 >;
 515         };
 516
 517         /* kpd_row0.gpio_178 */
 518         tmp105_irq: pinmux_tmp105_irq {
 519                 pinctrl-single,pins = <
 520                 OMAP4_IOPAD(0x18e, PIN_INPUT_PULLUP | MUX_MODE3)
 521                 >;
 522         };
 523
 524         usb_gpio_mux_sel1: pinmux_usb_gpio_mux_sel1_pins {
 525                 /* gpio_60 */
 526                 pinctrl-single,pins = <
 527                 OMAP4_IOPAD(0x088, PIN_OUTPUT | MUX_MODE3)
 528                 >;
 529         };
 530
 531         touchscreen_pins: pinmux_touchscreen_pins {
 532                 pinctrl-single,pins = <
 533                 OMAP4_IOPAD(0x180, PIN_OUTPUT | MUX_MODE3)
 534                 OMAP4_IOPAD(0x1a0, PIN_INPUT_PULLUP | MUX_MODE3)
 535                 >;
 536         };
 537
 538         als_proximity_pins: pinmux_als_proximity_pins {
 539                 pinctrl-single,pins = <
 540                 OMAP4_IOPAD(0x18c, PIN_INPUT_PULLUP | MUX_MODE3)
 541                 >;
 542         };
 543
 544         usb_mdm6600_pins: pinmux_usb_mdm6600_pins {
 545                 pinctrl-single,pins = <
 546                 /* enable 0x4a1000d8 usbb1_ulpitll_dat7.gpio_95 ag16 */
 547                 OMAP4_IOPAD(0x0d8, PIN_INPUT | MUX_MODE3)
 548
 549                 /* power 0x4a10007c gpmc_nwp.gpio_54 c25 */
 550                 OMAP4_IOPAD(0x07c, PIN_OUTPUT | MUX_MODE3)
 551
 552                 /* reset 0x4a100072 gpmc_a25.gpio_49 d20 */
 553                 OMAP4_IOPAD(0x072, PIN_OUTPUT | MUX_MODE3)
 554
 555                 /* mode0/bpwake 0x4a10014e sdmmc5_dat1.gpio_148 af4 */
 556                 OMAP4_IOPAD(0x14e, PIN_OUTPUT | MUX_MODE3)
 557
 558                 /* mode1/apwake 0x4a100150 sdmmc5_dat2.gpio_149 ag3 */
 559                 OMAP4_IOPAD(0x150, PIN_OFF_OUTPUT_LOW | PIN_INPUT | MUX_MODE3)
 560
 561                 /* status0 0x4a10007e gpmc_clk.gpio_55 b22 */
 562                 OMAP4_IOPAD(0x07e, PIN_INPUT | MUX_MODE3)
 563
 564                 /* status1 0x4a10007a gpmc_ncs3.gpio_53 c22 */
 565                 OMAP4_IOPAD(0x07a, PIN_INPUT | MUX_MODE3)
 566
 567                 /* status2 0x4a100078 gpmc_ncs2.gpio_52 d21 */
 568                 OMAP4_IOPAD(0x078, PIN_INPUT | MUX_MODE3)
 569
 570                 /* cmd0 0x4a100094 gpmc_ncs6.gpio_103 c24 */
 571                 OMAP4_IOPAD(0x094, PIN_OUTPUT | MUX_MODE3)
 572
 573                 /* cmd1 0x4a100096 gpmc_ncs7.gpio_104 d24 */
 574                 OMAP4_IOPAD(0x096, PIN_OUTPUT | MUX_MODE3)
 575
 576                 /* cmd2 0x4a100142 uart3_rts_sd.gpio_142 f28 */
 577                 OMAP4_IOPAD(0x142, PIN_OUTPUT | MUX_MODE3)
 578                 >;
 579         };
 580
 581         usb_ulpi_pins: pinmux_usb_ulpi_pins {
 582                 pinctrl-single,pins = <
 583                 OMAP4_IOPAD(0x196, MUX_MODE7)
 584                 OMAP4_IOPAD(0x198, MUX_MODE7)
 585                 OMAP4_IOPAD(0x1b2, PIN_INPUT_PULLUP | MUX_MODE0)
 586                 OMAP4_IOPAD(0x1b4, PIN_INPUT_PULLUP | MUX_MODE0)
 587                 OMAP4_IOPAD(0x1b6, PIN_INPUT_PULLUP | MUX_MODE0)
 588                 OMAP4_IOPAD(0x1b8, PIN_INPUT_PULLUP | MUX_MODE0)
 589                 OMAP4_IOPAD(0x1ba, PIN_INPUT_PULLUP | MUX_MODE0)
 590                 OMAP4_IOPAD(0x1bc, PIN_INPUT_PULLUP | MUX_MODE0)
 591                 OMAP4_IOPAD(0x1be, PIN_INPUT_PULLUP | MUX_MODE0)
 592                 OMAP4_IOPAD(0x1c0, PIN_INPUT_PULLUP | MUX_MODE0)
 593                 OMAP4_IOPAD(0x1c2, PIN_INPUT_PULLUP | MUX_MODE0)
 594                 OMAP4_IOPAD(0x1c4, PIN_INPUT_PULLUP | MUX_MODE0)
 595                 OMAP4_IOPAD(0x1c6, PIN_INPUT_PULLUP | MUX_MODE0)
 596                 OMAP4_IOPAD(0x1c8, PIN_INPUT_PULLUP | MUX_MODE0)
 597                 >;
 598         };
 599
 600         /* usb0_otg_dp and usb0_otg_dm */
 601         usb_utmi_pins: pinmux_usb_utmi_pins {
 602                 pinctrl-single,pins = <
 603                 OMAP4_IOPAD(0x196, PIN_INPUT | MUX_MODE0)
 604                 OMAP4_IOPAD(0x198, PIN_INPUT | MUX_MODE0)
 605                 OMAP4_IOPAD(0x1b2, PIN_INPUT_PULLUP | MUX_MODE7)
 606                 OMAP4_IOPAD(0x1b4, PIN_INPUT_PULLUP | MUX_MODE7)
 607                 OMAP4_IOPAD(0x1b6, PIN_INPUT_PULLUP | MUX_MODE7)
 608                 OMAP4_IOPAD(0x1b8, PIN_INPUT_PULLUP | MUX_MODE7)
 609                 OMAP4_IOPAD(0x1ba, PIN_INPUT_PULLUP | MUX_MODE7)
 610                 OMAP4_IOPAD(0x1bc, PIN_INPUT_PULLUP | MUX_MODE7)
 611                 OMAP4_IOPAD(0x1be, PIN_INPUT_PULLUP | MUX_MODE7)
 612                 OMAP4_IOPAD(0x1c0, PIN_INPUT_PULLUP | MUX_MODE7)
 613                 OMAP4_IOPAD(0x1c2, PIN_INPUT_PULLUP | MUX_MODE7)
 614                 OMAP4_IOPAD(0x1c4, PIN_INPUT_PULLUP | MUX_MODE7)
 615                 OMAP4_IOPAD(0x1c6, PIN_INPUT_PULLUP | MUX_MODE7)
 616                 OMAP4_IOPAD(0x1c8, PIN_INPUT_PULLUP | MUX_MODE7)
 617                 >;
 618         };
 619
 620         /*
 621          * Note that the v3.0.8 stock userspace dynamically remuxes uart1
 622          * rts pin probably for PM purposes to PIN_INPUT_PULLUP | MUX_MODE7
 623          * when not used. If needed, we can add rts pin remux later based
 624          * on power measurements.
 625          */
 626         uart1_pins: pinmux_uart1_pins {
 627                 pinctrl-single,pins = <
 628                 /* 0x4a10013c mcspi1_cs2.uart1_cts ag23 */
 629                 OMAP4_IOPAD(0x13c, PIN_INPUT_PULLUP | MUX_MODE1)
 630
 631                 /* 0x4a10013e mcspi1_cs3.uart1_rts ah23 */
 632                 OMAP4_IOPAD(0x13e, MUX_MODE1)
 633
 634                 /* 0x4a100140 uart3_cts_rctx.uart1_tx f27 */
 635                 OMAP4_IOPAD(0x140, PIN_OUTPUT | MUX_MODE1)
 636
 637                 /* 0x4a1001ca dpm_emu14.uart1_rx aa3 */
 638                 OMAP4_IOPAD(0x1ca, PIN_INPUT_PULLUP | MUX_MODE2)
 639                 >;
 640         };
 641
 642         /* uart3_tx_irtx and uart3_rx_irrx */
 643         uart3_pins: pinmux_uart3_pins {
 644                 pinctrl-single,pins = <
 645                 OMAP4_IOPAD(0x196, MUX_MODE7)
 646                 OMAP4_IOPAD(0x198, MUX_MODE7)
 647                 OMAP4_IOPAD(0x1b2, PIN_INPUT_PULLUP | MUX_MODE7)
 648                 OMAP4_IOPAD(0x1b4, PIN_INPUT_PULLUP | MUX_MODE7)
 649                 OMAP4_IOPAD(0x1b6, PIN_INPUT_PULLUP | MUX_MODE7)
 650                 OMAP4_IOPAD(0x1b8, PIN_INPUT_PULLUP | MUX_MODE7)
 651                 OMAP4_IOPAD(0x1ba, MUX_MODE2)
 652                 OMAP4_IOPAD(0x1bc, PIN_INPUT | MUX_MODE2)
 653                 OMAP4_IOPAD(0x1be, PIN_INPUT_PULLUP | MUX_MODE7)
 654                 OMAP4_IOPAD(0x1c0, PIN_INPUT_PULLUP | MUX_MODE7)
 655                 OMAP4_IOPAD(0x1c2, PIN_INPUT_PULLUP | MUX_MODE7)
 656                 OMAP4_IOPAD(0x1c4, PIN_INPUT_PULLUP | MUX_MODE7)
 657                 OMAP4_IOPAD(0x1c6, PIN_INPUT_PULLUP | MUX_MODE7)
 658                 OMAP4_IOPAD(0x1c8, PIN_INPUT_PULLUP | MUX_MODE7)
 659                 >;
 660         };
 661
 662         uart4_pins: pinmux_uart4_pins {
 663                 pinctrl-single,pins = <
 664                 OMAP4_IOPAD(0x15c, PIN_INPUT | MUX_MODE0)               /* uart4_rx */
 665                 OMAP4_IOPAD(0x15e, PIN_OUTPUT | MUX_MODE0)              /* uart4_tx */
 666                 OMAP4_IOPAD(0x110, PIN_INPUT_PULLUP | MUX_MODE5)        /* uart4_cts */
 667                 OMAP4_IOPAD(0x112, PIN_OUTPUT_PULLUP | MUX_MODE5)       /* uart4_rts */
 668                 >;
 669         };
 670
 671         mcbsp2_pins: pinmux_mcbsp2_pins {
 672                 pinctrl-single,pins = <
 673                 OMAP4_IOPAD(0x0f6, PIN_INPUT | MUX_MODE0)       /* abe_mcbsp2_clkx */
 674                 OMAP4_IOPAD(0x0f8, PIN_INPUT | MUX_MODE0)       /* abe_mcbsp2_dr */
 675                 OMAP4_IOPAD(0x0fa, PIN_OUTPUT | MUX_MODE0)      /* abe_mcbsp2_dx */
 676                 OMAP4_IOPAD(0x0fc, PIN_INPUT | MUX_MODE0)       /* abe_mcbsp2_fsx */
 677                 >;
 678         };
 679
 680         mcbsp3_pins: pinmux_mcbsp3_pins {
 681                 pinctrl-single,pins = <
 682                 OMAP4_IOPAD(0x106, PIN_INPUT | MUX_MODE1)       /* abe_mcbsp3_dr */
 683                 OMAP4_IOPAD(0x108, PIN_OUTPUT | MUX_MODE1)      /* abe_mcbsp3_dx */
 684                 OMAP4_IOPAD(0x10a, PIN_INPUT | MUX_MODE1)       /* abe_mcbsp3_clkx */
 685                 OMAP4_IOPAD(0x10c, PIN_INPUT | MUX_MODE1)       /* abe_mcbsp3_fsx */
 686                 >;
 687         };
 688
 689         vibrator_direction_pin: pinmux_vibrator_direction_pin {
 690                 pinctrl-single,pins = <
 691                 OMAP4_IOPAD(0x1ce, PIN_OUTPUT | MUX_MODE1)      /* dmtimer8_pwm_evt (gpio_27) */
 692                 >;
 693         };
 694
 695         vibrator_enable_pin: pinmux_vibrator_enable_pin {
 696                 pinctrl-single,pins = <
 697                 OMAP4_IOPAD(0X1d0, PIN_OUTPUT | MUX_MODE1)      /* dmtimer9_pwm_evt (gpio_28) */
 698                 >;
 699         };
 700 };
 701
 702 &omap4_pmx_wkup {
 703         usb_gpio_mux_sel2: pinmux_usb_gpio_mux_sel2_pins {
 704                 /* gpio_wk0 */
 705                 pinctrl-single,pins = <
 706                 OMAP4_IOPAD(0x040, PIN_OUTPUT_PULLDOWN | MUX_MODE3)
 707                 >;
 708         };
 709 };
 710
 711 /* RNG is used by secure mode and not accessible */
 712 &rng_target {
 713         status = "disabled";
 714 };
 715
 716 /* Configure pwm clock source for timers 8 & 9 */
 717 &timer8 {
 718         assigned-clocks = <&abe_clkctrl OMAP4_TIMER8_CLKCTRL 24>;
 719         assigned-clock-parents = <&sys_clkin_ck>;
 720 };
 721
 722 &timer9 {
 723         assigned-clocks = <&l4_per_clkctrl OMAP4_TIMER9_CLKCTRL 24>;
 724         assigned-clock-parents = <&sys_clkin_ck>;
 725 };
 726
 727 /*
 728  * The uart1 port is wired to mdm6600 with rts and cts. The modem uses gpio_149
 729  * for wake-up events for both the USB PHY and the UART. We can use gpio_149
 730  * pad as the shared wakeirq for the UART rather than the RX or CTS pad as we
 731  * have gpio_149 trigger before the UART transfer starts.
 732  */
 733 &uart1 {
 734         pinctrl-names = "default";
 735         pinctrl-0 = <&uart1_pins>;
 736         interrupts-extended = <&wakeupgen GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH
 737                                &omap4_pmx_core 0x110>;
 738         uart-has-rtscts;
 739         current-speed = <115200>;
 740 };
 741
 742 &uart3 {
 743         interrupts-extended = <&wakeupgen GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH
 744                                &omap4_pmx_core 0x17c>;
 745 };
 746
 747 &uart4 {
 748         pinctrl-names = "default";
 749         pinctrl-0 = <&uart4_pins>;
 750
 751         bluetooth {
 752                 compatible = "ti,wl1285-st";
 753                 enable-gpios = <&gpio6 14 GPIO_ACTIVE_HIGH>; /* gpio 174 */
 754                 max-speed = <3686400>;
 755         };
 756 };
 757
 758 &usbhsohci {
 759         phys = <&fsusb1_phy>;
 760         phy-names = "usb";
 761 };
 762
 763 &usbhsehci {
 764         phys = <&hsusb2_phy>;
 765 };
 766
 767 &usbhshost {
 768         port1-mode = "ohci-phy-4pin-dpdm";
 769         port2-mode = "ehci-tll";
 770 };
 771
 772 /* Internal UTMI+ PHY used for OTG, CPCAP ULPI PHY for detection and charger */
 773 &usb_otg_hs {
 774         interface-type = <1>;
 775         mode = <3>;
 776
 777         /*
 778          * Max 300 mA steps based on similar PMIC MC13783UG.pdf "Table 10-4.
 779          * VBUS Regulator Main Characteristics". Binding uses 2 mA units.
 780          */
 781         power = <150>;
 782 };
 783
 784 &i2c4 {
 785         ak8975: magnetometer@c {
 786                 compatible = "asahi-kasei,ak8975";
 787                 reg = <0x0c>;
 788
 789                 vdd-supply = <&vhvio>;
 790
 791                 interrupt-parent = <&gpio6>;
 792                 interrupts = <15 IRQ_TYPE_EDGE_RISING>; /* gpio175 */
 793
 794                 rotation-matrix = "-1", "0", "0",
 795                                   "0", "1", "0",
 796                                   "0", "0", "-1";
 797
 798         };
 799
 800         lis3dh: accelerometer@18 {
 801                 compatible = "st,lis3dh-accel";
 802                 reg = <0x18>;
 803
 804                 vdd-supply = <&vhvio>;
 805
 806                 interrupt-parent = <&gpio2>;
 807                 interrupts = <2 IRQ_TYPE_EDGE_BOTH>; /* gpio34 */
 808
 809                 rotation-matrix = "0", "-1", "0",
 810                                   "1", "0", "0",
 811                                   "0", "0", "1";
 812         };
 813 };
 814
 815 &mcbsp2 {
 816         #sound-dai-cells = <0>;
 817         pinctrl-names = "default";
 818         pinctrl-0 = <&mcbsp2_pins>;
 819         status = "okay";
 820
 821         mcbsp2_port: port {
 822                 cpu_dai2: endpoint {
 823                         dai-format = "i2s";
 824                         remote-endpoint = <&cpcap_audio_codec0>;
 825                         frame-master = <&cpcap_audio_codec0>;
 826                         bitclock-master = <&cpcap_audio_codec0>;
 827                 };
 828         };
 829 };
 830
 831 &mcbsp3 {
 832         #sound-dai-cells = <0>;
 833         pinctrl-names = "default";
 834         pinctrl-0 = <&mcbsp3_pins>;
 835         status = "okay";
 836
 837         mcbsp3_port: port {
 838                 cpu_dai3: endpoint {
 839                         dai-format = "dsp_a";
 840                         frame-master = <&cpcap_audio_codec1>;
 841                         bitclock-master = <&cpcap_audio_codec1>;
 842                         remote-endpoint = <&cpcap_audio_codec1>;
 843                 };
 844         };
 845 };
 846
 847 &cpcap_audio_codec0 {
 848         remote-endpoint = <&cpu_dai2>;
 849 };
 850
 851 &cpcap_audio_codec1 {
 852         remote-endpoint = <&cpu_dai3>;
 853 };